[PATCH 1/1] arm: at91: add Ronetix pm9g45 board support

Jean-Christophe PLAGNIOL-VILLARD plagnioj at jcrosoft.com
Fri Nov 16 08:28:19 EST 2012


On 14:08 Fri 16 Nov     , Nicolas Ferre wrote:
> On 10/19/2012 04:19 AM, Jean-Christophe PLAGNIOL-VILLARD :
> > CPU Module with ATMEL AT91SAM9G45
> > http://www.ronetix.at/pm9g45.html
> > 
> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
> > Cc: Nicolas Ferre <nicolas.ferre at atmel.com>
> 
> Ok, queued in at91-3.8-dt branch.
> 
> I had to modify the Makefile part of it to match current move to
> arch/arm/boot/dts/Makefile.
> 
> Acked-by: Nicolas Ferre <nicolas.ferre at atmel.com>
I prefer to go via linus W I've other updte for the macb on the top of it

ditto for the rm9200

Best Regards,
J.
> 
> > ---
> >  arch/arm/boot/dts/Makefile   |    1 +
> >  arch/arm/boot/dts/pm9g45.dts |  144 ++++++++++++++++++++++++++++++++++++++++++
> >  2 files changed, 145 insertions(+)
> >  create mode 100644 arch/arm/boot/dts/pm9g45.dts
> > 
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index a9b051a..627b6ad 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_AT91) += tny_a9g20.dtb
> >  dtb-$(CONFIG_ARCH_AT91) += usb_a9g20.dtb
> >  # sam9g45
> >  dtb-$(CONFIG_ARCH_AT91) += at91sam9m10g45ek.dtb
> > +dtb-$(CONFIG_ARCH_AT91) += pm9g45.dtb
> >  # sam9n12
> >  dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb
> >  # sam9x5
> > diff --git a/arch/arm/boot/dts/pm9g45.dts b/arch/arm/boot/dts/pm9g45.dts
> > new file mode 100644
> > index 0000000..b0c258d
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/pm9g45.dts
> > @@ -0,0 +1,144 @@
> > +/*
> > + * pm9g45.dts - Device Tree file for Ronetix pm9g45 board
> > + *
> > + *  Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
> > + *
> > + * Licensed under GPLv2.
> > + */
> > +/dts-v1/;
> > +/include/ "at91sam9g45.dtsi"
> > +
> > +/ {
> > +	model = "Ronetix pm9g45";
> > +	compatible = "ronetix,pm9g45", "atmel,at91sam9g45", "atmel,at91sam9";
> > +
> > +	chosen {
> > +		bootargs = "console=ttyS0,115200";
> > +	};
> > +
> > +	memory {
> > +		reg = <0x70000000 0x8000000>;
> > +	};
> > +
> > +	clocks {
> > +		#address-cells = <1>;
> > +		#size-cells = <1>;
> > +		ranges;
> > +
> > +		main_clock: clock at 0 {
> > +			compatible = "atmel,osc", "fixed-clock";
> > +			clock-frequency = <12000000>;
> > +		};
> > +	};
> > +
> > +	ahb {
> > +		apb {
> > +			dbgu: serial at ffffee00 {
> > +				status = "okay";
> > +			};
> > +
> > +			pinctrl at fffff200 {
> > +
> > +				board {
> > +					pinctrl_board_nand: nand0-board {
> > +						atmel,pins =
> > +							<3 3 0x0 0x1	/* PD3 gpio RDY pin pull_up*/
> > +							 2 14 0x0 0x1>;	/* PC14 gpio enable pin pull_up */
> > +					};
> > +				};
> > +			};
> > +
> > +			macb0: ethernet at fffbc000 {
> > +				phy-mode = "rmii";
> > +				status = "okay";
> > +			};
> > +		};
> > +
> > +		nand0: nand at 40000000 {
> > +			nand-bus-width = <8>;
> > +			nand-ecc-mode = "soft";
> > +			nand-on-flash-bbt;
> > +			pinctrl-0 = <&pinctrl_board_nand>;
> > +
> > +			gpios = <&pioD 3 0
> > +				 &pioC 14 0
> > +				 0
> > +				>;
> > +
> > +			status = "okay";
> > +
> > +			at91bootstrap at 0 {
> > +				label = "at91bootstrap";
> > +				reg = <0x0 0x20000>;
> > +			};
> > +
> > +			barebox at 20000 {
> > +				label = "barebox";
> > +				reg = <0x20000 0x40000>;
> > +			};
> > +
> > +			bareboxenv at 60000 {
> > +				label = "bareboxenv";
> > +				reg = <0x60000 0x1A0000>;
> > +			};
> > +
> > +			kernel at 200000 {
> > +				label = "bareboxenv2";
> > +				reg = <0x200000 0x300000>;
> > +			};
> > +
> > +			kernel at 500000 {
> > +				label = "root";
> > +				reg = <0x500000 0x400000>;
> > +			};
> > +
> > +			data at 900000 {
> > +				label = "data";
> > +				reg = <0x900000 0x8340000>;
> > +			};
> > +		};
> > +
> > +		usb0: ohci at 00700000 {
> > +			status = "okay";
> > +			num-ports = <2>;
> > +		};
> > +
> > +		usb1: ehci at 00800000 {
> > +			status = "okay";
> > +		};
> > +	};
> > +
> > +	leds {
> > +		compatible = "gpio-leds";
> > +
> > +		led0 {
> > +			label = "led0";
> > +			gpios = <&pioD 0 1>;
> > +			linux,default-trigger = "nand-disk";
> > +		};
> > +
> > +		led1 {
> > +			label = "led1";
> > +			gpios = <&pioD 31 0>;
> > +			linux,default-trigger = "heartbeat";
> > +		};
> > +	};
> > +
> > +	gpio_keys {
> > +		compatible = "gpio-keys";
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +
> > +		right {
> > +			label = "SW4";
> > +			gpios = <&pioE 7 1>;
> > +			linux,code = <106>;
> > +		};
> > +
> > +		up {
> > +			label = "SW3";
> > +			gpios = <&pioE 8 1>;
> > +			linux,code = <103>;
> > +		};
> > +	};
> > +};
> > 
> 
> 
> -- 
> Nicolas Ferre



More information about the linux-arm-kernel mailing list