[PATCH v3 4/4] ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND

[Murali Karicheri]

On 11/05/2012 08:29 AM, Philip, Avinash wrote:
> On Mon, Nov 05, 2012 at 18:28:22, Daniel Mack wrote:
>> On 05.11.2012 12:03, Philip, Avinash wrote:
>>> On Fri, Nov 02, 2012 at 20:55:56, Daniel Mack wrote:
>>>> This patch adds basic DT bindings for OMAP GPMC.
>>>>
>>>> The actual peripherals are instanciated from child nodes within the GPMC
>>>> node, and the only type of device that is currently supported is NAND.
>>>>
>>>> Code was added to parse the generic GPMC timing parameters and some
>>>> documentation with examples on how to use them.
>>>>
>>>> Successfully tested on an AM33xx board.
>>>>
>>>> Signed-off-by: Daniel Mack <zonque at gmail.com>
>>> [...]
>>>> +
>>>> +		nand at 0,0 {
>>>> +			reg = <0 0 0>; /* CS0, offset 0 */
>>>> +			nand-bus-width = <16>;
>>>> +			nand-ecc-mode = "none";
>>>> +
>>>> +			gpmc,sync-clk = <0>;
>>>> +			gpmc,cs-on = <0>;
>>>> +			gpmc,cs-rd-off = <36>;
>>>> +			gpmc,cs-wr-off = <36>;
>>>> +			gpmc,adv-on = <6>;
>>>> +			gpmc,adv-rd-off = <24>;
>>>> +			gpmc,adv-wr-off = <36>;
>>>> +			gpmc,we-off = <30>;
>>>> +			gpmc,oe-off = <48>;
>>>> +			gpmc,access = <54>;
>>>> +			gpmc,rd-cycle = <72>;
>>>> +			gpmc,wr-cycle = <72>;
>>>> +			gpmc,wr-access = <30>;
>>>> +			gpmc,wr-data-mux-bus = <0>;
>>>> +
>>>> +			#address-cells = <1>;
>>>> +			#size-cells = <1>;
>>>> +
>>> Can you take the timings (for example) from arago tree. The timings is tested in am335x-evm
>>> So the timings can be directly used to populate GPMC timings. Timings can found at
>>>
>>> http://arago-project.org/git/projects/?p=linux-am33x.git;a=commitdiff;
>>> h=66bfbd2c5b35dc81edce0c24843c476161ab5978;hp=370630359cb8db711cf0941cd2a242e28ccfb61e
>>>
>>> [...]
>>>> +static int gpmc_probe_dt(struct platform_device *pdev)
>>> Can you take care of the following section mismatch.
>>> WARNING: vmlinux.o(.text+0x1e2d0): Section mismatch in reference
>>> from the function gpmc_probe_dt() to the function .init.text:gpmc_nand_init().
>> Sore, both fixed for v4.
>>
>>> [...]
>>>> +
>>>> +		val = of_get_nand_ecc_mode(child);
>>>> +		if (val >= 0)
>>>> +			gpmc_nand_data->ecc_opt = val;
>>> This will fail for BCH. Index of "soft_bch" is 5 & also don't have selection
>>> option between for BCH4 & BCH8 also.
>>> Can you use the of_property_read_u32 (as done early) to pass the ecc selection
>>> from dt file. This will help selection of BCH4 & BCH8 ecc options.
>> Hmm. Shouldn't we rather teach of_get_nand_ecc_mode() that two modes and
>> bring the enum in sync?
> ecc_opt is for selecting different ecc layout and not for selecting ecc mode.
>
> In omap2 driver NAND_ECC_HW ecc mode supports 3 ecc layout
> 	OMAP_ECC_HAMMING_CODE_HW_ROMCODE
> 	OMAP_ECC_BCH4_CODE_HW
> 	OMAP_ECC_BCH8_CODE_HW
>
> So selection of ecc layout data should come from DT not ecc mode.
>
> Thanks
> Avinash
>
>>
>> Daniel
>>
>>
>>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
Hi,

I am working on an AEMIF driver for DaVinci that is similar to this. Is 
this a memory or mfd device?

Murali