[PATCH v6] Enable USB peripheral mode on dm365 EVM

[Sergei Shtylyov]

Hello.

On 10-10-2012 14:33, Constantine Shulyupin wrote:

> From: Constantine Shulyupin <const at MakeLinux.com>
>
> Sets USB PHY clock source to 24 MHz clock and call USB configuration from board initialization.
>
> Tested with OTG configuration, usb gadget g_zero on DM365 EVM connected to PC.
>
> References:
>
> Definition of USB_PHY_CTRL and PHYCLKFREQ:
> - http://www.makelinux.com/lib/ti/DM36x_ARM/doc-141
>
> Original patch by miguel.aguilar at ridgerun.com three years ago:
> - http://www.mail-archive.com/davinci-linux-open-source@linux.davincidsp.com/msg14741.html
>
> Signed-off-by: Constantine Shulyupin <const at MakeLinux.com>
> ---
>
> Note:
>
> Changelog
>
> Changes since v5 http://www.spinics.net/lists/kernel/msg1413120.html
> accordingy feedback of nsekhar at ti.com http://www.spinics.net/lists/kernel/msg1414914.html
> - phy configuration moved to drivers/usb/musb/davinci.c
> - USB_OTG configuration is submitted in separated patch: http://www.spinics.net/lists/kernel/msg1414964.html
> - Setting current limit to 1000 mA. Any way the current is limited to 510 mA in davinci_setup_usb.
>
> Changes since v4 http://www.spinics.net/lists/kernel/msg1412995.html
> - removed fix of dev_info in musb_init_controller
>
> Changes since v3 http://www.spinics.net/lists/kernel/msg1412544.html:
> - removed optional altering of pr_info
>
> Changes since v1  http://marc.info/?l=linux-kernel&m=130894150803661&w=2:
> - removed optional code and reordered
> - removed alternation of GPIO33, which is multiplexed with DRVVBUS, because is not need for peripheral USB
>
> This patch is based on code from projects Arago, Angstom and RidgeRun.
>
> ---
>   arch/arm/mach-davinci/board-dm365-evm.c |    2 ++
>   drivers/usb/musb/davinci.c              |    3 +++
>   drivers/usb/musb/davinci.h              |    1 +
>   3 files changed, 6 insertions(+)
>
> diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c
> index 688a9c5..ba5ffc1 100644
> --- a/arch/arm/mach-davinci/board-dm365-evm.c
> +++ b/arch/arm/mach-davinci/board-dm365-evm.c
> @@ -38,6 +38,7 @@
>   #include <mach/mmc.h>
>   #include <mach/nand.h>
>   #include <mach/keyscan.h>
> +#include <mach/usb.h>
>   
>   #include <media/tvp514x.h>
>   
> @@ -610,6 +611,7 @@ static __init void dm365_evm_init(void)
>   
>   	dm365_init_spi0(BIT(0), dm365_evm_spi_info,
>   			ARRAY_SIZE(dm365_evm_spi_info));
> +	davinci_setup_usb(1000, 8);
>   }
>   
>   MACHINE_START(DAVINCI_DM365_EVM, "DaVinci DM365 EVM")

     You need to split the patch at this point. Above part should be 
applied to the DaVinci tree, below part to the MUSB tree.

> diff --git a/drivers/usb/musb/davinci.c b/drivers/usb/musb/davinci.c
> index 472c8b4..af09ebf 100644
> --- a/drivers/usb/musb/davinci.c
> +++ b/drivers/usb/musb/davinci.c
> @@ -428,6 +428,9 @@ static int davinci_musb_init(struct musb *musb)
>   		__raw_writel(deepsleep, DM355_DEEPSLEEP);
>   	}
>   
> +	if (machine_is_davinci_dm365_evm())
> +		writel(readl(USB_PHY_CTRL) | USBPHY_CLKFREQ_24MHZ, USB_PHY_CTRL);

     I'd put that to the board file instead, like in board-da830-evm.c....

WBR, Sergei