[PATCH 2/5] drivers: usb: otg: make twl6030_usb as a comparator driver to omap_usb2

[Tony Lindgren]

* Benoit Cousson <b-cousson at ti.com> [121026 08:23]:
> Hi Roger,
> 
> On 10/26/2012 05:16 PM, Roger Quadros wrote:
> > Hi Kishon & Benoit,
> > 
> > On 09/24/2012 12:06 PM, Rabin Vincent wrote:
> >> 2012/9/24 ABRAHAM, KISHON VIJAY <kishon at ti.com>:
> >>> On Sat, Sep 22, 2012 at 3:03 AM, Rabin Vincent <rabin at rab.in> wrote:
> >>>> USB doesn't work on pandaboard on linux-next, and bisection shows this
> >>>> patch.  Unfortunately, I can't provide a dmesg log because USB is the
> >>>> only way I currently have to get one out(!), but presumably it's because
> >>>> this omap-usb2 device is never registered?  Looks like this breaks
> >>>> non-dt USB on pandaboard; is that intended?
> >>>
> >>> Yes. omap-usb2 is *only* dt supported (New drivers shouldn't have the
> >>> old non-dt support).
> >>
> >> Well, USB used to work fine on Pandaboard without DT before the
> >> introduction of "omap-usb2", so one would expected it to continue
> >> working (until the board file is completely removed).
> >>
> >> Anyway, I've moved to DT now.
> >>
> >>> Some patches are queued only for 3.7.
> >>>
> >>> In case you want to use MUSB please use these patches on linux-next..
> >>> [PATCH v2] arm: omap: hwmod: make *phy_48m* as the main_clk of ocp2scp
> >>> [PATCH] ARM: OMAP2+: hwmod data: Fix ocp2scp_usb_phy and usb_host_hs
> >>> entries (from Benoit)
> >>> [PATCH 0/2] ARM: dts: Add subnode for ocp2scp (patch series)
> >>> [PATCH v3 0/3] ARM: dts: omap: add dt data for MUSB (patch series)
> >>
> >> I got these by merging in Benoit's for_3.7/dts_part2 on top of
> >> next-20120921.  Thanks.
> >> --
> >> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> >> the body of a message to majordomo at vger.kernel.org
> >> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> >>
> > 
> > I still can't get musb to work on 3.7-rc2. Apparently it is still
> > missing the patches from Benoit's for_3.7/dts_part2.
> > 
> > Maybe I just need to wait for it to be merged?
> 
> They are now in a for_3.8/dts. Unfortunately, one patch that was adding
> ctrl_module address in the USB data was rejected and thus I'm not sure
> it will work without that.
> 
> I think Tony had an idea to map the ctrl_register to regulator fmwk or
> something like that.

For device tree, we may be eventually able to handle the ctrl_register
using pinctrl-single.c and pinconf API. It probably does not make
sense to set it up as a regulator as the comparator can trigger errors
also for the pinconf related bits at least for MMC PBIAS.
 
> > Till then, where can I get a tree where musb works on Panda?

On panda, without using device tree, use v3.7-rc2 + the following patches:

ARM: OMAP: ocp2scp: create omap device for ocp2scp
ARM: OMAP4: add _dev_attr_ to ocp2scp for representing usb_phy
drivers: bus: ocp2scp: add pdata support

Also you need to enable CONFIG_OMAP_USB2. No idea what all is needed
to use MUSB with device tree at this point.

Regards,

Tony