[PATCH 00/08] mach-shmobile: Emma Mobile EV2 support V3

[Simon Horman]

Hi Magnus,

On Fri, May 18, 2012 at 12:40:21PM +0900, Magnus Damm wrote:
> Hi Simon,
> 
> On Fri, May 18, 2012 at 10:44 AM, Simon Horman <horms at verge.net.au> wrote:
> > Hi Magnus,
> >
> > I have tested these patches on top of the soc-new branch of
> > rafael's renesas tree, revision 5658c94, which is based on
> > v3.4-rc6.
> 
> Excellent!
> 
> > I also have the cherry picked following patches before applying your patches.
> >
> > serial8250-em: clk_get() IS_ERR() error handling fix
> > serial8250-em: Emma Mobile UART driver V2
> > serial8250: Introduce serial8250_register_8250_port()
> > serial8250: Clean up default map and dl code
> > serial8250: Use dl_read()/dl_write() on RM9K
> > serial8250: Use dl_read()/dl_write() on Alchemy
> > serial8250: Add dl_read()/dl_write() callbacks
> > 8250.c: less than 2400 baud fix.
> > serial/8250_pci: Clear FIFOs for Intel ME Serial Over Lan device on BI
> > tegra, serial8250: add ->handle_break() uart_port op
> > clocksource: em_sti: Add DT support
> > clocksource: em_sti: Emma Mobile STI driver V2
> > clockevents: Make clockevents_config() a global symbol
> 
> Thanks, those are indeed needed for runtime UART and STI support, but
> there shouldn't be any build time dependencies.
> 
> > I have added the follwing patch of yours
> >
> > gpio: Emma Mobile GPIO driver V2
> >
> > And one of my own, which just fixes a build problem
> > in rafael's tree.
> >
> > ARM: mach-types: Manually add KZM-A9-GT
> 
> Right, that's a bit of a mess.
> 
> > On Wed, May 16, 2012 at 03:44:49PM +0900, Magnus Damm wrote:
> >> mach-shmobile: Emma Mobile EV2 support V3
> >>
> >> [PATCH 01/08] mach-shmobile: Emma Mobile EV2 SoC base support V3
> >
> > Tested-by: Simon Horman <horms at verge.net.au>
> >
> >> [PATCH 02/08] ARM: Undelete KZM9D mach-type V3
> >
> > I did not need this patch with the base I am using,
> > so I did not test it.
> 
> Ok!

:)

> > Reviewed-by: Simon Horman <horms at verge.net.au>
> >
> >> [PATCH 03/08] mach-shmobile: KZM9D board support V3
> >
> > Tested-by: Simon Horman <horms at verge.net.au>
> >
> >> [PATCH 04/08] mach-shmobile: Emma Mobile EV2 SMP support V3
> >
> > Tested-by: Simon Horman <horms at verge.net.au>
> >
> >> [PATCH 05/08] mach-shmobile: Emma Mobile EV2 GPIO support V3
> >
> > I am only seeing interripts for em_gio.0, is there a
> > way to exercise em_gio.1 .. 4 ?
> 
> When we start using other GPIO pins with interrupts then that will
> happen. Right now there is no code.

Ok, in that case

Tested-by: Simon Horman <horms at verge.net.au>

> > Duplicate names for interrupts, that is
> > each of em_gio.0..4 have two entries in /proc/interripts.
> > Is this intentional?
> 
> Yes, it is intentional. There are two interrupt sources per 32 GPIO pins.

In that case

Tested-by: Simon Horman <horms at verge.net.au>

> >> [PATCH 06/08] mach-shmobile: KZM9D board Ethernet support V3
> >
> > Tested-by: Simon Horman <horms at verge.net.au>
> >
> >> [PATCH 07/08] mach-shmobile: Emma Mobile EV2 DT support V3
> >
> > I applied this and the resulting kernel booted.
> 
> That's good! Thanks for testing!

Tested-by: Simon Horman <horms at verge.net.au>

> >> [PATCH 08/08] mach-shmobile: Use DT_MACHINE for KZM9D V3
> >
> > I applied this and the resulting kernel did not boot.
> > I saw nothing after the uboot prompt..
> 
> Yeah, you need to select CONFIG_ARM_APPENDED_DTB=y and append the DTB
> to the zImage, then convert that to uImage.

Thanks for working me through that off-line.

Tested-by: Simon Horman <horms at verge.net.au>

> 
> > Lastly, could you consider suppling a patch which provides a defconfig?
> 
> I've been asked to provide a defconfig that we can share between
> multiple platforms. So it's on my TODO.

Excellent