[PATCH 2/2] ARM: sun6i: dt: Fix interrupt trigger types

[Maxime Ripard]

The Allwinner A31 uses the ARM GIC as its internal interrupts controller. The
GIC can work on several interrupt triggers, and the A31 was actually setting it
up to use a rising edge as a trigger, while it was actually a level high
trigger, leading to some interrupts that would be completely ignored if the
edge was missed.

Signed-off-by: Maxime Ripard <maxime.ripard at free-electrons.com>
Reported-by: Hans de Goede <hdegoede at redhat.com>
---
 arch/arm/boot/dts/sun6i-a31.dtsi | 27 +++++++++++++++------------
 1 file changed, 15 insertions(+), 12 deletions(-)

diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi
index c1751a6..7f5878c 100644
--- a/arch/arm/boot/dts/sun6i-a31.dtsi
+++ b/arch/arm/boot/dts/sun6i-a31.dtsi
@@ -193,7 +193,10 @@
 		pio: pinctrl at 01c20800 {
 			compatible = "allwinner,sun6i-a31-pinctrl";
 			reg = <0x01c20800 0x400>;
-			interrupts = <0 11 1>, <0 15 1>, <0 16 1>, <0 17 1>;
+			interrupts = <0 11 4>,
+				     <0 15 4>,
+				     <0 16 4>,
+				     <0 17 4>;
 			clocks = <&apb1_gates 5>;
 			gpio-controller;
 			interrupt-controller;
@@ -212,11 +215,11 @@
 		timer at 01c20c00 {
 			compatible = "allwinner,sun4i-timer";
 			reg = <0x01c20c00 0xa0>;
-			interrupts = <0 18 1>,
-				     <0 19 1>,
-				     <0 20 1>,
-				     <0 21 1>,
-				     <0 22 1>;
+			interrupts = <0 18 4>,
+				     <0 19 4>,
+				     <0 20 4>,
+				     <0 21 4>,
+				     <0 22 4>;
 			clocks = <&osc24M>;
 		};
 
@@ -228,7 +231,7 @@
 		uart0: serial at 01c28000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28000 0x400>;
-			interrupts = <0 0 1>;
+			interrupts = <0 0 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb2_gates 16>;
@@ -238,7 +241,7 @@
 		uart1: serial at 01c28400 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28400 0x400>;
-			interrupts = <0 1 1>;
+			interrupts = <0 1 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb2_gates 17>;
@@ -248,7 +251,7 @@
 		uart2: serial at 01c28800 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28800 0x400>;
-			interrupts = <0 2 1>;
+			interrupts = <0 2 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb2_gates 18>;
@@ -258,7 +261,7 @@
 		uart3: serial at 01c28c00 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28c00 0x400>;
-			interrupts = <0 3 1>;
+			interrupts = <0 3 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb2_gates 19>;
@@ -268,7 +271,7 @@
 		uart4: serial at 01c29000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c29000 0x400>;
-			interrupts = <0 4 1>;
+			interrupts = <0 4 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb2_gates 20>;
@@ -278,7 +281,7 @@
 		uart5: serial at 01c29400 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c29400 0x400>;
-			interrupts = <0 5 1>;
+			interrupts = <0 5 4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&apb2_gates 21>;
-- 
1.8.4.2