[PATCH 36/69] ARM: shmobile: Use interrupt macros in board DT files
Simon Horman
horms+renesas at verge.net.au
Thu Dec 12 21:31:10 EST 2013
From: Laurent Pinchart <laurent.pinchart+renesas at ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas at ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas at verge.net.au>
---
arch/arm/boot/dts/r8a73a4-ape6evm.dts | 3 ++-
arch/arm/boot/dts/r8a7740-armadillo800eva-reference.dts | 3 ++-
arch/arm/boot/dts/r8a7778-bockw-reference.dts | 3 ++-
arch/arm/boot/dts/r8a7779-marzen-reference.dts | 3 ++-
arch/arm/boot/dts/sh73a0-kzm9g-reference.dts | 3 ++-
5 files changed, 10 insertions(+), 5 deletions(-)
diff --git a/arch/arm/boot/dts/r8a73a4-ape6evm.dts b/arch/arm/boot/dts/r8a73a4-ape6evm.dts
index 7db8d79..e84d1a7 100644
--- a/arch/arm/boot/dts/r8a73a4-ape6evm.dts
+++ b/arch/arm/boot/dts/r8a73a4-ape6evm.dts
@@ -10,6 +10,7 @@
/dts-v1/;
#include "r8a73a4.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "APE6EVM";
@@ -40,7 +41,7 @@
compatible = "smsc,lan9118", "smsc,lan9115";
reg = <0x08000000 0x1000>;
interrupt-parent = <&irqc1>;
- interrupts = <8 0x4>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
phy-mode = "mii";
reg-io-width = <4>;
smsc,irq-active-high;
diff --git a/arch/arm/boot/dts/r8a7740-armadillo800eva-reference.dts b/arch/arm/boot/dts/r8a7740-armadillo800eva-reference.dts
index c7c5bcb..aef425f 100644
--- a/arch/arm/boot/dts/r8a7740-armadillo800eva-reference.dts
+++ b/arch/arm/boot/dts/r8a7740-armadillo800eva-reference.dts
@@ -11,6 +11,7 @@
/dts-v1/;
#include "r8a7740.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pwm/pwm.h>
/ {
@@ -94,7 +95,7 @@
compatible = "sitronix,st1232";
reg = <0x55>;
interrupt-parent = <&irqpin1>;
- interrupts = <2 0>; /* IRQ10: hwirq 2 on irqpin1 */
+ interrupts = <2 IRQ_TYPE_NONE>; /* IRQ10: hwirq 2 on irqpin1 */
pinctrl-0 = <&st1232_pins>;
pinctrl-names = "default";
gpios = <&pfc 166 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/r8a7778-bockw-reference.dts b/arch/arm/boot/dts/r8a7778-bockw-reference.dts
index be9b753..2000cf8 100644
--- a/arch/arm/boot/dts/r8a7778-bockw-reference.dts
+++ b/arch/arm/boot/dts/r8a7778-bockw-reference.dts
@@ -16,6 +16,7 @@
/dts-v1/;
#include "r8a7778.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "bockw";
@@ -45,7 +46,7 @@
phy-mode = "mii";
interrupt-parent = <&irqpin>;
- interrupts = <0 0>; /* IRQ0: hwirq 0 on irqpin */
+ interrupts = <0 IRQ_TYPE_NONE>; /* IRQ0: hwirq 0 on irqpin */
reg-io-width = <4>;
vddvario-supply = <&fixedregulator3v3>;
vdd33a-supply = <&fixedregulator3v3>;
diff --git a/arch/arm/boot/dts/r8a7779-marzen-reference.dts b/arch/arm/boot/dts/r8a7779-marzen-reference.dts
index 08b9ee37..0f5c614 100644
--- a/arch/arm/boot/dts/r8a7779-marzen-reference.dts
+++ b/arch/arm/boot/dts/r8a7779-marzen-reference.dts
@@ -12,6 +12,7 @@
/dts-v1/;
#include "r8a7779.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "marzen";
@@ -43,7 +44,7 @@
phy-mode = "mii";
interrupt-parent = <&irqpin0>;
- interrupts = <1 0>; /* IRQ1: hwirq 1 on irqpin0 */
+ interrupts = <1 IRQ_TYPE_NONE>; /* IRQ1: hwirq 1 on irqpin0 */
reg-io-width = <4>;
vddvario-supply = <&fixedregulator3v3>;
vdd33a-supply = <&fixedregulator3v3>;
diff --git a/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts b/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts
index d5a6d74..605f6c6 100644
--- a/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts
+++ b/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts
@@ -14,6 +14,7 @@
/dts-v1/;
#include "sh73a0.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "KZM-A9-GT";
@@ -82,7 +83,7 @@
reg = <0x10000000 0x100>;
phy-mode = "mii";
interrupt-parent = <&irqpin0>;
- interrupts = <3 0>; /* active low */
+ interrupts = <3 IRQ_TYPE_NONE>; /* active low */
reg-io-width = <4>;
smsc,irq-push-pull;
smsc,save-mac-address;
--
1.8.4
More information about the linux-arm-kernel
mailing list