[PATCH 2/3] clk: ux500: Support prcmu ape opp voltage clock

[Ulf Hansson]

Hi Mike,

On 26 September 2012 21:25, Mike Turquette <mturquette at ti.com> wrote:
> Quoting Ulf Hansson (2012-09-25 00:56:56)
>> Hi Mike,
>>
>> Thanks for your input!
>>
>> On 24 September 2012 17:35, Mike Turquette <mturquette at ti.com> wrote:
>> > Quoting Ulf Hansson (2012-09-24 07:43:18)
>> >> From: Ulf Hansson <ulf.hansson at linaro.org>
>> >>
>> >> Some scalable prcmu clocks needs to be handled in conjuction with the
>> >> ape opp 100 voltage. A new prcmu clock type clk_prcmu_opp_volt_scalable
>> >> is implemented to handle this.
>> >>
>> >> Signed-off-by: Ulf Hansson <ulf.hansson at linaro.org>
>> >> ---
>> >>  drivers/clk/ux500/clk-prcmu.c |   55 +++++++++++++++++++++++++++++++++++++++++
>> >>  drivers/clk/ux500/clk.h       |    6 +++++
>> >>  2 files changed, 61 insertions(+)
>> >>
>> >> diff --git a/drivers/clk/ux500/clk-prcmu.c b/drivers/clk/ux500/clk-prcmu.c
>> >> index 930cdfe..04577ca 100644
>> >> --- a/drivers/clk/ux500/clk-prcmu.c
>> >> +++ b/drivers/clk/ux500/clk-prcmu.c
>> >> @@ -133,6 +133,40 @@ out_error:
>> >>                 hw->init->name);
>> >>  }
>> >>
>> >> +static int clk_prcmu_opp_volt_prepare(struct clk_hw *hw)
>> >> +{
>> >> +       int err;
>> >> +       struct clk_prcmu *clk = to_clk_prcmu(hw);
>> >> +
>> >> +       err = prcmu_request_ape_opp_100_voltage(true);
>> >> +       if (err) {
>> >> +               pr_err("clk_prcmu: %s failed to request APE OPP VOLT for %s.\n",
>> >> +                       __func__, hw->init->name);
>> >> +               return err;
>> >> +       }
>> >> +
>> >> +       err = prcmu_request_clock(clk->cg_sel, true);
>> >> +       if (err)
>> >> +               prcmu_request_ape_opp_100_voltage(false);
>> >> +
>> >> +       return err;
>> >> +}
>> >> +
>> >> +static void clk_prcmu_opp_volt_unprepare(struct clk_hw *hw)
>> >> +{
>> >> +       struct clk_prcmu *clk = to_clk_prcmu(hw);
>> >> +
>> >> +       if (prcmu_request_clock(clk->cg_sel, false))
>> >> +               goto out_error;
>> >> +       if (prcmu_request_ape_opp_100_voltage(false))
>> >> +               goto out_error;
>> >> +       return;
>> >> +
>> >> +out_error:
>> >> +       pr_err("clk_prcmu: %s failed to disable %s.\n", __func__,
>> >> +               hw->init->name);
>> >> +}
>> >
>> > Hello Ulf,
>> >
>> > I was hoping to use the rate-change notifiers for voltage scaling, as in
>> > my clk reentrancy/dvfs RFCs.  Using prepare/unprepare to set voltage for
>> > non-scalable clocks is probably OK; do you plan to scale voltage when
>> > your clocks change rate?  If so then you will need more than just
>> > prepare/unprepare.
>>
>> I see, you have a good point here. Although right now this clock will
>> never change rate except during "init". Prepare/unprepare is thus
>> enough.
>>
>> For the u8500 platform the sdmmc clock is the parent for all the
>> mmc/sd/sdio controllers. So, to no introduce a very complex
>> clockhandling mechanism (using rate-change notifiers would help a bit,
>> but is not enough), the clock is not supposed to be changed after
>> init. Proper dividing of the clock is handled internally by each
>> controller instead.
>>
>
> The internal dividers could be modeled as clk nodes, which themselves
> could have notifier handlers that scale voltage.  So perhaps the MMC
> controller driver for your platform should define the appropriate leaf
> clks?

I am not sure I completely follow you here, but let me try to answer
your suggestions.
The internal dividers are supposed to be handled only by the mmc host
driver since it is IP specific. I don't think it is viable to add
another clock type/node for this, but maybe that is not what you are
suggesting either. :-)

In my case for ux500 we use the mmci host driver. It is an ARM cross
SoC device driver, and I believe adding clock notifiers in the driver
to handle the voltage scale would complicate things quite a bit. It
seems a lot easier to let the clock driver handle this, especially
since the frequency will remain fixed after initialization. So in the
end I see now need and benefit for adding the clock notifiers in the
mmci host driver.

Kind regards
Ulf Hansson