[PATCH v3 13/17] ARM: LPAE: factor out T1SZ and TTBR1 computations

[Cyril Chemparathy]

This patch moves the TTBR1 offset calculation and the T1SZ calculation out
of the TTB setup assembly code.  This should not affect functionality in
any way, but improves code readability as well as readability of subsequent
patches in this series.

Signed-off-by: Cyril Chemparathy <cyril at ti.com>
Signed-off-by: Vitaly Andrianov <vitalya at ti.com>
Acked-by: Nicolas Pitre <nico at linaro.org>
---
 arch/arm/include/asm/pgtable-3level-hwdef.h |   10 ++++++++++
 arch/arm/mm/proc-v7-3level.S                |   16 ++++------------
 2 files changed, 14 insertions(+), 12 deletions(-)

diff --git a/arch/arm/include/asm/pgtable-3level-hwdef.h b/arch/arm/include/asm/pgtable-3level-hwdef.h
index d795282..b501650 100644
--- a/arch/arm/include/asm/pgtable-3level-hwdef.h
+++ b/arch/arm/include/asm/pgtable-3level-hwdef.h
@@ -74,4 +74,14 @@
 #define PHYS_MASK_SHIFT		(40)
 #define PHYS_MASK		((1ULL << PHYS_MASK_SHIFT) - 1)
 
+#if defined CONFIG_VMSPLIT_2G
+#define TTBR1_OFFSET	(1 << 4)		/* skip two L1 entries */
+#elif defined CONFIG_VMSPLIT_3G
+#define TTBR1_OFFSET	(4096 * (1 + 3))	/* only L2, skip pgd + 3*pmd */
+#else
+#define TTBR1_OFFSET	0
+#endif
+
+#define TTBR1_SIZE	(((PAGE_OFFSET >> 30) - 1) << 16)
+
 #endif
diff --git a/arch/arm/mm/proc-v7-3level.S b/arch/arm/mm/proc-v7-3level.S
index c4f4251..5d93f00 100644
--- a/arch/arm/mm/proc-v7-3level.S
+++ b/arch/arm/mm/proc-v7-3level.S
@@ -128,18 +128,10 @@ ENDPROC(cpu_v7_set_pte_ext)
 	 * booting secondary CPUs would end up using TTBR1 for the identity
 	 * mapping set up in TTBR0.
 	 */
-	bhi	9001f				@ PHYS_OFFSET > PAGE_OFFSET?
-	orr	\tmp, \tmp, #(((PAGE_OFFSET >> 30) - 1) << 16) @ TTBCR.T1SZ
-#if defined CONFIG_VMSPLIT_2G
-	/* PAGE_OFFSET == 0x80000000, T1SZ == 1 */
-	add	\ttbr1, \ttbr1, #1 << 4		@ skip two L1 entries
-#elif defined CONFIG_VMSPLIT_3G
-	/* PAGE_OFFSET == 0xc0000000, T1SZ == 2 */
-	add	\ttbr1, \ttbr1, #4096 * (1 + 3)	@ only L2 used, skip pgd+3*pmd
-#endif
-	/* CONFIG_VMSPLIT_1G does not need TTBR1 adjustment */
-9001:	mcr	p15, 0, \tmp, c2, c0, 2		@ TTB control register
-	mcrr	p15, 1, \ttbr1, \zero, c2	@ load TTBR1
+	orrls	\tmp, \tmp, #TTBR1_SIZE				@ TTBCR.T1SZ
+	mcr	p15, 0, \tmp, c2, c0, 2				@ TTBCR
+	addls	\ttbr1, \ttbr1, #TTBR1_OFFSET
+	mcrr	p15, 1, \ttbr1, \zero, c2			@ load TTBR1
 	.endm
 
 	__CPUINIT
-- 
1.7.9.5