[PATCH 4/4] ARM: dts: imx6qdl: add support for Ka-Ro TX6 modules
Lothar Waßmann
LW at KARO-electronics.de
Thu Dec 12 08:28:00 EST 2013
This patch adds support for the Ka-Ro electronics GmbH TX6 modules.
There are four distinct module types.
Two equipped with an i.MX6Q processor, two with i.MX6DL.
Each of these has either an LVDS display interface or a parallel LCD
interface.
Signed-off-by: Lothar Waßmann <LW at KARO-electronics.de>
---
arch/arm/boot/dts/Makefile | 4 +
arch/arm/boot/dts/imx6dl-tx6u-801x.dts | 350 +++++++++++++++++++++++++
arch/arm/boot/dts/imx6dl-tx6u-811x.dts | 242 ++++++++++++++++++
arch/arm/boot/dts/imx6q-tx6q-101x.dts | 350 +++++++++++++++++++++++++
arch/arm/boot/dts/imx6q-tx6q-111x.dts | 246 ++++++++++++++++++
arch/arm/boot/dts/imx6qdl-tx6.dtsi | 434 ++++++++++++++++++++++++++++++++
6 files changed, 1626 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-801x.dts
create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-811x.dts
create mode 100644 arch/arm/boot/dts/imx6q-tx6q-101x.dts
create mode 100644 arch/arm/boot/dts/imx6q-tx6q-111x.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-tx6.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 535c98f..40175a9 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -152,6 +152,8 @@ dtb-$(CONFIG_ARCH_MXC) += \
imx6dl-gw54xx.dtb \
imx6dl-sabreauto.dtb \
imx6dl-sabresd.dtb \
+ imx6dl-tx6u-801x.dtb \
+ imx6dl-tx6u-811x.dtb \
imx6dl-wandboard.dtb \
imx6q-arm2.dtb \
imx6q-cm-fx6.dtb \
@@ -166,6 +168,8 @@ dtb-$(CONFIG_ARCH_MXC) += \
imx6q-sabrelite.dtb \
imx6q-sabresd.dtb \
imx6q-sbc6x.dtb \
+ imx6q-tx6q-101x.dtb \
+ imx6q-tx6q-111x.dtb \
imx6q-udoo.dtb \
imx6q-wandboard.dtb \
imx6sl-evk.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-801x.dts b/arch/arm/boot/dts/imx6dl-tx6u-801x.dts
new file mode 100644
index 0000000..453a05b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-tx6u-801x.dts
@@ -0,0 +1,350 @@
+/*
+ * Copyright 2013 Lothar Waßmann <LW at KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6DL Module";
+ compatible = "fsl,imx6dl-tx6dl", "fsl,imx6dl";
+
+ aliases {
+ display = &display;
+ lcdif_23bit_pins_a = &pinctrl_disp0_1;
+ lcdif_24bit_pins_a = &pinctrl_disp0_2;
+ };
+
+ backlight at 0 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000>;
+ power-supply = <®_3v3>;
+ /*
+ * a poor man's way to create an inverse 1:1 relationship
+ * between the PWM value and the actual duty cycle
+ */
+ brightness-levels = <100
+ 99 98 97 96 95 94 93 92 91 90
+ 89 88 87 86 85 84 83 82 81 80
+ 79 78 77 76 75 74 73 72 71 70
+ 69 68 67 66 65 64 63 62 61 60
+ 59 58 57 56 55 54 53 52 51 50
+ 49 48 47 46 45 44 43 42 41 40
+ 39 38 37 36 35 34 33 32 31 30
+ 29 28 27 26 25 24 23 22 21 20
+ 19 18 17 16 15 14 13 12 11 10
+ 9 8 7 6 5 4 3 2 1 0>;
+ default-brightness-level = <50>;
+ };
+
+ display: display at di0 {
+ compatible = "fsl,imx-parallel-display";
+ crtcs = <&ipu1 0>;
+ interface-pix-fmt = "rgb24";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_1>;
+ status = "okay";
+
+ display-timings {
+ timing at 0 {
+ panel-name = "VGA";
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ timing at 1 {
+ panel-name = "ETV570";
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ timing at 2 {
+ panel-name = "ET0350";
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ timing at 3 {
+ panel-name = "ET0430";
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ timing at 4 {
+ panel-name = "ET0500";
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ timing at 5 {
+ panel-name = "ET0700"; /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ timing at 6 {
+ panel-name = "ETQ570";
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+
+ regulators {
+ reg_lcd_pwr: regulator at 6 {
+ compatible = "regulator-fixed";
+ regulator-name = "LCD POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ reg_lcd_reset: regulator at 7 {
+ compatible = "regulator-fixed";
+ regulator-name = "LCD RESET";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <300000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+};
+
+&i2c3 {
+ touchscreen: tsc2007 at 48 {
+ compatible = "ti,tsc2007";
+ reg = <0x48>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tsc2007>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <26 0>;
+ gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
+ ti,x-plate-ohms = <660>;
+ linux,wakeup;
+ };
+
+ polytouch: edt-ft5x06 at 38 {
+ compatible = "edt,edt-ft5x06";
+ reg = <0x38>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_edt_ft5x06>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <15 0>;
+ reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&iomuxc {
+ display {
+ pinctrl_disp0_1: disp0grp-1 {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
+ /* PAD DISP0_DAT0 is used for the Flexcan transceiver control */
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
+ >;
+ };
+
+ pinctrl_disp0_2: disp0grp-2 {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
+ >;
+ };
+ };
+
+ kpp {
+ pinctrl_kpp: kppgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__KEY_COL6 0x1b0b1
+ MX6QDL_PAD_GPIO_4__KEY_COL7 0x1b0b1
+ MX6QDL_PAD_KEY_COL2__KEY_COL2 0x1b0b1
+ MX6QDL_PAD_KEY_COL3__KEY_COL3 0x1b0b1
+
+ MX6QDL_PAD_GPIO_2__KEY_ROW6 0x1b0b1
+ MX6QDL_PAD_GPIO_5__KEY_ROW7 0x1b0b1
+ MX6QDL_PAD_KEY_ROW2__KEY_ROW2 0x1b0b1
+ MX6QDL_PAD_KEY_ROW3__KEY_ROW3 0x1b0b1
+ >;
+ };
+ };
+
+ touchpanel {
+ pinctrl_tsc2007: tsc2007grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x1b0b0 /* Interrupt */
+ >;
+ };
+
+ pinctrl_edt_ft5x06: edt-ft5x06grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0 /* Interrupt */
+ MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x1b0b0 /* Reset */
+ MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0 /* Wake */
+ >;
+ };
+ };
+};
+
+&kpp {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_kpp>;
+ status = "okay";
+
+ /* sample keymap */
+ /* row/col 0,1 are mapped to KPP row/col 6,7 */
+ linux,keymap = <
+ 0x06060074 /* row 6, col 6, KEY_POWER */
+ 0x06070052 /* row 6, col 7, KEY_KP0 */
+ 0x0602004f /* row 6, col 2, KEY_KP1 */
+ 0x06030050 /* row 6, col 3, KEY_KP2 */
+ 0x07060051 /* row 7, col 6, KEY_KP3 */
+ 0x0707004b /* row 7, col 7, KEY_KP4 */
+ 0x0702004c /* row 7, col 2, KEY_KP5 */
+ 0x0703004d /* row 7, col 3, KEY_KP6 */
+ 0x02060047 /* row 2, col 6, KEY_KP7 */
+ 0x02070048 /* row 2, col 7, KEY_KP8 */
+ 0x02020049 /* row 2, col 2, KEY_KP9 */
+ >;
+};
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
new file mode 100644
index 0000000..1c4b24e
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
@@ -0,0 +1,242 @@
+/*
+ * Copyright 2013 Lothar Waßmann <LW at KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6DL (LVDS) Module";
+ compatible = "fsl,imx6dl-tx6dl", "fsl,imx6dl";
+
+ aliases {
+ display = &lvds0;
+ lvds0 = &lvds0;
+ lvds1 = &lvds1;
+ };
+
+ backlight at 0 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000>;
+ power-supply = <®_3v3>;
+ brightness-levels = <
+ 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100
+ >;
+ default-brightness-level = <50>;
+ };
+
+ backlight1: pwm-backlight at 1 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 500000>;
+ power-supply = <®_3v3>;
+ brightness-levels = <
+ 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100
+ >;
+ default-brightness-level = <50>;
+ };
+
+
+ regulators {
+ reg_lcd_pwr: regulator at 6 {
+ compatible = "regulator-fixed";
+ regulator-name = "LVDS0 POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ reg_lcd_reset: regulator at 7 {
+ compatible = "regulator-fixed";
+ regulator-name = "LVDS1 POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+ };
+};
+
+&i2c2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+
+ touchscreen2: eeti at 04 {
+ compatible = "eeti,egalax_ts";
+ reg = <0x04>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_eeti_2>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <23 0>;
+ wakeup-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+ linux,wakeup;
+ };
+};
+
+&i2c3 {
+ touchscreen1: eeti at 04 {
+ compatible = "eeti,egalax_ts";
+ reg = <0x04>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_eeti_1>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <22 0>;
+ wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ linux,wakeup;
+ };
+};
+
+&iomuxc {
+ i2c {
+ pinctrl_i2c2: i2c2-grp1 {
+ fsl,pins = <MX6QDL_I2C2_PINGRP2>;
+ };
+ };
+
+ kpp {
+ pinctrl_kpp: kppgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__KEY_COL6 0x1b0b1
+ MX6QDL_PAD_GPIO_4__KEY_COL7 0x1b0b1
+ MX6QDL_PAD_KEY_COL2__KEY_COL2 0x1b0b1
+
+ MX6QDL_PAD_GPIO_2__KEY_ROW6 0x1b0b1
+ MX6QDL_PAD_GPIO_5__KEY_ROW7 0x1b0b1
+ MX6QDL_PAD_KEY_ROW2__KEY_ROW2 0x1b0b1
+ >;
+ };
+ };
+
+ pwm {
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <MX6QDL_PAD_GPIO_9__PWM1_OUT 0x80000000>;
+ };
+ };
+
+ touchpanel {
+ pinctrl_eeti_1: eetigrp-1 {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0xe0 /* Interrupt */
+ >;
+ };
+
+ pinctrl_eeti_2: eetigrp-2 {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D23__GPIO3_IO23 0xe0 /* Interrupt */
+ >;
+ };
+ };
+};
+
+&kpp {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_kpp>;
+ status = "okay";
+
+ /* sample keymap */
+ /* row/col 0,1 are mapped to KPP row/col 6,7
+ * row/col 3 are used for I2C2 (second touch controller on hsd100pxn1)
+ */
+ linux,keymap = <
+ 0x06060074 /* row 6, col 6, KEY_POWER */
+ 0x06070052 /* row 6, col 7, KEY_KP0 */
+ 0x0602004f /* row 6, col 2, KEY_KP1 */
+ 0x07060050 /* row 7, col 6, KEY_KP2 */
+ 0x07070051 /* row 7, col 7, KEY_KP3 */
+ 0x0702004b /* row 7, col 2, KEY_KP4 */
+ 0x0206004c /* row 2, col 6, KEY_KP5 */
+ 0x0207004d /* row 2, col 7, KEY_KP6 */
+ 0x02020047 /* row 2, col 2, KEY_KP7 */
+ >;
+};
+
+&ldb {
+ status = "okay";
+// fsl,dual-channel;
+
+ lvds0: lvds-channel at 0 {
+ fsl,data-mapping = "jeida";
+ fsl,data-width = <24>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&lvds_timing0>;
+ lvds_timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hsync-len = <60>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vsync-len = <10>;
+ vfront-porch = <7>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+
+ lvds1: lvds-channel at 1 {
+ fsl,data-mapping = "jeida";
+ fsl,data-width = <24>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&lvds_timing1>;
+ lvds_timing1: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hsync-len = <60>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vsync-len = <10>;
+ vfront-porch = <7>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-101x.dts b/arch/arm/boot/dts/imx6q-tx6q-101x.dts
new file mode 100644
index 0000000..066bbee
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-tx6q-101x.dts
@@ -0,0 +1,350 @@
+/*
+ * Copyright 2013 Lothar Waßmann <LW at KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6Q Module";
+ compatible = "fsl,imx6q-tx6q", "fsl,imx6q";
+
+ aliases {
+ display = &display;
+ lcdif_23bit_pins_a = &pinctrl_disp0_1;
+ lcdif_24bit_pins_a = &pinctrl_disp0_2;
+ };
+
+ backlight at 0 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000>;
+ power-supply = <®_3v3>;
+ /*
+ * a poor man's way to create an inverse 1:1 relationship
+ * between the PWM value and the actual duty cycle
+ */
+ brightness-levels = <100
+ 99 98 97 96 95 94 93 92 91 90
+ 89 88 87 86 85 84 83 82 81 80
+ 79 78 77 76 75 74 73 72 71 70
+ 69 68 67 66 65 64 63 62 61 60
+ 59 58 57 56 55 54 53 52 51 50
+ 49 48 47 46 45 44 43 42 41 40
+ 39 38 37 36 35 34 33 32 31 30
+ 29 28 27 26 25 24 23 22 21 20
+ 19 18 17 16 15 14 13 12 11 10
+ 9 8 7 6 5 4 3 2 1 0>;
+ default-brightness-level = <50>;
+ };
+
+ display: display at di0 {
+ compatible = "fsl,imx-parallel-display";
+ crtcs = <&ipu1 0>;
+ interface-pix-fmt = "rgb24";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_1>;
+ status = "okay";
+
+ display-timings {
+ timing at 0 {
+ panel-name = "VGA";
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ timing at 1 {
+ panel-name = "ETV570";
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ timing at 2 {
+ panel-name = "ET0350";
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ timing at 3 {
+ panel-name = "ET0430";
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ timing at 4 {
+ panel-name = "ET0500";
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ timing at 5 {
+ panel-name = "ET0700"; /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ timing at 6 {
+ panel-name = "ETQ570";
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+
+ regulators {
+ reg_lcd_pwr: regulator at 6 {
+ compatible = "regulator-fixed";
+ regulator-name = "LCD POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ reg_lcd_reset: regulator at 7 {
+ compatible = "regulator-fixed";
+ regulator-name = "LCD RESET";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <300000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+};
+
+&i2c3 {
+ touchscreen: tsc2007 at 48 {
+ compatible = "ti,tsc2007";
+ reg = <0x48>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tsc2007>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <26 0>;
+ gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
+ ti,x-plate-ohms = <660>;
+ linux,wakeup;
+ };
+
+ polytouch: edt-ft5x06 at 38 {
+ compatible = "edt,edt-ft5x06";
+ reg = <0x38>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_edt_ft5x06>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <15 0>;
+ reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&iomuxc {
+ display {
+ pinctrl_disp0_1: disp0grp-1 {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
+ /* PAD DISP0_DAT0 is used for the Flexcan transceiver control */
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
+ >;
+ };
+
+ pinctrl_disp0_2: disp0grp-2 {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
+ >;
+ };
+ };
+
+ kpp {
+ pinctrl_kpp: kppgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__KEY_COL6 0x1b0b1
+ MX6QDL_PAD_GPIO_4__KEY_COL7 0x1b0b1
+ MX6QDL_PAD_KEY_COL2__KEY_COL2 0x1b0b1
+ MX6QDL_PAD_KEY_COL3__KEY_COL3 0x1b0b1
+
+ MX6QDL_PAD_GPIO_2__KEY_ROW6 0x1b0b1
+ MX6QDL_PAD_GPIO_5__KEY_ROW7 0x1b0b1
+ MX6QDL_PAD_KEY_ROW2__KEY_ROW2 0x1b0b1
+ MX6QDL_PAD_KEY_ROW3__KEY_ROW3 0x1b0b1
+ >;
+ };
+ };
+
+ touchpanel {
+ pinctrl_tsc2007: tsc2007grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x1b0b0 /* Interrupt */
+ >;
+ };
+
+ pinctrl_edt_ft5x06: edt-ft5x06grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0 /* Interrupt */
+ MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x1b0b0 /* Reset */
+ MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0 /* Wake */
+ >;
+ };
+ };
+};
+
+&kpp {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_kpp>;
+ status = "okay";
+
+ /* sample keymap */
+ /* row/col 0,1 are mapped to KPP row/col 6,7 */
+ linux,keymap = <
+ 0x06060074 /* row 6, col 6, KEY_POWER */
+ 0x06070052 /* row 6, col 7, KEY_KP0 */
+ 0x0602004f /* row 6, col 2, KEY_KP1 */
+ 0x06030050 /* row 6, col 3, KEY_KP2 */
+ 0x07060051 /* row 7, col 6, KEY_KP3 */
+ 0x0707004b /* row 7, col 7, KEY_KP4 */
+ 0x0702004c /* row 7, col 2, KEY_KP5 */
+ 0x0703004d /* row 7, col 3, KEY_KP6 */
+ 0x02060047 /* row 2, col 6, KEY_KP7 */
+ 0x02070048 /* row 2, col 7, KEY_KP8 */
+ 0x02020049 /* row 2, col 2, KEY_KP9 */
+ >;
+};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-111x.dts b/arch/arm/boot/dts/imx6q-tx6q-111x.dts
new file mode 100644
index 0000000..102666a
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-tx6q-111x.dts
@@ -0,0 +1,246 @@
+/*
+ * Copyright 2013 Lothar Waßmann <LW at KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6Q (LVDS) Module";
+ compatible = "fsl,imx6q-tx6q", "fsl,imx6q";
+
+ aliases {
+ display = &lvds0;
+ lvds0 = &lvds0;
+ lvds1 = &lvds1;
+ };
+
+ backlight at 0 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000>;
+ power-supply = <®_3v3>;
+ brightness-levels = <
+ 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100
+ >;
+ default-brightness-level = <50>;
+ };
+
+ backlight1: pwm-backlight at 1 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 500000>;
+ power-supply = <®_3v3>;
+ brightness-levels = <
+ 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100
+ >;
+ default-brightness-level = <50>;
+ };
+
+
+ regulators {
+ reg_lcd_pwr: regulator at 6 {
+ compatible = "regulator-fixed";
+ regulator-name = "LVDS0 POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ reg_lcd_reset: regulator at 7 {
+ compatible = "regulator-fixed";
+ regulator-name = "LVDS1 POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+ };
+};
+
+&i2c2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+
+ touchscreen2: eeti at 04 {
+ compatible = "eeti,egalax_ts";
+ reg = <0x04>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_eeti_2>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <23 0>;
+ wakeup-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+ linux,wakeup;
+ };
+};
+
+&i2c3 {
+ touchscreen1: eeti at 04 {
+ compatible = "eeti,egalax_ts";
+ reg = <0x04>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_eeti_1>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <22 0>;
+ wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ linux,wakeup;
+ };
+};
+
+&iomuxc {
+ i2c {
+ pinctrl_i2c2: i2c2-grp1 {
+ fsl,pins = <MX6QDL_I2C2_PINGRP2>;
+ };
+ };
+
+ kpp {
+ pinctrl_kpp: kppgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__KEY_COL6 0x1b0b1
+ MX6QDL_PAD_GPIO_4__KEY_COL7 0x1b0b1
+ MX6QDL_PAD_KEY_COL2__KEY_COL2 0x1b0b1
+
+ MX6QDL_PAD_GPIO_2__KEY_ROW6 0x1b0b1
+ MX6QDL_PAD_GPIO_5__KEY_ROW7 0x1b0b1
+ MX6QDL_PAD_KEY_ROW2__KEY_ROW2 0x1b0b1
+ >;
+ };
+ };
+
+ pwm {
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <MX6QDL_PAD_GPIO_9__PWM1_OUT 0x80000000>;
+ };
+ };
+
+ touchpanel {
+ pinctrl_eeti_1: eetigrp-1 {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0xe0 /* Interrupt */
+ >;
+ };
+
+ pinctrl_eeti_2: eetigrp-2 {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D23__GPIO3_IO23 0xe0 /* Interrupt */
+ >;
+ };
+ };
+};
+
+&kpp {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_kpp>;
+ status = "okay";
+
+ /* sample keymap */
+ /* row/col 0,1 are mapped to KPP row/col 6,7
+ * row/col 3 are used for I2C2 (second touch controller on hsd100pxn1)
+ */
+ linux,keymap = <
+ 0x06060074 /* row 6, col 6, KEY_POWER */
+ 0x06070052 /* row 6, col 7, KEY_KP0 */
+ 0x0602004f /* row 6, col 2, KEY_KP1 */
+ 0x07060050 /* row 7, col 6, KEY_KP2 */
+ 0x07070051 /* row 7, col 7, KEY_KP3 */
+ 0x0702004b /* row 7, col 2, KEY_KP4 */
+ 0x0206004c /* row 2, col 6, KEY_KP5 */
+ 0x0207004d /* row 2, col 7, KEY_KP6 */
+ 0x02020047 /* row 2, col 2, KEY_KP7 */
+ >;
+};
+
+&ldb {
+ status = "okay";
+// fsl,dual-channel;
+
+ lvds0: lvds-channel at 0 {
+ fsl,data-mapping = "jeida";
+ fsl,data-width = <24>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&lvds_timing0>;
+ lvds_timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hsync-len = <60>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vsync-len = <10>;
+ vfront-porch = <7>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+
+ lvds1: lvds-channel at 1 {
+ fsl,data-mapping = "jeida";
+ fsl,data-width = <24>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&lvds_timing1>;
+ lvds_timing1: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hsync-len = <60>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vsync-len = <10>;
+ vfront-porch = <7>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+};
+
+&sata {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
new file mode 100644
index 0000000..af315db
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
@@ -0,0 +1,434 @@
+/*
+ * Copyright 2013 Lothar Waßmann <LW at KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ aliases {
+ can0 = &can1;
+ can1 = &can2;
+ ethernet0 = &fec;
+ reg_can_xcvr = ®_can_xcvr;
+ stk5led = &user_led;
+ usbotg = &usbotg;
+ };
+
+ chosen {
+ };
+
+ memory {
+ reg = <0 0>; /* will be filled by U-Boot */
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ mclk: codec_clock {
+ compatible = "fixed-clock";
+ reg = <0>;
+ #clock-cells = <0>;
+ clock-frequency = <27000000>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+ linux,code = <116>; /* KEY_POWER */
+ gpio-key,wakeup;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_led>;
+
+ user_led: user {
+ label = "Heartbeat";
+ gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+
+ reg_3v3_etn: regulator at 0 {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3_ETN";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_2v5: regulator at 1 {
+ compatible = "regulator-fixed";
+ regulator-name = "2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ };
+
+ reg_3v3: regulator at 2 {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_can_xcvr: regulator at 3 {
+ compatible = "regulator-fixed";
+ regulator-name = "CAN XCVR";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
+ enable-active-low;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan_xcvr>;
+ };
+
+ reg_usbh1_vbus: regulator at 4 {
+ compatible = "regulator-fixed";
+ regulator-name = "usbh1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1_vbus>;
+ gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usbotg_vbus: regulator at 5 {
+ compatible = "regulator-fixed";
+ regulator-name = "usbotg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg_vbus>;
+ gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+ };
+
+ sound {
+ compatible = "fsl,imx6qdl-tx6qdl-sgtl5000",
+ "fsl,imx-audio-sgtl5000";
+ model = "sgtl5000-audio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ ssi-controller = <&ssi1>;
+ audio-codec = <&sgtl5000>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ mux-int-port = <1>;
+ mux-ext-port = <5>;
+ };
+};
+
+&audmux {
+ status = "okay";
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ xceiver-supply = <®_can_xcvr>;
+
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ xceiver-supply = <®_can_xcvr>;
+
+ status = "okay";
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ fsl,spi-num-chipselects = <2>;
+ cs-gpios = <
+ &gpio2 30 GPIO_ACTIVE_HIGH
+ &gpio3 19 GPIO_ACTIVE_HIGH
+ >;
+ status = "okay";
+
+ spidev at 0 {
+ compatible = "spidev";
+ reg = <0>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_HIGH>;
+ phy-supply = <®_3v3_etn>;
+ status = "okay";
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ nand-on-flash-bbt;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ ds1339: rtc at 68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ };
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ sgtl5000: sgtl5000 at 0a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ VDDA-supply = <®_2v5>;
+ VDDIO-supply = <®_3v3>;
+ clocks = <&mclk>;
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ audmux {
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <MX6QDL_AUDMUX_PINGRP5>;
+ };
+ };
+
+ enet {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <MX6QDL_ENET_PINGRP4>;
+ };
+ };
+
+ flexcan {
+ pinctrl_flexcan1: flexcan1grp {
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ };
+
+ pinctrl_flexcan_xcvr: flexcan-xcvrgrp {
+ fsl,pins = <MX6QDL_PAD_DISP0_DAT0__GPIO4_IO21 0x1b0b0>; /* Flexcan XCVR enable */
+ };
+ };
+
+ hog {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b1 /* LED */
+ MX6QDL_PAD_SD3_DAT2__GPIO7_IO06 0x1b0b1 /* ETN PHY RESET */
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1 /* ETN PHY POWER */
+ MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1b0b1 /* ETN PHY INT
+ MX6QDL_PAD_SD3_CMD__GPIO7_IO02 0x1b0b0 /* SD1 CD */
+ MX6QDL_PAD_SD3_CLK__GPIO7_IO03 0x1b0b0 /* SD2 CD */
+ MX6QDL_PAD_EIM_EB3__GPIO2_IO31 0x1b0b1 /* LCD Power Enable */
+ MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b1 /* LCD Reset */
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b1 /* PWR BTN */
+ >;
+ };
+ };
+
+ i2c {
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <MX6QDL_I2C1_PINGRP1>;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <MX6QDL_I2C3_PINGRP2>;
+ };
+ };
+
+ led {
+ pinctrl_led: ledgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b1 /* LED */
+ >;
+ };
+ };
+
+ nand {
+ pinctrl_gpmi_nand: gpmi-nand {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ >;
+ };
+ };
+
+ pwm {
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <MX6QDL_PAD_GPIO_1__PWM2_OUT 0xb0b1>;
+ };
+ };
+
+ ecspi {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <MX6QDL_ECSPI1_PINGRP1
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b1
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b0b1
+ MX6QDL_PAD_GPIO_19__ECSPI1_RDY 0x1b0b1
+ >;
+ };
+ };
+
+ uart {
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <MX6QDL_UART1_PINGRP2
+ MX6QDL_PAD_SD3_DAT0__UART1_CTS_B 0x1b0b1
+ MX6QDL_PAD_SD3_DAT1__UART1_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <MX6QDL_UART2_PINGRP3
+ MX6QDL_PAD_SD4_DAT6__UART2_CTS_B 0x1b0b1
+ MX6QDL_PAD_SD4_DAT5__UART2_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <MX6QDL_UART3_PINGRP3
+ MX6QDL_PAD_SD3_DAT3__UART3_CTS_B 0x1b0b1
+ MX6QDL_PAD_SD3_RST__UART3_RTS_B 0x1b0b1
+ >;
+ };
+ };
+
+ usbh1 {
+ pinctrl_usbh1_vbus: usbh1-vbusgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0 /* USBH1_VBUSEN */
+ >;
+ };
+ };
+
+ usbotg {
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x17059
+ >;
+ };
+
+ pinctrl_usbotg_vbus: usbotg-vbusgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0 /* USBOTG_VBUSEN */
+ >;
+ };
+ };
+
+ usdhc {
+ pinctrl_usdhc1: ussdhc1grp {
+ fsl,pins = <MX6QDL_USDHC1_PINGRP_D4_200MHZ>;
+ };
+
+ pinctrl_usdhc2: ussdhc2grp {
+ fsl,pins = <MX6QDL_USDHC2_PINGRP_D4_200MHZ>;
+ };
+ };
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&ssi1 {
+ fsl,mode = "i2s-slave";
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usbh1_vbus>;
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usbotg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ dr_mode = "peripheral";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio7 2 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ cd-gpios = <&gpio7 3 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
--
1.7.2.5
More information about the linux-arm-kernel
mailing list