[PATCH 6/9] usb: chipidea: add PTW and PTS handling

Matthieu CASTET matthieu.castet at parrot.com
Wed Nov 21 11:06:26 EST 2012


Michael Grzeschik a écrit :
> On Fri, Nov 16, 2012 at 05:39:42PM +0200, Alexander Shishkin wrote:
>> Matthieu CASTET <matthieu.castet at parrot.com> writes:
>>
>>> Alexander Shishkin a écrit :
>>>> Michael Grzeschik <mgr at pengutronix.de> writes:
>>>>
>>>>> On Fri, Nov 16, 2012 at 03:34:23PM +0200, Alexander Shishkin wrote:
>>>>>> Michael Grzeschik <mgr at pengutronix.de> writes:
>>>>>>
>>>>>>> On Fri, Nov 16, 2012 at 02:45:39PM +0200, Alexander Shishkin wrote:
>>>>>>>> Michael Grzeschik <m.grzeschik at pengutronix.de> writes:
>>>>>>>>
>>>>>>>>> This patch makes it possible to configure the PTW and PTS bits inside
>>>>>>>>> the portsc register for host and device mode before the driver starts
>>>>>>>>> and the phy can be addressed as hardware implementation is designed.
>>>>>>>>>
>>>>>>>>> Signed-off-by: Michael Grzeschik <m.grzeschik at pengutronix.de>
>>>>>>>>> Signed-off-by: Marc Kleine-Budde <mkl at pengutronix.de>
>>>>>>>>> ---
>>>>>>>>>  drivers/usb/chipidea/bits.h        |    3 +++
>>>>>>>>>  drivers/usb/chipidea/ci.h          |    2 ++
>>>>>>>>>  drivers/usb/chipidea/ci13xxx_imx.c |    1 +
>>>>>>>>>  drivers/usb/chipidea/core.c        |   47 ++++++++++++++++++++++++++++++++++++
>>>>>>>>>  drivers/usb/chipidea/host.c        |    4 +++
>>>>>>>>>  include/linux/usb/chipidea.h       |    9 +++++++
>>>>>>>>>  6 files changed, 66 insertions(+)
>>>>>>>>>
>>>>>>>>> diff --git a/drivers/usb/chipidea/bits.h b/drivers/usb/chipidea/bits.h
>>>>>>>>> index 4b6ae3e..3cded5f 100644
>>>>>>>>> --- a/drivers/usb/chipidea/bits.h
>>>>>>>>> +++ b/drivers/usb/chipidea/bits.h
>>>>>>>>> @@ -48,6 +48,9 @@
>>>>>>>>>  #define PORTSC_SUSP           BIT(7)
>>>>>>>>>  #define PORTSC_HSP            BIT(9)
>>>>>>>>>  #define PORTSC_PTC            (0x0FUL << 16)
>>>>>>>>> +#define PORTSC_PTS            (BIT(31) | BIT(30))
>>>>>>>>> +#define PORTSC_PTW            BIT(28)
>>>>>>>>> +#define PORTSC_STS            BIT(29)
>>>>>>>> Hm, my spec says these are actually in DEVLC register and only have this
>>>>>>>> meaning in device mode. And in portsc these bits fall in device address
>>>>>>>> bitfield. Can you refer me to your spec?
>>>>>>> You can find it here:
>>>>>>> http://cache.freescale.com/files/32bit/doc/ref_manual/iMX53RM.pdf?fpsp=1
>>>>>>> Page 4947
>>>>>> Oh, but see, the offset is 0x184, which in chipidea spec (the version
>>>>>> that I have) corresponds to DEVLC and not PORTSC. So in this driver's
>>>>>> terminology it's DEVLC too, at least currently.
>>>>>>
>>>>>> So have you tested this code and did it make any difference?
>>>>> Yes, i have tested this code with MX25, MX28, MX35 and MX53. In every
>>>>> SoCs Datasheet the PORTSC register is defined on PORTBASE+0x184. Without
>>>>> this proper configuration its not possible to communicate with the PHY.
>>>> No, I mean, you're writing DEVLC (using present driver's terminology)
>>>> bits to PORTSC register. It *shouldn't* work. I suppose, it does
>>>> something, but not exactly what you intended.
>>>>
>>> I confirm in our datasheet we have PTW, PTS, STS in this register  PORTSCx with
>>> this mapping.
>>>
>>> In later design that support lpm, these bits have to move in another register
>>> because ehci 1.1 use them [1].
>> Ahh, I didn't realize imxes were nolpm. Now it makes more sense. This
>> means that, as you suggested in the other mail, these portsc/devlc
>> accesses should be done conditionally based on ci->hw_bank.lpm.
> 
> To handle lpm devices in this patch, we need some register layout of the
> lpm core. Probably only te DEVLC register. Is there some documentation
> available?

In include/linux/usb/langwell_udc.h before it was removed, you could find the
mapping :

    u32 devlc;      /* control LPM and each USB port behavior */
/* bits 31:29, parallel transceiver select */
#define LPM_PTS(d)  (((d)>>29)&7)
#define LPM_STS     BIT(28) /* serial transceiver select */
#define LPM_PTW     BIT(27) /* parallel transceiver width */
#define LPM_PSPD(d) (((d)>>25)&3)   /* bits 26:25, port speed */
#define LPM_PSPD_MASK   (BIT(26) | BIT(25))
#define LPM_SPEED_FULL  0
#define LPM_SPEED_LOW   1
#define LPM_SPEED_HIGH  2
#define LPM_SRT     BIT(24) /* shorten reset time */
#define LPM_PFSC    BIT(23) /* port force full speed connect */
#define LPM_PHCD    BIT(22) /* PHY low power suspend clock disable */
#define LPM_STL     BIT(16) /* STALL reply to LPM token */
#define LPM_BA(d)   \
    (((d)>>1)&0x7ff)    /* bits 11:1, BmAttributes */
#define LPM_NYT_ACK BIT(0)  /* NYET/ACK reply to LPM token */



More information about the linux-arm-kernel mailing list