[PATCH V2 2/2] ARM: dts: Enable ahci sata and sata phy
Yuvaraj Kumar
yuvaraj.cd at gmail.com
Tue Dec 10 03:56:52 EST 2013
On Mon, Nov 25, 2013 at 12:01 PM, Kishon Vijay Abraham I <kishon at ti.com> wrote:
> Hi,
>
> On Monday 11 November 2013 02:02 PM, Yuvaraj Kumar C D wrote:
>> This patch adds dt entry for ahci sata controller and its
>> corresponding phy controller.phy node has been added w.r.t
>> new generic phy framework.
>>
>> Changes since V1:
>> 1.Minor changes to node name convention
>> 2.Updated binding document.
>>
>> Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd at samsung.com>
>> ---
>> .../devicetree/bindings/ata/exynos-sata-phy.txt | 19 +++++++++++++-----
>> .../devicetree/bindings/ata/exynos-sata.txt | 17 +++++++++++-----
>> arch/arm/boot/dts/exynos5250-arndale.dts | 9 ++++++++-
>> arch/arm/boot/dts/exynos5250-smdk5250.dts | 8 ++------
>> arch/arm/boot/dts/exynos5250.dtsi | 21 ++++++++++++++++----
>> 5 files changed, 53 insertions(+), 21 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt b/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt
>> index 37824fa..a679e17 100644
>> --- a/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt
>> +++ b/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt
>> @@ -4,11 +4,20 @@ SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers.
>> Each SATA PHY controller should have its own node.
>>
>> Required properties:
>> -- compatible : compatible list, contains "samsung,exynos5-sata-phy"
>> +- compatible : compatible list, contains "samsung,exynos5250-sata-phy"
>
> What if someone is already using samsung,exynos5-sata-phy? You can mark the old
> one as deprecated and add the new compatible string.
AFAIK, there is no driver using it.In the initial version of sata phy
driver,only the DT part has been merged.So it was there
without any user.
>> - reg : <registers mapping>
>>
>> Example:
>> - sata at ffe07000 {
>> - compatible = "samsung,exynos5-sata-phy";
>> - reg = <0xffe07000 0x1000>;
>> - };
>> + sata_phy: sata-phy at 12170000 {
>> + compatible = "samsung,exynos5250-sata-phy";
>> + reg = <0x12170000 0x1ff>;
>> + clocks = <&clock 287>;
>> + clock-names = "sata_phyctrl";
>> + #phy-cells = <0>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> + sataphy-pmu {
>> + reg = <0x10040724 0x4>;
>> + };
>
> alignment problem..
ok
>> + };
>> diff --git a/Documentation/devicetree/bindings/ata/exynos-sata.txt b/Documentation/devicetree/bindings/ata/exynos-sata.txt
>> index 0849f10..8ec7327 100644
>> --- a/Documentation/devicetree/bindings/ata/exynos-sata.txt
>> +++ b/Documentation/devicetree/bindings/ata/exynos-sata.txt
>> @@ -8,10 +8,17 @@ Required properties:
>> - interrupts : <interrupt mapping for SATA IRQ>
>> - reg : <registers mapping>
>> - samsung,sata-freq : <frequency in MHz>
>> +- phys : as mentioned in phy-bindings.txt
>> +- phy-names : as mentioned in phy-bindings.txt
>>
>> Example:
>> - sata at ffe08000 {
>> - compatible = "samsung,exynos5-sata";
>> - reg = <0xffe08000 0x1000>;
>> - interrupts = <115>;
>> - };
>> + sata at 122F0000 {
>
> use lower case here..
ok
>> + compatible = "snps,dwc-ahci";
>> + samsung,sata-freq = <66>;
>> + reg = <0x122F0000 0x1ff>;
> here too..
ok
>> + interrupts = <0 115 0>;
>> + clocks = <&clock 277>, <&clock 143>;
>> + clock-names = "sata", "sclk_sata";
>> + phys = <&sata_phy>;
>> + phy-names = "sata-phy";
>> + };
>> diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
>> index b77a37e..434e4f3 100644
>> --- a/arch/arm/boot/dts/exynos5250-arndale.dts
>> +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
>> @@ -381,7 +381,14 @@
>> };
>>
>> i2c at 121D0000 {
>> - status = "disabled";
>> + samsung,i2c-sda-delay = <100>;
>> + samsung,i2c-max-bus-freq = <40000>;
>> + samsung,i2c-slave-addr = <0x38>;
>> +
>> + sata-phy {
>> + compatible = "sata-phy-i2c";
>
> Do you have documentation for this compatible string?
Sorry missed that.I will add in the next version.
>> + reg = <0x38>;
>> + };
>> };
>>
>> mmc_0: mmc at 12200000 {
>> diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/exynos5250-smdk5250.dts
>> index 13746df..eeeeef9 100644
>> --- a/arch/arm/boot/dts/exynos5250-smdk5250.dts
>> +++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts
>> @@ -90,16 +90,12 @@
>> samsung,i2c-max-bus-freq = <40000>;
>> samsung,i2c-slave-addr = <0x38>;
>>
>> - sata-phy {
>> - compatible = "samsung,sata-phy";
>> + sata-phy at 38 {
>> + compatible = "sata-phy-i2c";
>> reg = <0x38>;
>> };
>> };
>>
>> - sata at 122F0000 {
>> - samsung,sata-freq = <66>;
>> - };
>> -
>> i2c at 12C80000 {
>> samsung,i2c-sda-delay = <100>;
>> samsung,i2c-max-bus-freq = <66000>;
>> diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi
>> index 80b5df5..d24db31 100644
>> --- a/arch/arm/boot/dts/exynos5250.dtsi
>> +++ b/arch/arm/boot/dts/exynos5250.dtsi
>> @@ -46,6 +46,7 @@
>> i2c6 = &i2c_6;
>> i2c7 = &i2c_7;
>> i2c8 = &i2c_8;
>> + i2c9 = &i2c_9;
>> pinctrl0 = &pinctrl_0;
>> pinctrl1 = &pinctrl_1;
>> pinctrl2 = &pinctrl_2;
>> @@ -216,16 +217,28 @@
>> };
>>
>> sata at 122F0000 {
>> - compatible = "samsung,exynos5-sata-ahci";
>> + compatible = "snps,dwc-ahci";
>> + samsung,sata-freq = <66>;
>> reg = <0x122F0000 0x1ff>;
>> interrupts = <0 115 0>;
>> clocks = <&clock 277>, <&clock 143>;
>> clock-names = "sata", "sclk_sata";
>> + phys = <&sata_phy>;
>> + phy-names = "sata-phy";
>> };
>>
>> - sata-phy at 12170000 {
>> - compatible = "samsung,exynos5-sata-phy";
>> + sata_phy: sata-phy at 12170000 {
>> + compatible = "samsung,exynos5250-sata-phy";
>> reg = <0x12170000 0x1ff>;
>> + clocks = <&clock 287>;
>> + clock-names = "sata_phyctrl";
>> + #phy-cells = <0>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> + sataphy-pmu {
>> + reg = <0x10040724 0x4>;
>> + };
>
> alignment problem here..
Ok
>
> Thanks
> Kishon
More information about the linux-arm-kernel
mailing list