[PATCH 7/7] ARM: hw_breakpoint: use CRn as argument for debug reg accessor macros
Will Deacon
will.deacon at arm.com
Wed Oct 17 11:31:41 EDT 2012
From: Dietmar Eggemann <dietmar.eggemann at arm.com>
The coprocessor register CRn for accesses to the debug register can be a
different one than C0. Take this into account for the ARM_DBG_READ and
the ARM_DBG_WRITE macro.
The inline assembler calls which used a coprocessor register CRn other
than C0 are replaced by the ARM_DBG_READ or ARM_DBG_WRITE macro.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann at arm.com>
Signed-off-by: Will Deacon <will.deacon at arm.com>
---
arch/arm/include/asm/hw_breakpoint.h | 8 +++---
arch/arm/kernel/hw_breakpoint.c | 40 +++++++++++++++++-----------------
2 files changed, 24 insertions(+), 24 deletions(-)
diff --git a/arch/arm/include/asm/hw_breakpoint.h b/arch/arm/include/asm/hw_breakpoint.h
index c190bc9..01169dd 100644
--- a/arch/arm/include/asm/hw_breakpoint.h
+++ b/arch/arm/include/asm/hw_breakpoint.h
@@ -98,12 +98,12 @@ static inline void decode_ctrl_reg(u32 reg,
#define ARM_BASE_WCR 112
/* Accessor macros for the debug registers. */
-#define ARM_DBG_READ(M, OP2, VAL) do {\
- asm volatile("mrc p14, 0, %0, c0," #M ", " #OP2 : "=r" (VAL));\
+#define ARM_DBG_READ(N, M, OP2, VAL) do {\
+ asm volatile("mrc p14, 0, %0, " #N "," #M ", " #OP2 : "=r" (VAL));\
} while (0)
-#define ARM_DBG_WRITE(M, OP2, VAL) do {\
- asm volatile("mcr p14, 0, %0, c0," #M ", " #OP2 : : "r" (VAL));\
+#define ARM_DBG_WRITE(N, M, OP2, VAL) do {\
+ asm volatile("mcr p14, 0, %0, " #N "," #M ", " #OP2 : : "r" (VAL));\
} while (0)
struct notifier_block;
diff --git a/arch/arm/kernel/hw_breakpoint.c b/arch/arm/kernel/hw_breakpoint.c
index 3127ae4..05fdd68 100644
--- a/arch/arm/kernel/hw_breakpoint.c
+++ b/arch/arm/kernel/hw_breakpoint.c
@@ -52,14 +52,14 @@ static u8 debug_arch;
/* Maximum supported watchpoint length. */
static u8 max_watchpoint_len;
-#define READ_WB_REG_CASE(OP2, M, VAL) \
- case ((OP2 << 4) + M): \
- ARM_DBG_READ(c ## M, OP2, VAL); \
+#define READ_WB_REG_CASE(OP2, M, VAL) \
+ case ((OP2 << 4) + M): \
+ ARM_DBG_READ(c0, c ## M, OP2, VAL); \
break
-#define WRITE_WB_REG_CASE(OP2, M, VAL) \
- case ((OP2 << 4) + M): \
- ARM_DBG_WRITE(c ## M, OP2, VAL);\
+#define WRITE_WB_REG_CASE(OP2, M, VAL) \
+ case ((OP2 << 4) + M): \
+ ARM_DBG_WRITE(c0, c ## M, OP2, VAL); \
break
#define GEN_READ_WB_REG_CASES(OP2, VAL) \
@@ -140,7 +140,7 @@ static u8 get_debug_arch(void)
"Assuming v6 debug is present.\n"))
return ARM_DEBUG_ARCH_V6;
- ARM_DBG_READ(c0, 0, didr);
+ ARM_DBG_READ(c0, c0, 0, didr);
return (didr >> 16) & 0xf;
}
@@ -168,7 +168,7 @@ static int debug_exception_updates_fsr(void)
static int get_num_wrp_resources(void)
{
u32 didr;
- ARM_DBG_READ(c0, 0, didr);
+ ARM_DBG_READ(c0, c0, 0, didr);
return ((didr >> 28) & 0xf) + 1;
}
@@ -176,7 +176,7 @@ static int get_num_wrp_resources(void)
static int get_num_brp_resources(void)
{
u32 didr;
- ARM_DBG_READ(c0, 0, didr);
+ ARM_DBG_READ(c0, c0, 0, didr);
return ((didr >> 24) & 0xf) + 1;
}
@@ -230,14 +230,14 @@ static int get_num_brps(void)
static int monitor_mode_enabled(void)
{
u32 dscr;
- ARM_DBG_READ(c1, 0, dscr);
+ ARM_DBG_READ(c0, c1, 0, dscr);
return !!(dscr & ARM_DSCR_MDBGEN);
}
static int enable_monitor_mode(void)
{
u32 dscr;
- ARM_DBG_READ(c1, 0, dscr);
+ ARM_DBG_READ(c0, c1, 0, dscr);
/* If monitor mode is already enabled, just return. */
if (dscr & ARM_DSCR_MDBGEN)
@@ -247,11 +247,11 @@ static int enable_monitor_mode(void)
switch (get_debug_arch()) {
case ARM_DEBUG_ARCH_V6:
case ARM_DEBUG_ARCH_V6_1:
- ARM_DBG_WRITE(c1, 0, (dscr | ARM_DSCR_MDBGEN));
+ ARM_DBG_WRITE(c0, c1, 0, (dscr | ARM_DSCR_MDBGEN));
break;
case ARM_DEBUG_ARCH_V7_ECP14:
case ARM_DEBUG_ARCH_V7_1:
- ARM_DBG_WRITE(c2, 2, (dscr | ARM_DSCR_MDBGEN));
+ ARM_DBG_WRITE(c0, c2, 2, (dscr | ARM_DSCR_MDBGEN));
isb();
break;
default:
@@ -259,7 +259,7 @@ static int enable_monitor_mode(void)
}
/* Check that the write made it through. */
- ARM_DBG_READ(c1, 0, dscr);
+ ARM_DBG_READ(c0, c1, 0, dscr);
if (WARN_ONCE(!(dscr & ARM_DSCR_MDBGEN),
"Failed to enable monitor mode on CPU %d.\n",
smp_processor_id()))
@@ -852,7 +852,7 @@ static int hw_breakpoint_pending(unsigned long addr, unsigned int fsr,
local_irq_enable();
/* We only handle watchpoints and hardware breakpoints. */
- ARM_DBG_READ(c1, 0, dscr);
+ ARM_DBG_READ(c0, c1, 0, dscr);
/* Perform perf callbacks. */
switch (ARM_DSCR_MOE(dscr)) {
@@ -920,14 +920,14 @@ static void reset_ctrl_regs(void *unused)
* Ensure sticky power-down is clear (i.e. debug logic is
* powered up).
*/
- asm volatile("mrc p14, 0, %0, c1, c5, 4" : "=r" (dbg_power));
+ ARM_DBG_READ(c1, c5, 4, dbg_power);
if ((dbg_power & 0x1) == 0)
err = -EPERM;
/*
* Check whether we implement OS save and restore.
*/
- asm volatile("mrc p14, 0, %0, c1, c1, 4" : "=r" (dbg_power));
+ ARM_DBG_READ(c1, c1, 4, dbg_power);
if ((dbg_power & 0x9) == 0)
goto clear_vcr;
break;
@@ -935,7 +935,7 @@ static void reset_ctrl_regs(void *unused)
/*
* Ensure the OS double lock is clear.
*/
- asm volatile("mrc p14, 0, %0, c1, c3, 4" : "=r" (dbg_power));
+ ARM_DBG_READ(c1, c3, 4, dbg_power);
if ((dbg_power & 0x1) == 1)
err = -EPERM;
break;
@@ -951,7 +951,7 @@ static void reset_ctrl_regs(void *unused)
* Unconditionally clear the OS lock by writing a value
* other than 0xC5ACCE55 to the access register.
*/
- asm volatile("mcr p14, 0, %0, c1, c0, 4" : : "r" (0));
+ ARM_DBG_WRITE(c1, c0, 4, 0);
isb();
/*
@@ -959,7 +959,7 @@ static void reset_ctrl_regs(void *unused)
* enabling monitor mode.
*/
clear_vcr:
- asm volatile("mcr p14, 0, %0, c0, c7, 0" : : "r" (0));
+ ARM_DBG_WRITE(c0, c7, 0, 0);
isb();
if (cpumask_intersects(&debug_err_mask, cpumask_of(cpu))) {
--
1.7.4.1
More information about the linux-arm-kernel
mailing list