[PATCH v2 02/11] arm: pxa27x: support ICP DAS LP-8x4x
Sergei Ianovich
ynvich at gmail.com
Fri Dec 6 11:48:58 EST 2013
ICP DAS calls LP-8x4x 'programmable automation controller'. It is
an industrial computer based on PXA270 SoC. They ship it with a 2.6.19
kernel and proprietary kernel module and userspace library to access
its industrial IO.
This patch allows to boot the device with a modern kernel. It adds
support for:
* FPGA irq chip
* MMC card interface on PXA270
* USB 1.1 port on PXA270
* 2 NOR flash devices
* VGA interface on PXA270
* 2 onboard ethernet Davicom DM9000 devices
* 3 serial UART ports on PXA270
Support for these devices will be added in separate patches, since
they are not currently supported by the kernel:
* DS1302 RTC
* 512kiB SRAM
* 3 built-in and up to 32 pluggable 8250 serial UART ports
* industrial IO parallel bus
* digital and analog industrial IO modules for parallel bus
* serial interface for digital and analog industrial IO modules on
parallel bus
Signed-off-by: Sergei Ianovich <ynvich at gmail.com>
CC: Arnd Bergmann <arnd at arndb.de>
---
changes v1..v2
* clean up defconfig (reduces size by 10) as suggested
by Arnd Bergmann
* fixed constant address definition to include (void *) cast
as suggested by Arnd Bergmann
* moved fixed virtual addresses into the machine source file.
Header file is dropped.
* static platform devices are replaced by dynamically allocated
as suggested by Arnd Bergmann
arch/arm/configs/lp8x4x_defconfig | 235 +++++++++++++++++++
arch/arm/mach-pxa/Kconfig | 16 ++
arch/arm/mach-pxa/Makefile | 1 +
arch/arm/mach-pxa/lp8x4x.c | 473 ++++++++++++++++++++++++++++++++++++++
4 files changed, 725 insertions(+)
create mode 100644 arch/arm/configs/lp8x4x_defconfig
create mode 100644 arch/arm/mach-pxa/lp8x4x.c
diff --git a/arch/arm/configs/lp8x4x_defconfig b/arch/arm/configs/lp8x4x_defconfig
new file mode 100644
index 0000000..2612e60
--- /dev/null
+++ b/arch/arm/configs/lp8x4x_defconfig
@@ -0,0 +1,235 @@
+CONFIG_CROSS_COMPILE="arm-linux-gnueabi-"
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_RCU_BOOST=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_NAMESPACES=y
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+# CONFIG_UID16 is not set
+# CONFIG_SHMEM is not set
+CONFIG_EMBEDDED=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLOB=y
+CONFIG_JUMP_LABEL=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+# CONFIG_LBDAF is not set
+CONFIG_BLK_CMDLINE_PARSER=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+CONFIG_LDM_PARTITION=y
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_ARCH_PXA=y
+CONFIG_MACH_LP8X4X=y
+# CONFIG_ARM_THUMB is not set
+CONFIG_PREEMPT=y
+CONFIG_AEABI=y
+# CONFIG_COMPACTION is not set
+# CONFIG_CROSS_MEMORY_ATTACH is not set
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="init=/sbin/init root=/dev/mmcblk0p1 rw rootfstype=ext4 console=ttyS0,115200 mem=128M rootwait"
+# CONFIG_SUSPEND is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_BRIDGE=m
+CONFIG_BRIDGE_VLAN_FILTERING=y
+CONFIG_VLAN_8021Q=m
+CONFIG_VLAN_8021Q_GVRP=y
+CONFIG_VLAN_8021Q_MVRP=y
+# CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_FW_LOADER is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+CONFIG_MTD_CFI_GEOMETRY=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_PXA2XX=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_LOOP_MIN_COUNT=2
+CONFIG_SCSI=y
+# CONFIG_SCSI_PROC_FS is not set
+CONFIG_BLK_DEV_SD=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+CONFIG_BONDING=m
+CONFIG_MACVLAN=m
+CONFIG_MACVTAP=m
+CONFIG_TUN=m
+# CONFIG_NET_VENDOR_ARC is not set
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+CONFIG_DM9000=y
+CONFIG_DM9000_FORCE_SIMPLE_PHY_POLL=y
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_PPP=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPPOE=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_SLIP=m
+CONFIG_SLIP_COMPRESSED=y
+# CONFIG_WLAN is not set
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=800
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=600
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+# CONFIG_DEVKMEM is not set
+CONFIG_SERIAL_8250=y
+# CONFIG_SERIAL_8250_DEPRECATED_OPTIONS is not set
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=40
+CONFIG_SERIAL_8250_RUNTIME_UARTS=40
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_MANY_PORTS=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_SERIAL_PXA=y
+CONFIG_HW_RANDOM=y
+CONFIG_I2C=m
+# CONFIG_I2C_COMPAT is not set
+CONFIG_I2C_PXA=m
+CONFIG_I2C_PXA_SLAVE=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_SA1100_WATCHDOG=m
+CONFIG_FB=y
+CONFIG_FB_PXA=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+CONFIG_HID_GENERIC=m
+CONFIG_HID_A4TECH=m
+CONFIG_HID_CYPRESS=m
+CONFIG_HID_KEYTOUCH=m
+CONFIG_HID_KENSINGTON=m
+CONFIG_HID_LOGITECH=m
+CONFIG_HID_MICROSOFT=m
+CONFIG_HID_MONTEREY=m
+CONFIG_USB_HIDDEV=y
+CONFIG_I2C_HID=m
+CONFIG_USB=m
+CONFIG_USB_OHCI_HCD=m
+CONFIG_USB_ACM=m
+CONFIG_USB_PRINTER=m
+CONFIG_USB_STORAGE=m
+CONFIG_USB_STORAGE_REALTEK=m
+CONFIG_USB_STORAGE_DATAFAB=m
+CONFIG_USB_STORAGE_FREECOM=m
+CONFIG_USB_STORAGE_ISD200=m
+CONFIG_USB_STORAGE_USBAT=m
+CONFIG_USB_STORAGE_SDDR09=m
+CONFIG_USB_STORAGE_SDDR55=m
+CONFIG_USB_STORAGE_JUMPSHOT=m
+CONFIG_USB_STORAGE_ALAUDA=m
+CONFIG_USB_STORAGE_ONETOUCH=m
+CONFIG_USB_STORAGE_KARMA=m
+CONFIG_USB_STORAGE_CYPRESS_ATACB=m
+CONFIG_USB_STORAGE_ENE_UB6250=m
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_SIMPLE=m
+CONFIG_USB_SERIAL_AIRCABLE=m
+CONFIG_USB_SERIAL_ARK3116=m
+CONFIG_USB_SERIAL_BELKIN=m
+CONFIG_USB_SERIAL_CH341=m
+CONFIG_USB_SERIAL_WHITEHEAT=m
+CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
+CONFIG_USB_SERIAL_CP210X=m
+CONFIG_USB_SERIAL_CYPRESS_M8=m
+CONFIG_USB_SERIAL_EMPEG=m
+CONFIG_USB_SERIAL_FTDI_SIO=m
+CONFIG_USB_SERIAL_VISOR=m
+CONFIG_USB_SERIAL_IPAQ=m
+CONFIG_USB_SERIAL_IR=m
+CONFIG_USB_SERIAL_EDGEPORT=m
+CONFIG_USB_SERIAL_EDGEPORT_TI=m
+CONFIG_USB_SERIAL_F81232=m
+CONFIG_USB_SERIAL_GARMIN=m
+CONFIG_USB_SERIAL_IPW=m
+CONFIG_USB_SERIAL_IUU=m
+CONFIG_USB_SERIAL_KEYSPAN_PDA=m
+CONFIG_USB_SERIAL_KEYSPAN=m
+CONFIG_USB_SERIAL_KLSI=m
+CONFIG_USB_SERIAL_KOBIL_SCT=m
+CONFIG_USB_SERIAL_MCT_U232=m
+CONFIG_USB_SERIAL_METRO=m
+CONFIG_USB_SERIAL_MOS7720=m
+CONFIG_USB_SERIAL_MOS7840=m
+CONFIG_USB_SERIAL_NAVMAN=m
+CONFIG_USB_SERIAL_PL2303=m
+CONFIG_USB_SERIAL_OTI6858=m
+CONFIG_USB_SERIAL_QCAUX=m
+CONFIG_USB_SERIAL_QUALCOMM=m
+CONFIG_USB_SERIAL_SPCP8X5=m
+CONFIG_USB_SERIAL_SAFE=m
+CONFIG_USB_SERIAL_SAFE_PADDED=y
+CONFIG_USB_SERIAL_SIERRAWIRELESS=m
+CONFIG_USB_SERIAL_SYMBOL=m
+CONFIG_USB_SERIAL_TI=m
+CONFIG_USB_SERIAL_CYBERJACK=m
+CONFIG_USB_SERIAL_XIRCOM=m
+CONFIG_USB_SERIAL_OPTION=m
+CONFIG_USB_SERIAL_OMNINET=m
+CONFIG_USB_SERIAL_OPTICON=m
+CONFIG_USB_SERIAL_XSENS_MT=m
+CONFIG_USB_SERIAL_WISHBONE=m
+CONFIG_USB_SERIAL_ZTE=m
+CONFIG_USB_SERIAL_SSU100=m
+CONFIG_USB_SERIAL_QT2=m
+CONFIG_MMC=y
+CONFIG_MMC_PXA=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_PXA=m
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT2_FS=m
+CONFIG_EXT3_FS=y
+CONFIG_EXT4_FS=y
+CONFIG_REISERFS_FS=m
+CONFIG_ISO9660_FS=m
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_NTFS_FS=m
+CONFIG_NTFS_RW=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
+CONFIG_CIFS=m
+CONFIG_CIFS_STATS=y
+CONFIG_CODA_FS=m
+CONFIG_NLS_DEFAULT="cp1251"
+CONFIG_NLS_CODEPAGE_1251=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_PRINTK_TIME=y
diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig
index 96100db..efaf2d0 100644
--- a/arch/arm/mach-pxa/Kconfig
+++ b/arch/arm/mach-pxa/Kconfig
@@ -273,6 +273,22 @@ config MACH_VPAC270
comment "End-user Products (sorted by vendor name)"
+config MACH_LP8X4X
+ bool "ICP DAS LP-8X4X"
+ select IWMMXT
+ select PXA27x
+ help
+ Say Y here if you intend to run this kernel on an ICP DAS
+ LP-8x4x programmable automation controller.
+
+ LP-8x4x is ARM-based and built around PXA270 SoC. The device
+ has 128 MiB SDRAM, 48 or 96 MiB NOR flash, VGA port with
+ 800x600 resolution, MMC card slot, 2 Ethernet ports, 1 USB
+ port, 5 serial ports (1 on them is wired internally to
+ expansion slots). The device has a range of digital and
+ analog expansion IO modules which can be installed in 1, 4 or
+ 8 slots depending on the model.
+
config MACH_H4700
bool "HP iPAQ hx4700"
select HAVE_PWM
diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile
index 648867a..b264325 100644
--- a/arch/arm/mach-pxa/Makefile
+++ b/arch/arm/mach-pxa/Makefile
@@ -63,6 +63,7 @@ obj-$(CONFIG_MACH_COLIBRI320) += colibri-pxa3xx.o colibri-pxa320.o
obj-$(CONFIG_MACH_VPAC270) += vpac270.o
# End-user Products
+obj-$(CONFIG_MACH_LP8X4X) += lp8x4x.o
obj-$(CONFIG_MACH_H4700) += hx4700.o
obj-$(CONFIG_MACH_H5000) += h5000.o
obj-$(CONFIG_MACH_HIMALAYA) += himalaya.o
diff --git a/arch/arm/mach-pxa/lp8x4x.c b/arch/arm/mach-pxa/lp8x4x.c
new file mode 100644
index 0000000..0d3d8c0
--- /dev/null
+++ b/arch/arm/mach-pxa/lp8x4x.c
@@ -0,0 +1,473 @@
+/*
+ * linux/arch/arm/mach-pxa/lp8x4x.c
+ *
+ * Support for ICP DAS LP-8x4x programmable automation controller
+ * Copyright (C) 2013 Sergei Ianovich <ynvich at gmail.com>
+ *
+ * borrowed heavily from
+ * Support for the Intel HCDDBBVA0 Development Platform.
+ *
+ * Author: Nicolas Pitre
+ * Created: Nov 05, 2002
+ * Copyright: MontaVista Software Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation or any later version.
+ */
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/syscore_ops.h>
+#include <linux/interrupt.h>
+#include <linux/sched.h>
+#include <linux/bitops.h>
+#include <linux/fb.h>
+#include <linux/ioport.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/input.h>
+#include <linux/dm9000.h>
+#include <linux/slab.h>
+#include <linux/leds.h>
+#include <linux/ktime.h>
+#include <linux/irqchip/chained_irq.h>
+
+#include <asm/types.h>
+#include <asm/setup.h>
+#include <asm/memory.h>
+#include <asm/mach-types.h>
+#include <mach/hardware.h>
+#include <asm/irq.h>
+#include <asm/sizes.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+#include <asm/mach/flash.h>
+
+#include <mach/irqs.h>
+#include <mach/pxa27x.h>
+#include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/mmc-pxamci.h>
+#include <linux/platform_data/usb-ohci-pxa27x.h>
+#include <mach/smemc.h>
+
+#include "generic.h"
+#include "devices.h"
+
+#define LP8X4X_ETH0_BASE 0x0c000000
+#define LP8X4X_ETH0_IO 0x0c004000
+#define LP8X4X_ETH0_IRQ PXA_GPIO_TO_IRQ(9)
+
+#define LP8X4X_ETH1_BASE 0x0d000000
+#define LP8X4X_ETH1_IO 0x0d004000
+#define LP8X4X_ETH1_IRQ PXA_GPIO_TO_IRQ(82)
+
+#define LP8X4X_FPGA_PHYS 0x17000000
+#define LP8X4X_FPGA_VIRT ((void *) 0xf1000000)
+#define LP8X4X_P2V(x) IOMEM((x) - LP8X4X_FPGA_PHYS + LP8X4X_FPGA_VIRT)
+#define LP8X4X_V2P(x) ((x) - LP8X4X_FPGA_VIRT + LP8X4X_FPGA_PHYS)
+
+/* board level registers in the FPGA */
+
+#define LP8X4X_EOI LP8X4X_P2V(0x17009006)
+#define LP8X4X_INSINT LP8X4X_P2V(0x17009008)
+#define LP8X4X_ENSYSINT LP8X4X_P2V(0x1700900A)
+#define LP8X4X_PRIMINT LP8X4X_P2V(0x1700900C)
+#define LP8X4X_SECOINT LP8X4X_P2V(0x1700900E)
+#define LP8X4X_ENRISEINT LP8X4X_P2V(0x17009010)
+#define LP8X4X_CLRRISEINT LP8X4X_P2V(0x17009012)
+#define LP8X4X_ENHILVINT LP8X4X_P2V(0x17009014)
+#define LP8X4X_CLRHILVINT LP8X4X_P2V(0x17009016)
+#define LP8X4X_ENFALLINT LP8X4X_P2V(0x17009018)
+#define LP8X4X_CLRFALLINT LP8X4X_P2V(0x1700901a)
+
+/* board specific IRQs */
+
+#define LP8X4X_IRQ(x) (IRQ_BOARD_START + (x))
+#define LP8X4X_SLOT1_IRQ LP8X4X_IRQ(0)
+#define LP8X4X_SLOT2_IRQ LP8X4X_IRQ(1)
+#define LP8X4X_SLOT3_IRQ LP8X4X_IRQ(2)
+#define LP8X4X_SLOT4_IRQ LP8X4X_IRQ(3)
+#define LP8X4X_SLOT5_IRQ LP8X4X_IRQ(4)
+#define LP8X4X_SLOT6_IRQ LP8X4X_IRQ(5)
+#define LP8X4X_SLOT7_IRQ LP8X4X_IRQ(6)
+#define LP8X4X_SLOT8_IRQ LP8X4X_IRQ(7)
+#define LP8X4X_TIMER1_IRQ LP8X4X_IRQ(8)
+#define LP8X4X_TIMER2_IRQ LP8X4X_IRQ(9)
+#define LP8X4X_TIMEROUT_IRQ LP8X4X_IRQ(10)
+#define LP8X4X_HOTPLUG_IRQ LP8X4X_IRQ(11)
+#define LP8X4X_BATLOW_IRQ LP8X4X_IRQ(12)
+#define LP8X4X_TTYS0_IRQ LP8X4X_IRQ(13)
+#define LP8X4X_TTYS1_IRQ LP8X4X_IRQ(14)
+#define LP8X4X_TTYS2_IRQ LP8X4X_IRQ(15)
+
+#define LP8X4X_NR_IRQS (IRQ_BOARD_START + 16)
+
+static unsigned char lp8x4x_irq_sys_enabled;
+static unsigned char lp8x4x_irq_high_enabled;
+
+static void lp8x4x_ack_irq(struct irq_data *d)
+{
+ unsigned mask;
+ int irq = d->irq - IRQ_BOARD_START;
+
+ if (irq < 0 || irq > 15) {
+ pr_err("lp8x4x: wrong irq handler for irq %i\n", d->irq);
+ return;
+ }
+
+ if (irq < 8) {
+ mask = ioread8(LP8X4X_CLRHILVINT);
+ mask |= 1 << irq;
+ iowrite8(mask, LP8X4X_CLRHILVINT);
+ } else if (irq < 13) {
+ irq -= 8;
+ mask = ioread8(LP8X4X_SECOINT);
+ mask |= 1 << irq;
+ iowrite8(mask, LP8X4X_SECOINT);
+ } else {
+ irq -= 8;
+ mask = ioread8(LP8X4X_PRIMINT);
+ mask |= 1 << irq;
+ iowrite8(mask, LP8X4X_PRIMINT);
+ }
+}
+
+static void lp8x4x_mask_irq(struct irq_data *d)
+{
+ int irq = d->irq - IRQ_BOARD_START;
+
+ if (irq < 0 || irq > 15) {
+ pr_err("lp8x4x: wrong irq handler for irq %i\n", d->irq);
+ return;
+ }
+
+ if (irq < 8) {
+ lp8x4x_irq_high_enabled &= ~(1 << irq);
+ iowrite8(lp8x4x_irq_high_enabled, LP8X4X_ENHILVINT);
+ } else {
+ irq -= 8;
+ lp8x4x_irq_sys_enabled &= ~(1 << irq);
+ iowrite8(lp8x4x_irq_sys_enabled, LP8X4X_ENSYSINT);
+ }
+}
+
+static void lp8x4x_unmask_irq(struct irq_data *d)
+{
+ unsigned mask;
+ int irq = d->irq - IRQ_BOARD_START;
+
+ if (irq < 0 || irq > 15) {
+ pr_err("wrong irq handler for irq %i\n", d->irq);
+ return;
+ }
+
+ if (irq < 8) {
+ lp8x4x_irq_high_enabled |= 1 << irq;
+ mask = ioread8(LP8X4X_CLRHILVINT);
+ mask |= 1 << irq;
+ iowrite8(mask, LP8X4X_CLRHILVINT);
+ iowrite8(lp8x4x_irq_high_enabled, LP8X4X_ENHILVINT);
+ } else if (irq < 13) {
+ irq -= 8;
+ lp8x4x_irq_sys_enabled |= 1 << irq;
+ mask = ioread8(LP8X4X_SECOINT);
+ mask |= 1 << irq;
+ iowrite8(mask, LP8X4X_SECOINT);
+ iowrite8(lp8x4x_irq_sys_enabled, LP8X4X_ENSYSINT);
+ } else {
+ irq -= 8;
+ lp8x4x_irq_sys_enabled |= 1 << irq;
+ mask = ioread8(LP8X4X_PRIMINT);
+ mask |= 1 << irq;
+ iowrite8(mask, LP8X4X_PRIMINT);
+ iowrite8(lp8x4x_irq_sys_enabled, LP8X4X_ENSYSINT);
+ }
+}
+
+static struct irq_chip lp8x4x_irq_chip = {
+ .name = "FPGA",
+ .irq_ack = lp8x4x_ack_irq,
+ .irq_mask = lp8x4x_mask_irq,
+ .irq_unmask = lp8x4x_unmask_irq,
+};
+
+static spinlock_t fpga_irq_lock;
+
+static void lp8x4x_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+ int loop, n;
+ unsigned long mask;
+ unsigned long flags;
+ struct irq_chip *chip = irq_desc_get_chip(desc);
+
+ spin_lock_irqsave(&fpga_irq_lock, flags);
+ chained_irq_enter(chip, desc);
+
+ do {
+ loop = 0;
+ mask = ioread8(LP8X4X_CLRHILVINT) & 0xff;
+ mask |= (ioread8(LP8X4X_SECOINT) & 0x1f) << 8;
+ mask |= (ioread8(LP8X4X_PRIMINT) & 0xe0) << 8;
+ mask &= (lp8x4x_irq_high_enabled
+ | (lp8x4x_irq_sys_enabled << 8));
+ for_each_set_bit(n, &mask, BITS_PER_LONG) {
+ loop = 1;
+
+ generic_handle_irq(IRQ_BOARD_START + n);
+ }
+ } while (loop);
+
+ chained_irq_exit(chip, desc);
+ iowrite8(0, LP8X4X_EOI);
+ spin_unlock_irqrestore(&fpga_irq_lock, flags);
+}
+
+static void __init lp8x4x_init_irq(void)
+{
+ int irq;
+ int err;
+
+ err = irq_set_irq_type(PXA_GPIO_TO_IRQ(3), IRQ_TYPE_EDGE_RISING);
+ if (err < 0) {
+ pr_err("lp8x4x: irq init failed\n");
+ return;
+ }
+
+ spin_lock_init(&fpga_irq_lock);
+ irq_set_chained_handler(PXA_GPIO_TO_IRQ(3), lp8x4x_irq_handler);
+
+ for (irq = IRQ_BOARD_START; irq < LP8X4X_NR_IRQS; irq++) {
+ irq_set_chip_and_handler(irq, &lp8x4x_irq_chip,
+ handle_level_irq);
+ set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+ }
+
+ iowrite8(0, LP8X4X_CLRRISEINT);
+ iowrite8(0, LP8X4X_ENRISEINT);
+ iowrite8(0, LP8X4X_CLRFALLINT);
+ iowrite8(0, LP8X4X_ENFALLINT);
+ iowrite8(0, LP8X4X_CLRHILVINT);
+ iowrite8(0, LP8X4X_ENHILVINT);
+ iowrite8(0, LP8X4X_ENSYSINT);
+ iowrite8(0, LP8X4X_PRIMINT);
+ iowrite8(0, LP8X4X_SECOINT);
+
+ return;
+}
+
+static unsigned long lp8x4x_pin_config[] = {
+ /* MMC */
+ GPIO32_MMC_CLK,
+ GPIO112_MMC_CMD,
+ GPIO92_MMC_DAT_0,
+ GPIO109_MMC_DAT_1,
+ GPIO110_MMC_DAT_2,
+ GPIO111_MMC_DAT_3,
+
+ /* USB Host Port 1 */
+ GPIO88_USBH1_PWR,
+ GPIO89_USBH1_PEN,
+};
+
+static struct resource lp8x4x_flash_resources[] __initdata = {
+ [0] = {
+ .start = PXA_CS0_PHYS,
+ .end = PXA_CS0_PHYS + SZ_64M - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = PXA_CS1_PHYS,
+ .end = PXA_CS1_PHYS + SZ_32M - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct mtd_partition lp8x4x_flash0_partitions[] = {
+ {
+ .name = "Bootloader",
+ .size = 0x00040000,
+ .offset = 0,
+ }, {
+ .name = "Settings",
+ .size = 0x00040000,
+ .offset = 0x00040000,
+ }, {
+ .name = "Kernel",
+ .size = 0x00280000,
+ .offset = 0x00080000,
+ }, {
+ .name = "Filesystem",
+ .size = MTDPART_SIZ_FULL,
+ .offset = 0x00300000
+ }
+};
+
+static struct flash_platform_data lp8x4x_flash_data[] __initdata = {
+ {
+ .map_name = "cfi_probe",
+ .parts = lp8x4x_flash0_partitions,
+ .nr_parts = ARRAY_SIZE(lp8x4x_flash0_partitions),
+ .width = 4,
+ }, {
+ .map_name = "cfi_probe",
+ .parts = NULL,
+ .nr_parts = 0,
+ .width = 2,
+ }
+};
+
+static struct pxafb_mode_info lp8x4x_vga_60_mode = {
+ .pixclock = 38461,
+ .xres = 640,
+ .yres = 480,
+ .bpp = 16,
+ .hsync_len = 64,
+ .left_margin = 78,
+ .right_margin = 46,
+ .vsync_len = 12,
+ .upper_margin = 22,
+ .lower_margin = 10,
+ .sync = 0,
+};
+
+static struct pxafb_mach_info lp8x4x_pxafb_info = {
+ .num_modes = 1,
+ .lccr0 = LCCR0_Act,
+ .lccr3 = LCCR3_PCP,
+};
+
+static int lp8x4x_mci_init(struct device *dev,
+ irq_handler_t mstone_detect_int, void *data)
+{
+ return 0;
+}
+
+static int lp8x4x_mci_setpower(struct device *dev, unsigned int vdd)
+{
+ return 0;
+}
+
+static void lp8x4x_mci_exit(struct device *dev, void *data)
+{
+}
+
+static struct pxamci_platform_data lp8x4x_mci_platform_data = {
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .init = lp8x4x_mci_init,
+ .setpower = lp8x4x_mci_setpower,
+ .exit = lp8x4x_mci_exit,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
+};
+
+static struct resource lp8x4x_dm9000_resources[] __initdata = {
+ [0] = {
+ .start = LP8X4X_ETH0_BASE,
+ .end = LP8X4X_ETH0_BASE + 2 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = LP8X4X_ETH0_IO,
+ .end = LP8X4X_ETH0_IO + 2 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .start = LP8X4X_ETH0_IRQ,
+ .end = LP8X4X_ETH0_IRQ,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
+ },
+ [3] = {
+ .start = LP8X4X_ETH1_BASE,
+ .end = LP8X4X_ETH1_BASE + 2 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [4] = {
+ .start = LP8X4X_ETH1_IO,
+ .end = LP8X4X_ETH1_IO + 2 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [5] = {
+ .start = LP8X4X_ETH1_IRQ,
+ .end = LP8X4X_ETH1_IRQ,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
+ },
+};
+
+static struct pxaohci_platform_data lp8x4x_ohci_platform_data = {
+ .port_mode = PMM_PERPORT_MODE,
+ .flags = ENABLE_PORT1 | OC_MODE_PERPORT,
+};
+
+static void lp8x4x_restart(enum reboot_mode mode, const char *cmd)
+{
+ /* Switch off fast-bus and turbo mode */
+ asm volatile("mcr p14, 0, %0, c6, c0, 0" : :
+ "r"(2));
+ /* SDRAM hangs on watchdog reset on Marvell PXA270 (erratum 71) */
+ pxa_restart(REBOOT_SOFT, cmd);
+}
+
+static void __init lp8x4x_init(void)
+{
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(lp8x4x_pin_config));
+
+ pxa_set_ffuart_info(NULL);
+ pxa_set_btuart_info(NULL);
+ pxa_set_stuart_info(NULL);
+
+ /* system bus arbiter setting
+ * - Core_Park
+ * - LCD_wt:DMA_wt:CORE_Wt = 2:3:4
+ */
+ ARB_CNTRL = ARB_CORE_PARK | 0x234;
+
+ pxa_set_mci_info(&lp8x4x_mci_platform_data);
+ pxa_set_ohci_info(&lp8x4x_ohci_platform_data);
+
+ platform_device_register_resndata(NULL, "pxa2xx-flash", 0,
+ &lp8x4x_flash_resources[0], 1,
+ &lp8x4x_flash_data[0], sizeof(lp8x4x_flash_data[0]));
+ platform_device_register_resndata(NULL, "pxa2xx-flash", 1,
+ &lp8x4x_flash_resources[1], 1,
+ &lp8x4x_flash_data[1], sizeof(lp8x4x_flash_data[1]));
+ platform_device_register_simple("dm9000", 0,
+ &lp8x4x_dm9000_resources[0], 3);
+ platform_device_register_simple("dm9000", 1,
+ &lp8x4x_dm9000_resources[3], 3);
+
+ lp8x4x_pxafb_info.modes = &lp8x4x_vga_60_mode;
+ pxa_set_fb_info(NULL, &lp8x4x_pxafb_info);
+
+ /* Could not do this in MACHINE since GPIO is not ready then */
+ lp8x4x_init_irq();
+}
+
+static struct map_desc lp8x4x_io_desc[] __initdata = {
+ { /* CPLD */
+ .virtual = (unsigned long) LP8X4X_FPGA_VIRT,
+ .pfn = __phys_to_pfn(LP8X4X_FPGA_PHYS),
+ .length = 0x00100000,
+ .type = MT_DEVICE
+ }
+};
+
+static void __init lp8x4x_map_io(void)
+{
+ pxa27x_map_io();
+ iotable_init(lp8x4x_io_desc, ARRAY_SIZE(lp8x4x_io_desc));
+}
+
+MACHINE_START(LP8X4X, "ICP DAS LP-8x4x programmable automation controller")
+ .atag_offset = 0x100,
+ .map_io = lp8x4x_map_io,
+ .nr_irqs = LP8X4X_NR_IRQS,
+ .init_irq = pxa27x_init_irq,
+ .handle_irq = pxa27x_handle_irq,
+ .init_time = pxa_timer_init,
+ .init_machine = lp8x4x_init,
+ .restart = lp8x4x_restart,
+MACHINE_END
--
1.8.4.2
More information about the linux-arm-kernel
mailing list