[PATCH v2 13/14] ARM: OMAP2+: gpmc: remove exported nand functions
Afzal Mohammed
afzal at ti.com
Mon Oct 8 01:38:03 EDT 2012
nand driver handles gpmc-nand block fully, hence no more
users for these exported nand functions, remove it.
Signed-off-by: Afzal Mohammed <afzal at ti.com>
---
arch/arm/mach-omap2/gpmc.c | 432 ---------------------------------
arch/arm/plat-omap/include/plat/gpmc.h | 31 ---
2 files changed, 463 deletions(-)
diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c
index eb577c5..1121248 100644
--- a/arch/arm/mach-omap2/gpmc.c
+++ b/arch/arm/mach-omap2/gpmc.c
@@ -150,7 +150,6 @@ static struct resource gpmc_mem_root;
static struct resource gpmc_cs_mem[GPMC_CS_NUM];
static DEFINE_SPINLOCK(gpmc_mem_lock);
static unsigned int gpmc_cs_map; /* flag for cs which are initialized */
-static int gpmc_ecc_used = -EINVAL; /* cs using ecc engine */
static struct device *gpmc_dev;
static int gpmc_irq;
static resource_size_t phys_base, mem_size;
@@ -171,22 +170,6 @@ static u32 gpmc_read_reg(int idx)
return __raw_readl(gpmc_base + idx);
}
-static void gpmc_cs_write_byte(int cs, int idx, u8 val)
-{
- void __iomem *reg_addr;
-
- reg_addr = gpmc_base + GPMC_CS0_OFFSET + (cs * GPMC_CS_SIZE) + idx;
- __raw_writeb(val, reg_addr);
-}
-
-static u8 gpmc_cs_read_byte(int cs, int idx)
-{
- void __iomem *reg_addr;
-
- reg_addr = gpmc_base + GPMC_CS0_OFFSET + (cs * GPMC_CS_SIZE) + idx;
- return __raw_readb(reg_addr);
-}
-
void gpmc_cs_write_reg(int cs, int idx, u32 val)
{
void __iomem *reg_addr;
@@ -563,44 +546,6 @@ void gpmc_cs_free(int cs)
EXPORT_SYMBOL(gpmc_cs_free);
/**
- * gpmc_read_status - read access request to get the different gpmc status
- * @cmd: command type
- * @return status
- */
-int gpmc_read_status(int cmd)
-{
- int status = -EINVAL;
- u32 regval = 0;
-
- switch (cmd) {
- case GPMC_GET_IRQ_STATUS:
- status = gpmc_read_reg(GPMC_IRQSTATUS);
- break;
-
- case GPMC_PREFETCH_FIFO_CNT:
- regval = gpmc_read_reg(GPMC_PREFETCH_STATUS);
- status = GPMC_PREFETCH_STATUS_FIFO_CNT(regval);
- break;
-
- case GPMC_PREFETCH_COUNT:
- regval = gpmc_read_reg(GPMC_PREFETCH_STATUS);
- status = GPMC_PREFETCH_STATUS_COUNT(regval);
- break;
-
- case GPMC_STATUS_BUFFER:
- regval = gpmc_read_reg(GPMC_STATUS);
- /* 1 : buffer is available to write */
- status = regval & GPMC_STATUS_BUFF_EMPTY;
- break;
-
- default:
- printk(KERN_ERR "gpmc_read_status: Not supported\n");
- }
- return status;
-}
-EXPORT_SYMBOL(gpmc_read_status);
-
-/**
* gpmc_cs_configure - write request to configure gpmc
* @cs: chip select number
* @cmd: command type
@@ -668,119 +613,6 @@ int gpmc_cs_configure(int cs, int cmd, int wval)
}
EXPORT_SYMBOL(gpmc_cs_configure);
-/**
- * gpmc_nand_read - nand specific read access request
- * @cs: chip select number
- * @cmd: command type
- */
-int gpmc_nand_read(int cs, int cmd)
-{
- int rval = -EINVAL;
-
- switch (cmd) {
- case GPMC_NAND_DATA:
- rval = gpmc_cs_read_byte(cs, GPMC_CS_NAND_DATA);
- break;
-
- default:
- printk(KERN_ERR "gpmc_read_nand_ctrl: Not supported\n");
- }
- return rval;
-}
-EXPORT_SYMBOL(gpmc_nand_read);
-
-/**
- * gpmc_nand_write - nand specific write request
- * @cs: chip select number
- * @cmd: command type
- * @wval: value to write
- */
-int gpmc_nand_write(int cs, int cmd, int wval)
-{
- int err = 0;
-
- switch (cmd) {
- case GPMC_NAND_COMMAND:
- gpmc_cs_write_byte(cs, GPMC_CS_NAND_COMMAND, wval);
- break;
-
- case GPMC_NAND_ADDRESS:
- gpmc_cs_write_byte(cs, GPMC_CS_NAND_ADDRESS, wval);
- break;
-
- case GPMC_NAND_DATA:
- gpmc_cs_write_byte(cs, GPMC_CS_NAND_DATA, wval);
-
- default:
- printk(KERN_ERR "gpmc_write_nand_ctrl: Not supported\n");
- err = -EINVAL;
- }
- return err;
-}
-EXPORT_SYMBOL(gpmc_nand_write);
-
-
-
-/**
- * gpmc_prefetch_enable - configures and starts prefetch transfer
- * @cs: cs (chip select) number
- * @fifo_th: fifo threshold to be used for read/ write
- * @dma_mode: dma mode enable (1) or disable (0)
- * @u32_count: number of bytes to be transferred
- * @is_write: prefetch read(0) or write post(1) mode
- */
-int gpmc_prefetch_enable(int cs, int fifo_th, int dma_mode,
- unsigned int u32_count, int is_write)
-{
-
- if (fifo_th > PREFETCH_FIFOTHRESHOLD_MAX) {
- pr_err("gpmc: fifo threshold is not supported\n");
- return -1;
- } else if (!(gpmc_read_reg(GPMC_PREFETCH_CONTROL))) {
- /* Set the amount of bytes to be prefetched */
- gpmc_write_reg(GPMC_PREFETCH_CONFIG2, u32_count);
-
- /* Set dma/mpu mode, the prefetch read / post write and
- * enable the engine. Set which cs is has requested for.
- */
- gpmc_write_reg(GPMC_PREFETCH_CONFIG1, ((cs << CS_NUM_SHIFT) |
- PREFETCH_FIFOTHRESHOLD(fifo_th) |
- ENABLE_PREFETCH |
- (dma_mode << DMA_MPU_MODE) |
- (0x1 & is_write)));
-
- /* Start the prefetch engine */
- gpmc_write_reg(GPMC_PREFETCH_CONTROL, 0x1);
- } else {
- return -EBUSY;
- }
-
- return 0;
-}
-EXPORT_SYMBOL(gpmc_prefetch_enable);
-
-/**
- * gpmc_prefetch_reset - disables and stops the prefetch engine
- */
-int gpmc_prefetch_reset(int cs)
-{
- u32 config1;
-
- /* check if the same module/cs is trying to reset */
- config1 = gpmc_read_reg(GPMC_PREFETCH_CONFIG1);
- if (((config1 >> CS_NUM_SHIFT) & 0x7) != cs)
- return -EINVAL;
-
- /* Stop the PFPW engine */
- gpmc_write_reg(GPMC_PREFETCH_CONTROL, 0x0);
-
- /* Reset/disable the PFPW engine */
- gpmc_write_reg(GPMC_PREFETCH_CONFIG1, 0x0);
-
- return 0;
-}
-EXPORT_SYMBOL(gpmc_prefetch_reset);
-
void gpmc_update_nand_reg(struct gpmc_nand_regs *reg, int cs)
{
int i;
@@ -1145,267 +977,3 @@ void omap3_gpmc_restore_context(void)
}
}
#endif /* CONFIG_ARCH_OMAP3 */
-
-/**
- * gpmc_enable_hwecc - enable hardware ecc functionality
- * @cs: chip select number
- * @mode: read/write mode
- * @dev_width: device bus width(1 for x16, 0 for x8)
- * @ecc_size: bytes for which ECC will be generated
- */
-int gpmc_enable_hwecc(int cs, int mode, int dev_width, int ecc_size)
-{
- unsigned int val;
-
- /* check if ecc module is in used */
- if (gpmc_ecc_used != -EINVAL)
- return -EINVAL;
-
- gpmc_ecc_used = cs;
-
- /* clear ecc and enable bits */
- gpmc_write_reg(GPMC_ECC_CONTROL,
- GPMC_ECC_CTRL_ECCCLEAR |
- GPMC_ECC_CTRL_ECCREG1);
-
- /* program ecc and result sizes */
- val = ((((ecc_size >> 1) - 1) << 22) | (0x0000000F));
- gpmc_write_reg(GPMC_ECC_SIZE_CONFIG, val);
-
- switch (mode) {
- case GPMC_ECC_READ:
- case GPMC_ECC_WRITE:
- gpmc_write_reg(GPMC_ECC_CONTROL,
- GPMC_ECC_CTRL_ECCCLEAR |
- GPMC_ECC_CTRL_ECCREG1);
- break;
- case GPMC_ECC_READSYN:
- gpmc_write_reg(GPMC_ECC_CONTROL,
- GPMC_ECC_CTRL_ECCCLEAR |
- GPMC_ECC_CTRL_ECCDISABLE);
- break;
- default:
- printk(KERN_INFO "Error: Unrecognized Mode[%d]!\n", mode);
- break;
- }
-
- /* (ECC 16 or 8 bit col) | ( CS ) | ECC Enable */
- val = (dev_width << 7) | (cs << 1) | (0x1);
- gpmc_write_reg(GPMC_ECC_CONFIG, val);
- return 0;
-}
-EXPORT_SYMBOL_GPL(gpmc_enable_hwecc);
-
-/**
- * gpmc_calculate_ecc - generate non-inverted ecc bytes
- * @cs: chip select number
- * @dat: data pointer over which ecc is computed
- * @ecc_code: ecc code buffer
- *
- * Using non-inverted ECC is considered ugly since writing a blank
- * page (padding) will clear the ECC bytes. This is not a problem as long
- * no one is trying to write data on the seemingly unused page. Reading
- * an erased page will produce an ECC mismatch between generated and read
- * ECC bytes that has to be dealt with separately.
- */
-int gpmc_calculate_ecc(int cs, const u_char *dat, u_char *ecc_code)
-{
- unsigned int val = 0x0;
-
- if (gpmc_ecc_used != cs)
- return -EINVAL;
-
- /* read ecc result */
- val = gpmc_read_reg(GPMC_ECC1_RESULT);
- *ecc_code++ = val; /* P128e, ..., P1e */
- *ecc_code++ = val >> 16; /* P128o, ..., P1o */
- /* P2048o, P1024o, P512o, P256o, P2048e, P1024e, P512e, P256e */
- *ecc_code++ = ((val >> 8) & 0x0f) | ((val >> 20) & 0xf0);
-
- gpmc_ecc_used = -EINVAL;
- return 0;
-}
-EXPORT_SYMBOL_GPL(gpmc_calculate_ecc);
-
-#ifdef CONFIG_ARCH_OMAP3
-
-/**
- * gpmc_init_hwecc_bch - initialize hardware BCH ecc functionality
- * @cs: chip select number
- * @nsectors: how many 512-byte sectors to process
- * @nerrors: how many errors to correct per sector (4 or 8)
- *
- * This function must be executed before any call to gpmc_enable_hwecc_bch.
- */
-int gpmc_init_hwecc_bch(int cs, int nsectors, int nerrors)
-{
- /* check if ecc module is in use */
- if (gpmc_ecc_used != -EINVAL)
- return -EINVAL;
-
- /* support only OMAP3 class */
- if (!cpu_is_omap34xx()) {
- printk(KERN_ERR "BCH ecc is not supported on this CPU\n");
- return -EINVAL;
- }
-
- /*
- * For now, assume 4-bit mode is only supported on OMAP3630 ES1.x, x>=1.
- * Other chips may be added if confirmed to work.
- */
- if ((nerrors == 4) &&
- (!cpu_is_omap3630() || (GET_OMAP_REVISION() == 0))) {
- printk(KERN_ERR "BCH 4-bit mode is not supported on this CPU\n");
- return -EINVAL;
- }
-
- /* sanity check */
- if (nsectors > 8) {
- printk(KERN_ERR "BCH cannot process %d sectors (max is 8)\n",
- nsectors);
- return -EINVAL;
- }
-
- return 0;
-}
-EXPORT_SYMBOL_GPL(gpmc_init_hwecc_bch);
-
-/**
- * gpmc_enable_hwecc_bch - enable hardware BCH ecc functionality
- * @cs: chip select number
- * @mode: read/write mode
- * @dev_width: device bus width(1 for x16, 0 for x8)
- * @nsectors: how many 512-byte sectors to process
- * @nerrors: how many errors to correct per sector (4 or 8)
- */
-int gpmc_enable_hwecc_bch(int cs, int mode, int dev_width, int nsectors,
- int nerrors)
-{
- unsigned int val;
-
- /* check if ecc module is in use */
- if (gpmc_ecc_used != -EINVAL)
- return -EINVAL;
-
- gpmc_ecc_used = cs;
-
- /* clear ecc and enable bits */
- gpmc_write_reg(GPMC_ECC_CONTROL, 0x1);
-
- /*
- * When using BCH, sector size is hardcoded to 512 bytes.
- * Here we are using wrapping mode 6 both for reading and writing, with:
- * size0 = 0 (no additional protected byte in spare area)
- * size1 = 32 (skip 32 nibbles = 16 bytes per sector in spare area)
- */
- gpmc_write_reg(GPMC_ECC_SIZE_CONFIG, (32 << 22) | (0 << 12));
-
- /* BCH configuration */
- val = ((1 << 16) | /* enable BCH */
- (((nerrors == 8) ? 1 : 0) << 12) | /* 8 or 4 bits */
- (0x06 << 8) | /* wrap mode = 6 */
- (dev_width << 7) | /* bus width */
- (((nsectors-1) & 0x7) << 4) | /* number of sectors */
- (cs << 1) | /* ECC CS */
- (0x1)); /* enable ECC */
-
- gpmc_write_reg(GPMC_ECC_CONFIG, val);
- gpmc_write_reg(GPMC_ECC_CONTROL, 0x101);
- return 0;
-}
-EXPORT_SYMBOL_GPL(gpmc_enable_hwecc_bch);
-
-/**
- * gpmc_calculate_ecc_bch4 - Generate 7 ecc bytes per sector of 512 data bytes
- * @cs: chip select number
- * @dat: The pointer to data on which ecc is computed
- * @ecc: The ecc output buffer
- */
-int gpmc_calculate_ecc_bch4(int cs, const u_char *dat, u_char *ecc)
-{
- int i;
- unsigned long nsectors, reg, val1, val2;
-
- if (gpmc_ecc_used != cs)
- return -EINVAL;
-
- nsectors = ((gpmc_read_reg(GPMC_ECC_CONFIG) >> 4) & 0x7) + 1;
-
- for (i = 0; i < nsectors; i++) {
-
- reg = GPMC_ECC_BCH_RESULT_0 + 16*i;
-
- /* Read hw-computed remainder */
- val1 = gpmc_read_reg(reg + 0);
- val2 = gpmc_read_reg(reg + 4);
-
- /*
- * Add constant polynomial to remainder, in order to get an ecc
- * sequence of 0xFFs for a buffer filled with 0xFFs; and
- * left-justify the resulting polynomial.
- */
- *ecc++ = 0x28 ^ ((val2 >> 12) & 0xFF);
- *ecc++ = 0x13 ^ ((val2 >> 4) & 0xFF);
- *ecc++ = 0xcc ^ (((val2 & 0xF) << 4)|((val1 >> 28) & 0xF));
- *ecc++ = 0x39 ^ ((val1 >> 20) & 0xFF);
- *ecc++ = 0x96 ^ ((val1 >> 12) & 0xFF);
- *ecc++ = 0xac ^ ((val1 >> 4) & 0xFF);
- *ecc++ = 0x7f ^ ((val1 & 0xF) << 4);
- }
-
- gpmc_ecc_used = -EINVAL;
- return 0;
-}
-EXPORT_SYMBOL_GPL(gpmc_calculate_ecc_bch4);
-
-/**
- * gpmc_calculate_ecc_bch8 - Generate 13 ecc bytes per block of 512 data bytes
- * @cs: chip select number
- * @dat: The pointer to data on which ecc is computed
- * @ecc: The ecc output buffer
- */
-int gpmc_calculate_ecc_bch8(int cs, const u_char *dat, u_char *ecc)
-{
- int i;
- unsigned long nsectors, reg, val1, val2, val3, val4;
-
- if (gpmc_ecc_used != cs)
- return -EINVAL;
-
- nsectors = ((gpmc_read_reg(GPMC_ECC_CONFIG) >> 4) & 0x7) + 1;
-
- for (i = 0; i < nsectors; i++) {
-
- reg = GPMC_ECC_BCH_RESULT_0 + 16*i;
-
- /* Read hw-computed remainder */
- val1 = gpmc_read_reg(reg + 0);
- val2 = gpmc_read_reg(reg + 4);
- val3 = gpmc_read_reg(reg + 8);
- val4 = gpmc_read_reg(reg + 12);
-
- /*
- * Add constant polynomial to remainder, in order to get an ecc
- * sequence of 0xFFs for a buffer filled with 0xFFs.
- */
- *ecc++ = 0xef ^ (val4 & 0xFF);
- *ecc++ = 0x51 ^ ((val3 >> 24) & 0xFF);
- *ecc++ = 0x2e ^ ((val3 >> 16) & 0xFF);
- *ecc++ = 0x09 ^ ((val3 >> 8) & 0xFF);
- *ecc++ = 0xed ^ (val3 & 0xFF);
- *ecc++ = 0x93 ^ ((val2 >> 24) & 0xFF);
- *ecc++ = 0x9a ^ ((val2 >> 16) & 0xFF);
- *ecc++ = 0xc2 ^ ((val2 >> 8) & 0xFF);
- *ecc++ = 0x97 ^ (val2 & 0xFF);
- *ecc++ = 0x79 ^ ((val1 >> 24) & 0xFF);
- *ecc++ = 0xe5 ^ ((val1 >> 16) & 0xFF);
- *ecc++ = 0x24 ^ ((val1 >> 8) & 0xFF);
- *ecc++ = 0xb5 ^ (val1 & 0xFF);
- }
-
- gpmc_ecc_used = -EINVAL;
- return 0;
-}
-EXPORT_SYMBOL_GPL(gpmc_calculate_ecc_bch8);
-
-#endif /* CONFIG_ARCH_OMAP3 */
diff --git a/arch/arm/plat-omap/include/plat/gpmc.h b/arch/arm/plat-omap/include/plat/gpmc.h
index 17fc1e7..e08a51a 100644
--- a/arch/arm/plat-omap/include/plat/gpmc.h
+++ b/arch/arm/plat-omap/include/plat/gpmc.h
@@ -34,15 +34,6 @@
#define GPMC_SET_IRQ_STATUS 0x00000004
#define GPMC_CONFIG_WP 0x00000005
-#define GPMC_GET_IRQ_STATUS 0x00000006
-#define GPMC_PREFETCH_FIFO_CNT 0x00000007 /* bytes available in FIFO for r/w */
-#define GPMC_PREFETCH_COUNT 0x00000008 /* remaining bytes to be read/write*/
-#define GPMC_STATUS_BUFFER 0x00000009 /* 1: buffer is available to write */
-
-#define GPMC_NAND_COMMAND 0x0000000a
-#define GPMC_NAND_ADDRESS 0x0000000b
-#define GPMC_NAND_DATA 0x0000000c
-
#define GPMC_ENABLE_IRQ 0x0000000d
/* ECC commands */
@@ -78,15 +69,10 @@
#define GPMC_DEVICETYPE_NOR 0
#define GPMC_DEVICETYPE_NAND 2
#define GPMC_CONFIG_WRITEPROTECT 0x00000010
-#define GPMC_STATUS_BUFF_EMPTY 0x00000001
#define WR_RD_PIN_MONITORING 0x00600000
-#define GPMC_PREFETCH_STATUS_FIFO_CNT(val) ((val >> 24) & 0x7F)
-#define GPMC_PREFETCH_STATUS_COUNT(val) (val & 0x00003fff)
#define GPMC_IRQ_FIFOEVENTENABLE 0x01
#define GPMC_IRQ_COUNT_EVENT 0x02
-#define PREFETCH_FIFOTHRESHOLD_MAX 0x40
-#define PREFETCH_FIFOTHRESHOLD(val) ((val) << 8)
/* bool type time settings */
struct gpmc_bool_timings {
@@ -161,25 +147,8 @@ extern int gpmc_cs_request(int cs, unsigned long size, unsigned long *base);
extern void gpmc_cs_free(int cs);
extern int gpmc_cs_set_reserved(int cs, int reserved);
extern int gpmc_cs_reserved(int cs);
-extern int gpmc_prefetch_enable(int cs, int fifo_th, int dma_mode,
- unsigned int u32_count, int is_write);
-extern int gpmc_prefetch_reset(int cs);
extern void omap3_gpmc_save_context(void);
extern void omap3_gpmc_restore_context(void);
-extern int gpmc_read_status(int cmd);
extern int gpmc_cs_configure(int cs, int cmd, int wval);
-extern int gpmc_nand_read(int cs, int cmd);
-extern int gpmc_nand_write(int cs, int cmd, int wval);
-
-int gpmc_enable_hwecc(int cs, int mode, int dev_width, int ecc_size);
-int gpmc_calculate_ecc(int cs, const u_char *dat, u_char *ecc_code);
-
-#ifdef CONFIG_ARCH_OMAP3
-int gpmc_init_hwecc_bch(int cs, int nsectors, int nerrors);
-int gpmc_enable_hwecc_bch(int cs, int mode, int dev_width, int nsectors,
- int nerrors);
-int gpmc_calculate_ecc_bch4(int cs, const u_char *dat, u_char *ecc);
-int gpmc_calculate_ecc_bch8(int cs, const u_char *dat, u_char *ecc);
-#endif /* CONFIG_ARCH_OMAP3 */
#endif
--
1.7.12
More information about the linux-arm-kernel
mailing list