[PATCH V3 1/2] ARM: imx: add vddsoc/pu setpoint info into dts

[Shawn Guo]

On Wed, Dec 18, 2013 at 04:26:49PM -0500, Anson Huang wrote:
> i.MX6Q needs to update vddarm, vddsoc/pu regulators when cpu freq
> is changed, each setpoint has different voltage, so we need to
> pass vddarm, vddsoc/pu's freq-voltage info from dts together.
> 
> Signed-off-by: Anson Huang <b20788 at freescale.com>
> ---
>  .../devicetree/bindings/cpufreq/cpufreq-imx6.txt   |   56 ++++++++++++++++++++

As I said in V2 review, the device tree binding doc change should be
part of driver patch (patch #2 in this case) or a separate patch, but
never be in the same patch as DTS change.

Shawn

>  arch/arm/boot/dts/imx6q.dtsi                       |    7 +++
>  2 files changed, 63 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/cpufreq/cpufreq-imx6.txt
> 
> diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-imx6.txt b/Documentation/devicetree/bindings/cpufreq/cpufreq-imx6.txt
> new file mode 100644
> index 0000000..cf1c5f7
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/cpufreq/cpufreq-imx6.txt
> @@ -0,0 +1,56 @@
> +i.MX6 cpufreq driver
> +-------------------
> +
> +i.MX6 SoC cpufreq driver for CPU frequency scaling.
> +
> +This binding doc defines properties that must be put in the /cpus/cpu at 0 node,
> +please refer to Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt
> +for detail.
> +
> +Required properties:
> +- operating-points: Refer to Documentation/devicetree/bindings/power/opp.txt
> +  for details.
> +- clocks: Specify clocks that need to be used when cpu frequency is scaled,
> +  refer to Documentation/devicetree/bindings/clock/clock-bindings.txt for
> +  details.
> +- clock-names: List of clock input name strings sorted in the same order as the
> +  clocks property, refer to Documentation/devicetree/bindings/clock/clock-bindings.txt
> +  for details.
> +- xxx-supply: Input voltage supply regulator, refer to
> +  Documentation/devicetree/bindings/regulator/regulator.txt for details.
> +  arm-supply: vddarm input.
> +  pu-supply: vddpu input.
> +  soc-supply: vddsoc input.
> +
> +Optional properties:
> +- fsl,soc-operating-points: Specify vddsoc/pu voltage settings that must
> +  go with cpu0's operating-points.
> +- clock-latency: Specify the possible maximum transition latency for clock,
> +  in unit of nanoseconds.
> +
> +Examples:
> +
> +	cpu at 0 {
> +		operating-points = <
> +			/* kHz    uV */
> +			1200000 1275000
> +			996000  1250000
> +			792000  1150000
> +			396000  975000
> +		>;
> +		fsl,soc-operating-points = <
> +			/* ARM kHz  SOC-PU uV */
> +			1200000 1275000
> +			996000	1250000
> +			792000	1175000
> +			396000	1175000
> +		>;
> +		clock-latency = <61036>; /* two CLK32 periods */
> +		clocks = <&clks 104>, <&clks 6>, <&clks 16>,
> +			 <&clks 17>, <&clks 170>;
> +		clock-names = "arm", "pll2_pfd2_396m", "step",
> +			      "pll1_sw", "pll1_sys";
> +		arm-supply = <&reg_arm>;
> +		pu-supply = <&reg_pu>;
> +		soc-supply = <&reg_soc>;
> +	};
> diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi
> index e7e8332..021e0cb 100644
> --- a/arch/arm/boot/dts/imx6q.dtsi
> +++ b/arch/arm/boot/dts/imx6q.dtsi
> @@ -30,6 +30,13 @@
>  				792000  1150000
>  				396000  975000
>  			>;
> +			fsl,soc-operating-points = <
> +				/* ARM kHz  SOC-PU uV */
> +				1200000 1275000
> +				996000	1250000
> +				792000	1175000
> +				396000	1175000
> +			>;
>  			clock-latency = <61036>; /* two CLK32 periods */
>  			clocks = <&clks 104>, <&clks 6>, <&clks 16>,
>  				 <&clks 17>, <&clks 170>;
> -- 
> 1.7.9.5
> 
>