Spurious timeouts in mvmdio

Jason Cooper jason at lakedaemon.net
Tue Dec 3 08:43:10 EST 2013


On Tue, Dec 03, 2013 at 12:40:34PM +0000, Russell King - ARM Linux wrote:
> On Tue, Dec 03, 2013 at 07:23:46AM -0500, Jason Cooper wrote:
> > On Mon, Dec 02, 2013 at 04:15:54PM +0100, Nicolas Schichan wrote:
> > > During 3.13-rc1 testing, I have found out that the mvmdio driver
> > > would report timeouts on the kernel console:
> > > 
> > > [   11.011334] orion-mdio orion-mdio: Timeout: SMI busy for too long
> > > 
> > > The hardware is a MV88F6281 Kirkwood CPU. The mvmdio driver is using
> > > the irq line 46 (ge00_err).
> > > 
> > > I am inclined to believe that it is due to the fact that
> > > wait_event_timeout() is called with a timeout parameter of 1 jiffy
> > > in orion_mdio_wait_ready(). If the timer interrupt ticks right after
> > > calling wait_event_timeout(), we may end up spending much less time
> > > than MVMDIO_SMI_TIMEOUT (1 msec) in wait_event_timeout(), and as a
> > > result report a timeout as the MDIO access did not complete in such
> > > a short time.
> > > 
> > > As to how to fix this, I see two options (I don't know which one
> > > would be prefered):
> > > 
> > > - Option 1: always pass a timeout of at least 2 jiffy to wait_event_timeout().
> > > - Option 2: switch to wait_event_hrtimeout().
> > > 
> > > I can provide patches for both options.
> > 
> > Based on yesterday's irc chat, option 1 sounds good.  Here's the dump
> > from yesterday where Sebastian provided a thorough explanation:
> > 
> > 11:29 < shesselba> increasing max timeout to 2 ticks at least sounds reasonable
> > 11:29 < shesselba> 10ms should be enough for every CONFIG_HZ there is
> > 
> > 11:30 < kos_tom> why make the timeout tied to the ticks? there are functions/macros to convert real time numbers into ticks.
> > 11:30 < kos_tom> msecs_to_jiffies() or something
> > 
> > 11:31 < shesselba> kos_tom: it is already using usecs_to_jiffies()
> > 11:31 < shesselba> the thing is: 1ms is less than a jiffy
> 
> Yes, and the kernels time conversion functions aren't stupid.  Let's
> look at this function's implementation:
> 
> unsigned long usecs_to_jiffies(const unsigned int u)
> {
>         if (u > jiffies_to_usecs(MAX_JIFFY_OFFSET))
>                 return MAX_JIFFY_OFFSET;
> #if HZ <= USEC_PER_SEC && !(USEC_PER_SEC % HZ)
>         return (u + (USEC_PER_SEC / HZ) - 1) / (USEC_PER_SEC / HZ);
> #elif HZ > USEC_PER_SEC && !(HZ % USEC_PER_SEC)
>         return u * (HZ / USEC_PER_SEC);
> #else
>         return (USEC_TO_HZ_MUL32 * u + USEC_TO_HZ_ADJ32)
>                 >> USEC_TO_HZ_SHR32;
> #endif
> }
> 
> Now, assuming HZ=100 and USEC_PER_SEC=1000000, we will use:
> 
> 	return (u + (USEC_PER_SEC / HZ) - 1) / (USEC_PER_SEC / HZ);
> 
> If you ask for 1us, this comes out as:
> 
> 	return (1 + (1000000 / 100) - 1) / (1000000 / 100);
> 
> which is one jiffy.  So, for a requested 1us period, you're given a
> 1 jiffy interval, or 10ms.  For other (sensible) values:
> 
>         return (USEC_TO_HZ_MUL32 * u + USEC_TO_HZ_ADJ32)
>                 >> USEC_TO_HZ_SHR32;
> 
> gets used, which has a similar behaviour.
> 
> Now, depending on how you use this one jiffy interval, the thing to realise
> is that with this kind of loop:
> 
> 	timeout = jiffies + usecs_to_jiffies(1);
> 	do {
> 		something;
> 	} while (time_is_before_jiffies(timeout));
> 
> what this equates to is:
> 
> 	} while (jiffies - timeout < 0);
> 
> What this means is that the loop breaks at jiffies = timeout, so it can
> indeed timeout before one tick - within 0 to 10ms for HZ=100.  The problem
> is not the usecs_to_jiffies(), it's with the implementation.

Ack.

> If you use time_is_before_eq_jiffies() instead, it will also loop if
> jiffies == timeout, which will give you the additional safety margin -
> meaning it will timeout after 10 to 20ms instead.
> 
> You may wish to consider coding this differently as well - if you have
> the error interrupt, there's no need for this loop.  You only need the
> loop if you're using usleep_range().  Note the return value of
> wait_event_timeout() will tell you positively and correctly if the waited
> condition succeeded or you timed out.

Nicolas, sorry for the confusion.  Mind spinning a v2?

thx,

Jason.



More information about the linux-arm-kernel mailing list