[PATCH 2/2] arm: mvebu: adding SATA support: dt binding and config update

[Gregory CLEMENT]

On 10/24/2012 04:08 PM, Andrew Lunn wrote:
> On Wed, Oct 24, 2012 at 03:49:21PM +0200, Gregory CLEMENT wrote:
>> From: Lior Amsalem <alior at marvell.com>
>>
>> Signed-off-by: Gregory CLEMENT <gregory.clement at free-electrons.com>
>> Signed-off-by: Lior Amsalem <alior at marvell.com>
>> ---
>>  arch/arm/boot/dts/armada-370-db.dts  |    3 +++
>>  arch/arm/boot/dts/armada-370-xp.dtsi |   10 ++++++++++
>>  arch/arm/boot/dts/armada-xp-db.dts   |    3 +++
>>  arch/arm/configs/mvebu_defconfig     |    7 +++++++
>>  4 files changed, 23 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/armada-370-db.dts
>> index 4a31b03..2a2aa75 100644
>> --- a/arch/arm/boot/dts/armada-370-db.dts
>> +++ b/arch/arm/boot/dts/armada-370-db.dts
>> @@ -34,5 +34,8 @@
>>  			clock-frequency = <200000000>;
>>  			status = "okay";
>>  		};
>> +		sata at d00a0000 {
>> +			status = "okay";
>> +		};
>>  	};
>>  };
>> diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi
>> index 94b4b9e..3f08233 100644
>> --- a/arch/arm/boot/dts/armada-370-xp.dtsi
>> +++ b/arch/arm/boot/dts/armada-370-xp.dtsi
>> @@ -69,6 +69,16 @@
>>  			compatible = "marvell,armada-addr-decoding-controller";
>>  			reg = <0xd0020000 0x258>;
>>  		};
>> +
>> +		sata at d00a0000 {
>> +                        compatible = "marvell,orion-sata";
>> +                        reg = <0xd00a0000 0x2400>;
>> +                        interrupts = <55>;
>> +                        nr-ports = <2>;
>> +			clocks = <&coreclk 0>;//,  <&coreclk 0>;
>> +                        status = "disabled";
>> +		};
>> +
>>  	};
>>  };
>>  
>> diff --git a/arch/arm/boot/dts/armada-xp-db.dts b/arch/arm/boot/dts/armada-xp-db.dts
>> index b1fc728..b0db9a3 100644
>> --- a/arch/arm/boot/dts/armada-xp-db.dts
>> +++ b/arch/arm/boot/dts/armada-xp-db.dts
>> @@ -46,5 +46,8 @@
>>  			clock-frequency = <250000000>;
>>  			status = "okay";
>>  		};
>> +		sata at d00a0000 {
>> +			status = "okay";
>> +		};
>>  	};
>>  };
> 
> Hi Gregory
> 
> Should there be some pinctrl setup somewhere, to ensure the pins used
> for SATA are really setup up for SATA?

Yes you're right we should not depend of the bootloader configuration.

> 
> Also, for kirkwood, the number of SATA ports varies. So we don't
> define it in the base kirkwood.dtsi and leave each board to set it.
> Do we want to be consistent between kirkwood and 370/xp?

Yes sure. I will move it from dtsi to dts.

> 
> Thanks
>     Andrew
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> 


-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com