[PATCH 6/9] ARM: ux500: cosmetic fixups for uart0

[Linus Walleij]

From: Patrice Chotard <patrice.chotard at stericsson.com>

Changed a comment and ordered BIAS defines around a bit.

Signed-off-by: Patrice Chotard <patrice.chotard at stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
---
 arch/arm/mach-ux500/board-mop500-pins.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index 662563a..0009ca2 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -51,8 +51,6 @@ BIAS(slpm_in_wkup_pdis, PIN_SLEEPMODE_ENABLED|
 	PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
 BIAS(slpm_wkup_pdis, PIN_SLEEPMODE_ENABLED|
 	PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_out_wkup_pdis, PIN_SLEEPMODE_ENABLED|
-	PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
 BIAS(slpm_out_lo_pdis, PIN_SLEEPMODE_ENABLED|
 	PIN_SLPM_OUTPUT_LOW|PIN_SLPM_WAKEUP_DISABLE|PIN_SLPM_PDIS_DISABLED);
 BIAS(slpm_out_lo_wkup, PIN_SLEEPMODE_ENABLED|
@@ -65,6 +63,8 @@ BIAS(slpm_in_nopull_wkup_pdis, PIN_SLEEPMODE_ENABLED|
 	PIN_SLPM_INPUT_NOPULL|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
 BIAS(slpm_in_pu_wkup_pdis_en, PIN_SLEEPMODE_ENABLED|PIN_SLPM_INPUT_PULLUP|
 	PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_ENABLED);
+BIAS(slpm_out_wkup_pdis, PIN_SLEEPMODE_ENABLED|
+	PIN_SLPM_DIR_OUTPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
 BIAS(out_lo_wkup_pdis, PIN_SLPM_OUTPUT_LOW|
 	PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
 BIAS(in_wkup_pdis_en, PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|
@@ -156,7 +156,7 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
 	DB8500_PIN("GPIO1_AJ3", out_hi, "uart0"), /* RTS */
 	DB8500_PIN("GPIO2_AH4", in_pu, "uart0"), /* RXD */
 	DB8500_PIN("GPIO3_AH3", out_hi, "uart0"), /* TXD */
-	/* UART0 sleep state */
+	/* Sleep state for UART0 */
 	DB8500_PIN_SLEEP("GPIO0_AJ5", slpm_in_wkup_pdis, "uart0"),
 	DB8500_PIN_SLEEP("GPIO1_AJ3", slpm_out_hi_wkup_pdis, "uart0"),
 	DB8500_PIN_SLEEP("GPIO2_AH4", slpm_in_wkup_pdis, "uart0"),
-- 
1.7.11.3