[PATCH V5 0/4] DRIVERS: IRQCHIP: Add support for crossbar IP

[Sricharan R]

Some socs have a large number of interrupts requests to service
the needs of its many peripherals and subsystems. All of the interrupt
requests lines from the subsystems are not needed at the same
time, so they have to be muxed to the controllers appropriately.
In such places a interrupt controllers are preceded by an
IRQ CROSSBAR that provides flexibility in muxing the device interrupt
requests to the controller inputs.

This series models the peripheral interrupts that can be routed through
the crossbar to the GIC as 'routable-irqs'. The routable irqs are added
in a separate linear domain inside the GIC. The registered routable domain's
callback are invoked as a part of the GIC's callback, which in turn should
allocate a free irq line and configure the IP accordingly. So every peripheral
in the dts files mentions the fixed crossbar number as its interrupt. A free
gic line for that gets allocated and configured when the peripheral interrupts
are mapped.

The minimal crossbar driver to track and allocate free GIC lines and configure the
crossbar is added here, along with the DT bindings.

V5:
   Addressed a comment from Mark Rutland <mark.rutland at arm.com>,
   updated tags and rebased on 3.13-rc2

V4:
   Addressed a couple of comments and split the DTS file updates in to
   a separate series.

V3:
   Addressed few more comments from Thomas Gleixner <tglx at linutronix.de>

   Rebased patches 3,4,5,7 which updates the DTS file on top of below branch
	   git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt.git
	   for_3.13/dts

   Rebased patches 1,2,6 on top of 3.12 mainline
   Updated Commit tags

V2:
   Addressed Thomas Gleixner <tglx at linutronix.de> comments and
   Kumar Gala <galak at codeaurora.org>

   Split updating the DRA7.dtsi file for adding the routable-irqs

Previous discussions that led to this is at
	https://lkml.org/lkml/2013/9/18/540

The V1,V2,V3,V4 post of these patches is at
      [V1]  https://lkml.org/lkml/2013/9/30/283
      [V2]  http://www.spinics.net/lists/linux-omap/msg99540.html
      [V3]  http://www.kernelhub.org/?msg=356470&p=2
      [V4]  http://www.spinics.net/lists/linux-doc/msg16726.html

Sricharan R (4):
  DRIVERS: IRQCHIP: IRQ-GIC: Add support for routable irqs
  DRIVERS: IRQCHIP: CROSSBAR: Add support for Crossbar IP
  ARM: OMAP4+: Correct Wakeup-gen code to use physical irq number
  ARM: DRA: Enable Crossbar IP support for DRA7XX

 Documentation/devicetree/bindings/arm/gic.txt      |    6 +
 .../devicetree/bindings/arm/omap/crossbar.txt      |   27 +++
 arch/arm/mach-omap2/Kconfig                        |    1 +
 arch/arm/mach-omap2/omap-wakeupgen.c               |    4 +-
 arch/arm/mach-omap2/omap4-common.c                 |    2 +
 drivers/irqchip/Kconfig                            |    8 +
 drivers/irqchip/Makefile                           |    1 +
 drivers/irqchip/irq-crossbar.c                     |  208 ++++++++++++++++++++
 drivers/irqchip/irq-gic.c                          |   81 +++++++-
 include/linux/irqchip/arm-gic.h                    |    7 +-
 include/linux/irqchip/irq-crossbar.h               |   11 ++
 11 files changed, 343 insertions(+), 13 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/arm/omap/crossbar.txt
 create mode 100644 drivers/irqchip/irq-crossbar.c
 create mode 100644 include/linux/irqchip/irq-crossbar.h

-- 
1.7.9.5