[PATCH v2 08/14] ARM: Kirkwood: Convert dreamplug to pinctrl.
Andrew Lunn
andrew at lunn.ch
Sat Nov 17 11:00:50 EST 2012
Signed-off-by: Andrew Lunn <andrew at lunn.ch>
---
arch/arm/boot/dts/kirkwood-dreamplug.dts | 21 +++++++++++++++++++++
arch/arm/mach-kirkwood/board-dreamplug.c | 14 --------------
2 files changed, 21 insertions(+), 14 deletions(-)
diff --git a/arch/arm/boot/dts/kirkwood-dreamplug.dts b/arch/arm/boot/dts/kirkwood-dreamplug.dts
index 26e281f..f2d386c 100644
--- a/arch/arm/boot/dts/kirkwood-dreamplug.dts
+++ b/arch/arm/boot/dts/kirkwood-dreamplug.dts
@@ -1,6 +1,7 @@
/dts-v1/;
/include/ "kirkwood.dtsi"
+/include/ "kirkwood-6281.dtsi"
/ {
model = "Globalscale Technologies Dreamplug";
@@ -16,6 +17,26 @@
};
ocp at f1000000 {
+ pinctrl: pinctrl at 10000 {
+
+ pinctrl-0 = < &pmx_spi
+ &pmx_led_bluetooth &pmx_led_wifi
+ &pmx_led_wifi_ap >;
+ pinctrl-names = "default";
+
+ pmx_led_bluetooth: pmx-led-bluetooth {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ pmx_led_wifi: pmx-led-wifi {
+ marvell,pins = "mpp48";
+ marvell,function = "gpio";
+ };
+ pmx_led_wifi_ap: pmx-led-wifi-ap {
+ marvell,pins = "mpp49";
+ marvell,function = "gpio";
+ };
+ };
serial at 12000 {
clock-frequency = <200000000>;
status = "ok";
diff --git a/arch/arm/mach-kirkwood/board-dreamplug.c b/arch/arm/mach-kirkwood/board-dreamplug.c
index 20af53a..db0c280 100644
--- a/arch/arm/mach-kirkwood/board-dreamplug.c
+++ b/arch/arm/mach-kirkwood/board-dreamplug.c
@@ -32,7 +32,6 @@
#include <mach/bridge-regs.h>
#include <linux/platform_data/mmc-mvsdio.h>
#include "common.h"
-#include "mpp.h"
static struct mv643xx_eth_platform_data dreamplug_ge00_data = {
.phy_addr = MV643XX_ETH_PHY_ADDR(0),
@@ -46,24 +45,11 @@ static struct mvsdio_platform_data dreamplug_mvsdio_data = {
/* unfortunately the CD signal has not been connected */
};
-static unsigned int dreamplug_mpp_config[] __initdata = {
- MPP0_SPI_SCn,
- MPP1_SPI_MOSI,
- MPP2_SPI_SCK,
- MPP3_SPI_MISO,
- MPP47_GPIO, /* Bluetooth LED */
- MPP48_GPIO, /* Wifi LED */
- MPP49_GPIO, /* Wifi AP LED */
- 0
-};
-
void __init dreamplug_init(void)
{
/*
* Basic setup. Needs to be called early.
*/
- kirkwood_mpp_conf(dreamplug_mpp_config);
-
kirkwood_ehci_init();
kirkwood_ge00_init(&dreamplug_ge00_data);
kirkwood_ge01_init(&dreamplug_ge01_data);
--
1.7.10.4
More information about the linux-arm-kernel
mailing list