[PATCH 01/17] ASoC: Ux500: Move MSP pinctrl setup into the MSP driver
Ola Lilja
ola.o.lilja at stericsson.com
Tue Sep 11 05:28:16 EDT 2012
On 09/10/2012 06:46 PM, Lee Jones wrote:
> Ola poke.
>
> On Fri, Aug 24, 2012 at 03:01:37PM +0100, Lee Jones wrote:
>> In the initial submission of the MSP driver msp1 and msp3's associated
>> pinctrl mechanism was passed back to platform code using a plat_init()
>> call-back routine, but it has no place in platform code. The MSP driver
>> should set this up for the appropriate ports. Instead we use a use_pinctrl
>> identifier which is passed from platform_data/Device Tree which indicates
>> which ports should use pinctrl.
>>
>> CC: alsa-devel at alsa-project.org
>> Signed-off-by: Lee Jones <lee.jones at linaro.org>
>> ---
>> arch/arm/mach-ux500/board-mop500-msp.c | 75 +-------------------------------
>> arch/arm/mach-ux500/include/mach/msp.h | 2 -
>> sound/soc/ux500/ux500_msp_i2s.c | 67 +++++++++++++++++++++-------
>> sound/soc/ux500/ux500_msp_i2s.h | 8 +++-
>> 4 files changed, 58 insertions(+), 94 deletions(-)
>>
>> diff --git a/arch/arm/mach-ux500/board-mop500-msp.c b/arch/arm/mach-ux500/board-mop500-msp.c
>> index df15646..fc78d5d 100644
>> --- a/arch/arm/mach-ux500/board-mop500-msp.c
>> +++ b/arch/arm/mach-ux500/board-mop500-msp.c
>> @@ -23,53 +23,6 @@
>> #include "devices-db8500.h"
>> #include "pins-db8500.h"
>>
>> -/* MSP1/3 Tx/Rx usage protection */
>> -static DEFINE_SPINLOCK(msp_rxtx_lock);
>> -
>> -/* Reference Count */
>> -static int msp_rxtx_ref;
>> -
>> -/* Pin modes */
>> -struct pinctrl *msp1_p;
>> -struct pinctrl_state *msp1_def;
>> -struct pinctrl_state *msp1_sleep;
>> -
>> -int msp13_i2s_init(void)
>> -{
>> - int retval = 0;
>> - unsigned long flags;
>> -
>> - spin_lock_irqsave(&msp_rxtx_lock, flags);
>> - if (msp_rxtx_ref == 0 && !(IS_ERR(msp1_p) || IS_ERR(msp1_def))) {
>> - retval = pinctrl_select_state(msp1_p, msp1_def);
>> - if (retval)
>> - pr_err("could not set MSP1 defstate\n");
>> - }
>> - if (!retval)
>> - msp_rxtx_ref++;
>> - spin_unlock_irqrestore(&msp_rxtx_lock, flags);
>> -
>> - return retval;
>> -}
>> -
>> -int msp13_i2s_exit(void)
>> -{
>> - int retval = 0;
>> - unsigned long flags;
>> -
>> - spin_lock_irqsave(&msp_rxtx_lock, flags);
>> - WARN_ON(!msp_rxtx_ref);
>> - msp_rxtx_ref--;
>> - if (msp_rxtx_ref == 0 && !(IS_ERR(msp1_p) || IS_ERR(msp1_sleep))) {
>> - retval = pinctrl_select_state(msp1_p, msp1_sleep);
>> - if (retval)
>> - pr_err("could not set MSP1 sleepstate\n");
>> - }
>> - spin_unlock_irqrestore(&msp_rxtx_lock, flags);
>> -
>> - return retval;
>> -}
>> -
>> static struct stedma40_chan_cfg msp0_dma_rx = {
>> .high_priority = true,
>> .dir = STEDMA40_PERIPH_TO_MEM,
>> @@ -132,8 +85,6 @@ static struct msp_i2s_platform_data msp1_platform_data = {
>> .id = MSP_I2S_1,
>> .msp_i2s_dma_rx = NULL,
>> .msp_i2s_dma_tx = &msp1_dma_tx,
>> - .msp_i2s_init = msp13_i2s_init,
>> - .msp_i2s_exit = msp13_i2s_exit,
>> };
>>
>> static struct stedma40_chan_cfg msp2_dma_rx = {
>> @@ -219,47 +170,23 @@ static struct msp_i2s_platform_data msp3_platform_data = {
>> .id = MSP_I2S_3,
>> .msp_i2s_dma_rx = &msp1_dma_rx,
>> .msp_i2s_dma_tx = NULL,
>> - .msp_i2s_init = msp13_i2s_init,
>> - .msp_i2s_exit = msp13_i2s_exit,
>> };
>>
>> int mop500_msp_init(struct device *parent)
>> {
>> - struct platform_device *msp1;
>> -
>> pr_info("%s: Register platform-device 'snd-soc-mop500'.\n", __func__);
>> platform_device_register(&snd_soc_mop500);
>>
>> pr_info("Initialize MSP I2S-devices.\n");
>> db8500_add_msp_i2s(parent, 0, U8500_MSP0_BASE, IRQ_DB8500_MSP0,
>> &msp0_platform_data);
>> - msp1 = db8500_add_msp_i2s(parent, 1, U8500_MSP1_BASE, IRQ_DB8500_MSP1,
>> + db8500_add_msp_i2s(parent, 1, U8500_MSP1_BASE, IRQ_DB8500_MSP1,
>> &msp1_platform_data);
>> db8500_add_msp_i2s(parent, 2, U8500_MSP2_BASE, IRQ_DB8500_MSP2,
>> &msp2_platform_data);
>> db8500_add_msp_i2s(parent, 3, U8500_MSP3_BASE, IRQ_DB8500_MSP1,
>> &msp3_platform_data);
>>
>> - /* Get the pinctrl handle for MSP1 */
>> - if (msp1) {
>> - msp1_p = pinctrl_get(&msp1->dev);
>> - if (IS_ERR(msp1_p))
>> - dev_err(&msp1->dev, "could not get MSP1 pinctrl\n");
>> - else {
>> - msp1_def = pinctrl_lookup_state(msp1_p,
>> - PINCTRL_STATE_DEFAULT);
>> - if (IS_ERR(msp1_def)) {
>> - dev_err(&msp1->dev,
>> - "could not get MSP1 defstate\n");
>> - }
>> - msp1_sleep = pinctrl_lookup_state(msp1_p,
>> - PINCTRL_STATE_SLEEP);
>> - if (IS_ERR(msp1_sleep))
>> - dev_err(&msp1->dev,
>> - "could not get MSP1 idlestate\n");
>> - }
>> - }
>> -
>> pr_info("%s: Register platform-device 'ux500-pcm'\n", __func__);
>> platform_device_register(&ux500_pcm);
>>
>> diff --git a/arch/arm/mach-ux500/include/mach/msp.h b/arch/arm/mach-ux500/include/mach/msp.h
>> index 798be19..3cc7142 100644
>> --- a/arch/arm/mach-ux500/include/mach/msp.h
>> +++ b/arch/arm/mach-ux500/include/mach/msp.h
>> @@ -22,8 +22,6 @@ struct msp_i2s_platform_data {
>> enum msp_i2s_id id;
>> struct stedma40_chan_cfg *msp_i2s_dma_rx;
>> struct stedma40_chan_cfg *msp_i2s_dma_tx;
>> - int (*msp_i2s_init) (void);
>> - int (*msp_i2s_exit) (void);
>> };
>>
>> #endif
>> diff --git a/sound/soc/ux500/ux500_msp_i2s.c b/sound/soc/ux500/ux500_msp_i2s.c
>> index 36be11e..08813c5 100644
>> --- a/sound/soc/ux500/ux500_msp_i2s.c
>> +++ b/sound/soc/ux500/ux500_msp_i2s.c
>> @@ -15,6 +15,7 @@
>>
>> #include <linux/module.h>
>> #include <linux/platform_device.h>
>> +#include <linux/pinctrl/consumer.h>
>> #include <linux/delay.h>
>> #include <linux/slab.h>
>>
>> @@ -25,6 +26,9 @@
>>
>> #include "ux500_msp_i2s.h"
>>
>> +/* MSP1/3 Tx/Rx usage protection */
>> +static DEFINE_SPINLOCK(msp_rxtx_lock);
>> +
>> /* Protocol desciptors */
>> static const struct msp_protdesc prot_descs[] = {
>> { /* I2S */
>> @@ -352,17 +356,23 @@ static int configure_multichannel(struct ux500_msp *msp,
>>
>> static int enable_msp(struct ux500_msp *msp, struct ux500_msp_config *config)
>> {
>> - int status = 0;
>> + int status = 0, retval = 0;
>> u32 reg_val_DMACR, reg_val_GCR;
>> + unsigned long flags;
>>
>> /* Check msp state whether in RUN or CONFIGURED Mode */
>> - if ((msp->msp_state == MSP_STATE_IDLE) && (msp->plat_init)) {
>> - status = msp->plat_init();
>> - if (status) {
>> - dev_err(msp->dev, "%s: ERROR: Failed to init MSP (%d)!\n",
>> - __func__, status);
>> - return status;
>> + if (msp->msp_state == MSP_STATE_IDLE) {
>> + spin_lock_irqsave(&msp_rxtx_lock, flags);
>> + if (msp->pinctrl_rxtx_ref == 0 &&
>> + !(IS_ERR(msp->pinctrl_p) || IS_ERR(msp->pinctrl_def))) {
>> + retval = pinctrl_select_state(msp->pinctrl_p,
>> + msp->pinctrl_def);
>> + if (retval)
>> + pr_err("could not set MSP defstate\n");
>> }
>> + if (!retval)
>> + msp->pinctrl_rxtx_ref++;
>> + spin_unlock_irqrestore(&msp_rxtx_lock, flags);
>> }
>>
>> /* Configure msp with protocol dependent settings */
>> @@ -620,7 +630,8 @@ int ux500_msp_i2s_trigger(struct ux500_msp *msp, int cmd, int direction)
>>
>> int ux500_msp_i2s_close(struct ux500_msp *msp, unsigned int dir)
>> {
>> - int status = 0;
>> + int status = 0, retval = 0;
>> + unsigned long flags;
>>
>> dev_dbg(msp->dev, "%s: Enter (dir = 0x%01x).\n", __func__, dir);
>>
>> @@ -631,12 +642,19 @@ int ux500_msp_i2s_close(struct ux500_msp *msp, unsigned int dir)
>> writel((readl(msp->registers + MSP_GCR) &
>> (~(FRAME_GEN_ENABLE | SRG_ENABLE))),
>> msp->registers + MSP_GCR);
>> - if (msp->plat_exit)
>> - status = msp->plat_exit();
>> - if (status)
>> - dev_warn(msp->dev,
>> - "%s: WARN: ux500_msp_i2s_exit failed (%d)!\n",
>> - __func__, status);
>> +
>> + spin_lock_irqsave(&msp_rxtx_lock, flags);
>> + WARN_ON(!msp->pinctrl_rxtx_ref);
>> + msp->pinctrl_rxtx_ref--;
>> + if (msp->pinctrl_rxtx_ref == 0 &&
>> + !(IS_ERR(msp->pinctrl_p) || IS_ERR(msp->pinctrl_sleep))) {
>> + retval = pinctrl_select_state(msp->pinctrl_p,
>> + msp->pinctrl_sleep);
>> + if (retval)
>> + pr_err("could not set MSP sleepstate\n");
>> + }
>> + spin_unlock_irqrestore(&msp_rxtx_lock, flags);
>> +
>> writel(0, msp->registers + MSP_GCR);
>> writel(0, msp->registers + MSP_TCF);
>> writel(0, msp->registers + MSP_RCF);
>> @@ -678,8 +696,6 @@ int ux500_msp_i2s_init_msp(struct platform_device *pdev,
>>
>> msp->id = platform_data->id;
>> msp->dev = &pdev->dev;
>> - msp->plat_init = platform_data->msp_i2s_init;
>> - msp->plat_exit = platform_data->msp_i2s_exit;
>> msp->dma_cfg_rx = platform_data->msp_i2s_dma_rx;
>> msp->dma_cfg_tx = platform_data->msp_i2s_dma_tx;
>>
>> @@ -717,6 +733,25 @@ int ux500_msp_i2s_init_msp(struct platform_device *pdev,
>> dev_dbg(&pdev->dev, "I2S device-name: '%s'\n", i2s_cont->name);
>> msp->i2s_cont = i2s_cont;
>>
>> + msp->pinctrl_p = pinctrl_get(msp->dev);
>> + if (IS_ERR(msp->pinctrl_p))
>> + dev_err(&pdev->dev, "could not get MSP pinctrl\n");
>> + else {
>> + msp->pinctrl_def = pinctrl_lookup_state(msp->pinctrl_p,
>> + PINCTRL_STATE_DEFAULT);
>> + if (IS_ERR(msp->pinctrl_def)) {
>> + dev_err(&pdev->dev,
>> + "could not get MSP defstate (%li)\n",
>> + PTR_ERR(msp->pinctrl_def));
>> + }
>> + msp->pinctrl_sleep = pinctrl_lookup_state(msp->pinctrl_p,
>> + PINCTRL_STATE_SLEEP);
>> + if (IS_ERR(msp->pinctrl_sleep))
>> + dev_err(&pdev->dev,
>> + "could not get MSP idlestate (%li)\n",
>> + PTR_ERR(msp->pinctrl_def));
>> + }
>> +
>> return 0;
>>
>> err_i2s_cont:
>> diff --git a/sound/soc/ux500/ux500_msp_i2s.h b/sound/soc/ux500/ux500_msp_i2s.h
>> index 2d9136d..1311c0d 100644
>> --- a/sound/soc/ux500/ux500_msp_i2s.h
>> +++ b/sound/soc/ux500/ux500_msp_i2s.h
>> @@ -524,14 +524,18 @@ struct ux500_msp {
>> struct dma_chan *rx_pipeid;
>> enum msp_state msp_state;
>> int (*transfer) (struct ux500_msp *msp, struct i2s_message *message);
>> - int (*plat_init) (void);
>> - int (*plat_exit) (void);
>> struct timer_list notify_timer;
>> int def_elem_len;
>> unsigned int dir_busy;
>> int loopback_enable;
>> u32 backup_regs[MAX_MSP_BACKUP_REGS];
>> unsigned int f_bitclk;
>> + /* Pin modes */
>> + struct pinctrl *pinctrl_p;
>> + struct pinctrl_state *pinctrl_def;
>> + struct pinctrl_state *pinctrl_sleep;
>> + /* Reference Count */
>> + int pinctrl_rxtx_ref;
>> };
>>
>> struct ux500_msp_dma_params {
>> --
>> 1.7.9.5
>>
>
Looks OK from my perspective!
More information about the linux-arm-kernel
mailing list