usb, davinci: usb 2.0 problem on an am1808 based board

[Heiko Schocher]

Hello Manjunathappa,

Manjunathappa, Prakash wrote:
> Hi Heiko,
> 
> I do not know how putting delay helped MSC device detection.
> Can you please check if MUSB is coming up in "b_idle" state(by
> $cat /sys/devices/platform/musb-da8xx/musb-hdrc/mode)?
> State should move to b_peripheral on connecting gadget cable.

We have connected the USB0_ID pin to ground -> host only mode, so
I could not try this.

> If you connect MSC device via mini-A connector, state should change to "a_host".
> OTG timer is responsible for above state changes, can you please check if below
> changes are present?
> diff --git a/drivers/usb/musb/da8xx.c b/drivers/usb/musb/da8xx.c index 4da7492..a1a692e 100644
> --- a/drivers/usb/musb/da8xx.c
> +++ b/drivers/usb/musb/da8xx.c
> @@ -76,6 +76,7 @@
>  #define DA8XX_INTR_TX_SHIFT    0
>  #define DA8XX_INTR_TX_MASK     (DA8XX_USB_TX_EP_MASK << DA8XX_INTR_TX_SHIFT)
> 
> +#define A_WAIT_BCON_TIMEOUT     1100            /* in ms */
>  #define DA8XX_MENTOR_CORE_OFFSET 0x400
> 
>  #define CFGCHIP2       IO_ADDRESS(DA8XX_SYSCFG0_BASE + DA8XX_CFGCHIP2_REG)
> @@ -443,6 +444,7 @@ static int da8xx_musb_init(struct musb *musb)
>                  rev, __raw_readl(CFGCHIP2),
>                  musb_readb(reg_base, DA8XX_USB_CTRL_REG));
> 
> +       musb->a_wait_bcon = A_WAIT_BCON_TIMEOUT;
>         musb->isr = da8xx_musb_interrupt;
>         return 0;
>  fail:

No, this change is not in current mainline ...

Added this patch, and I get:

$ make -s uImage
drivers/usb/musb/da8xx.c: In function 'da8xx_musb_init':
drivers/usb/musb/da8xx.c:448:22: error: 'A_WAIT_BCON_TIMEOUT' undeclared (first use in this function)
drivers/usb/musb/da8xx.c:448:22: note: each undeclared identifier is reported only once for each function it appears in
make[3]: *** [drivers/usb/musb/da8xx.o] Error 1
make[2]: *** [drivers/usb/musb] Error 2
make[1]: *** [drivers/usb] Error 2
make: *** [drivers] Error 2
$

Do you mean

musb->a_wait_bcon = OTG_TIME_A_WAIT_BCON;

? This is setup in musb_core.c::allocate_instance() as Sergei Shtylyov
already commented ... nevertheless tried with this define your patch,
and my USB stick gets detected too...

bye,
Heiko
-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de