[PATCH v6 3/3] mfd: max14577: Add device tree bindings document

[Chanwoo Choi]

Hi Krzysztof,

On 12/04/2013 07:40 PM, Krzysztof Kozlowski wrote:
> Add document describing device tree bindings for MAX14577 MFD driver.
> 
> Signed-off-by: Krzysztof Kozlowski <k.kozlowski at samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park at samsung.com>
> ---
>  Documentation/devicetree/bindings/mfd/max14577.txt |   48 ++++++++++++++++++++
>  1 file changed, 48 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/max14577.txt
> 
> diff --git a/Documentation/devicetree/bindings/mfd/max14577.txt b/Documentation/devicetree/bindings/mfd/max14577.txt
> new file mode 100644
> index 000000000000..f4fd16360b6b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/max14577.txt
> @@ -0,0 +1,48 @@
> +MAXIM MAX14577 multi-function device
> +
> +MAX14577 is a Multi-function device with Micro-USB Interface Circuit, Li+
> +Battery Charger and SFOUT LDO output for powering USB devices. It is
> +interfaced to host controller using I2C.
> +
> +Required properties:
> +- compatible : Must be "maxim,max14577".
> +- reg : I2C slave address for the max14577 chip.
> +- interrupts : IRQ line for the max14577 chip.
> +- interrupt-parent :  The parent interrupt controller.
> +
> +Optional nodes:
> +- regulators :
> +  Required child node properties:
> +  - compatible : "maxim,max14577-regulator"
> +
> +  Optional child nodes:
> +    Each child node representing a regulator, following standard regulator
> +    bindings. Valid names for a regulator are: "CHARGER" and "SAFEOUT".
> +    The SAFEOUT is a constant voltage regulator so there is no need to specify
> +    voltages for it.
> +
> +	[*] refer Documentation/devicetree/bindings/regulator/regulator.txt
> +
> +Example:
> +	max14577 at 25 {
> +		compatible = "maxim,max14577";
> +		reg = <0x25>;
> +		interrupt-parent = <&gpx1>;
> +		interrupts = <5 0>;
> +
> +		regulators {
> +			compatible = "maxim,max14577-regulator";
> +
> +			safeout_reg: safeout at 1 {
> +				regulator-compatible = "SAFEOUT";
> +				regulator-name = "SAFEOUT";
> +			};
> +			charger_reg: charger at 0 {
> +				regulator-compatible = "CHARGER";
> +				regulator-name = "CHARGER";
> +				regulator-min-microamp = <90000>;
> +				regulator-max-microamp = <950000>;
> +				regulator-boot-on;
> +			};
> +		};

I prefer to add dt data about max14577-muic on following:
If extcon consumer driver need to use muic device, dts should provide following dt data.

		muic: max14577-muic {
			compatible = "maxim, max14577-muic";
		};
> +	};
> 

For example,
If fuel-gauge want to use extcon subsystem, dt data of fuel-gauge add 'extcon' property as following:

	fuel-gague@ {
		compatible = "...";
		extcon = <&muic>;
	}


Thanks,
Chanwoo Choi