[PATCH] ARM: OMAP1: use BUG_ON where possible
Sasha Levin
sasha.levin at oracle.com
Thu Nov 8 15:23:09 EST 2012
Just use BUG_ON() instead of constructions such as:
if (...)
BUG()
A simplified version of the semantic patch that makes this transformation
is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
- if (e) BUG();
+ BUG_ON(e);
// </smpl>
Signed-off-by: Sasha Levin <sasha.levin at oracle.com>
---
arch/arm/mach-omap1/board-fsample.c | 3 +--
arch/arm/mach-omap1/board-h2.c | 3 +--
arch/arm/mach-omap1/board-h3.c | 3 +--
arch/arm/mach-omap1/board-perseus2.c | 3 +--
4 files changed, 4 insertions(+), 8 deletions(-)
diff --git a/arch/arm/mach-omap1/board-fsample.c b/arch/arm/mach-omap1/board-fsample.c
index 8b5800a..7ca6cc4 100644
--- a/arch/arm/mach-omap1/board-fsample.c
+++ b/arch/arm/mach-omap1/board-fsample.c
@@ -307,8 +307,7 @@ static void __init omap_fsample_init(void)
fsample_init_smc91x();
- if (gpio_request(FSAMPLE_NAND_RB_GPIO_PIN, "NAND ready") < 0)
- BUG();
+ BUG_ON(gpio_request(FSAMPLE_NAND_RB_GPIO_PIN, "NAND ready") < 0);
gpio_direction_input(FSAMPLE_NAND_RB_GPIO_PIN);
omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
diff --git a/arch/arm/mach-omap1/board-h2.c b/arch/arm/mach-omap1/board-h2.c
index 9134b64..4953cf7 100644
--- a/arch/arm/mach-omap1/board-h2.c
+++ b/arch/arm/mach-omap1/board-h2.c
@@ -412,8 +412,7 @@ static void __init h2_init(void)
h2_nand_resource.end = h2_nand_resource.start = OMAP_CS2B_PHYS;
h2_nand_resource.end += SZ_4K - 1;
- if (gpio_request(H2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
- BUG();
+ BUG_ON(gpio_request(H2_NAND_RB_GPIO_PIN, "NAND ready") < 0);
gpio_direction_input(H2_NAND_RB_GPIO_PIN);
omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
diff --git a/arch/arm/mach-omap1/board-h3.c b/arch/arm/mach-omap1/board-h3.c
index bf213d1..563ba16 100644
--- a/arch/arm/mach-omap1/board-h3.c
+++ b/arch/arm/mach-omap1/board-h3.c
@@ -406,8 +406,7 @@ static void __init h3_init(void)
nand_resource.end = nand_resource.start = OMAP_CS2B_PHYS;
nand_resource.end += SZ_4K - 1;
- if (gpio_request(H3_NAND_RB_GPIO_PIN, "NAND ready") < 0)
- BUG();
+ BUG_ON(gpio_request(H3_NAND_RB_GPIO_PIN, "NAND ready") < 0);
gpio_direction_input(H3_NAND_RB_GPIO_PIN);
/* GPIO10 Func_MUX_CTRL reg bit 29:27, Configure V2 to mode1 as GPIO */
diff --git a/arch/arm/mach-omap1/board-perseus2.c b/arch/arm/mach-omap1/board-perseus2.c
index 030bd48..67c2612 100644
--- a/arch/arm/mach-omap1/board-perseus2.c
+++ b/arch/arm/mach-omap1/board-perseus2.c
@@ -275,8 +275,7 @@ static void __init omap_perseus2_init(void)
perseus2_init_smc91x();
- if (gpio_request(P2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
- BUG();
+ BUG_ON(gpio_request(P2_NAND_RB_GPIO_PIN, "NAND ready") < 0);
gpio_direction_input(P2_NAND_RB_GPIO_PIN);
omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
--
1.7.10.4
More information about the linux-arm-kernel
mailing list