[PATCH v3] OMAP2+: UART: Add mechanism to probe uart pins and configure rx wakeup
Govindraj.R
govindraj.raja at ti.com
Fri May 11 05:40:42 EDT 2012
From: "Govindraj.R" <govindraj.raja at ti.com>
The commit (bce492c0 ARM: OMAP2+: UART: Fix incorrect population of
default uart pads) removed default uart pads that where getting populated
and which was making rx pin wakeup capable. If uart pads were used in
different mode by any other module then it would fail since the default
pads took over all the uart pins forcefully. With removal of default pads
the rx_pad wakeup for console uart while waking up from off mode is broken.
Utilise the mux api available to probe the availability of mux pins
in uart mode and probe for availability of uart pin in mux mode0
if uart is available as uart pin itself then configure rx pin
as wakeup capable.
This patch itself doesn't cater to all boards. Boards using uart rx wakeup
mechanism should ensure the usage of omap_serial_init_port by configuring
required uart ports and pass necessary mux data, till then this probing of
uart pins can cater to enabling of rx pad wakeup to most of the boards.
This patch can also throw some boot warning from _omap_mux_get_by_name
if pin is requested for availability is not present while dynamically probing
the uart pins availability such boot warnings can be addressed only when board
files are patched with omap_serial_init_port calls passing the right pads
needed for a given port.
Discussion Threads for reference:
http://www.spinics.net/lists/linux-omap/msg69859.html
http://www.spinics.net/lists/linux-omap/msg68659.html
Cc: Felipe Balbi <balbi at ti.com>
Cc: Kevin Hilman <khilman at ti.com>
Cc: Russ Dill <russ.dill at gmail.com>
Cc: Tony Lindgren <tony at atomide.com>
Cc: Paul Walmsley <paul at pwsan.com>
Cc: Ameya Palande <ameya.palande at ti.com>
Signed-off-by: Govindraj.R <govindraj.raja at ti.com>
---
Patching of all board files would be difficult as even I am not aware of all
omap-board schematics and uart port usage. So individual board file can be
enabled accordingly for uart usage by calling omap_serial_init_port call
with right mux data.
for testing: Patch based on v3.4-rc6
(tested on beagle-xm for off mode rx wakeup)
Patch targeted for v3.5
arch/arm/mach-omap2/mux.c | 3 +-
arch/arm/mach-omap2/mux.h | 11 +++++++
arch/arm/mach-omap2/serial.c | 65 +++++++++++++++++++++++++++++++++++++++--
3 files changed, 73 insertions(+), 6 deletions(-)
diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c
index 65c3391..d937ddd 100644
--- a/arch/arm/mach-omap2/mux.c
+++ b/arch/arm/mach-omap2/mux.c
@@ -217,8 +217,7 @@ static int __init _omap_mux_get_by_name(struct omap_mux_partition *partition,
return -ENODEV;
}
-static int __init
-omap_mux_get_by_name(const char *muxname,
+int __init omap_mux_get_by_name(const char *muxname,
struct omap_mux_partition **found_partition,
struct omap_mux **found_mux)
{
diff --git a/arch/arm/mach-omap2/mux.h b/arch/arm/mach-omap2/mux.h
index 69fe060..471e62a 100644
--- a/arch/arm/mach-omap2/mux.h
+++ b/arch/arm/mach-omap2/mux.h
@@ -59,6 +59,7 @@
#define OMAP_PIN_OFF_WAKEUPENABLE OMAP_WAKEUP_EN
#define OMAP_MODE_GPIO(x) (((x) & OMAP_MUX_MODE7) == OMAP_MUX_MODE4)
+#define OMAP_MODE_UART(x) (((x) & OMAP_MUX_MODE7) == OMAP_MUX_MODE0)
/* Flags for omapX_mux_init */
#define OMAP_PACKAGE_MASK 0xffff
@@ -225,8 +226,18 @@ omap_hwmod_mux_init(struct omap_device_pad *bpads, int nr_pads);
*/
void omap_hwmod_mux(struct omap_hwmod_mux_info *hmux, u8 state);
+int omap_mux_get_by_name(const char *muxname,
+ struct omap_mux_partition **found_partition,
+ struct omap_mux **found_mux);
#else
+static inline int omap_mux_get_by_name(const char *muxname,
+ struct omap_mux_partition **found_partition,
+ struct omap_mux **found_mux)
+{
+ return 0;
+}
+
static inline int omap_mux_init_gpio(int gpio, int val)
{
return 0;
diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index 9fc2f44..2dc50e7 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -57,6 +57,7 @@ struct omap_uart_state {
struct list_head node;
struct omap_hwmod *oh;
+ struct omap_device_pad default_omap_uart_pads[2];
};
static LIST_HEAD(uart_list);
@@ -126,11 +127,68 @@ static void omap_uart_set_smartidle(struct platform_device *pdev) {}
#endif /* CONFIG_PM */
#ifdef CONFIG_OMAP_MUX
-static void omap_serial_fill_default_pads(struct omap_board_data *bdata)
+
+#define OMAP_UART_DEFAULT_PAD_NAME_LEN 28
+static char rx_pad_name[OMAP_UART_DEFAULT_PAD_NAME_LEN],
+ tx_pad_name[OMAP_UART_DEFAULT_PAD_NAME_LEN] __initdata;
+
+static void __init
+omap_serial_fill_uart_tx_rx_pads(struct omap_board_data *bdata,
+ struct omap_uart_state *uart)
+{
+ uart->default_omap_uart_pads[0].name = rx_pad_name;
+ uart->default_omap_uart_pads[0].flags = OMAP_DEVICE_PAD_REMUX |
+ OMAP_DEVICE_PAD_WAKEUP;
+ uart->default_omap_uart_pads[0].enable = OMAP_PIN_INPUT |
+ OMAP_MUX_MODE0;
+ uart->default_omap_uart_pads[0].idle = OMAP_PIN_INPUT | OMAP_MUX_MODE0;
+ uart->default_omap_uart_pads[1].name = tx_pad_name;
+ uart->default_omap_uart_pads[1].enable = OMAP_PIN_OUTPUT |
+ OMAP_MUX_MODE0;
+ bdata->pads = uart->default_omap_uart_pads;
+ bdata->pads_cnt = ARRAY_SIZE(uart->default_omap_uart_pads);
+}
+
+static void __init omap_serial_check_wakeup(struct omap_board_data *bdata,
+ struct omap_uart_state *uart)
{
+ struct omap_mux_partition *tx_partition = NULL, *rx_partition = NULL;
+ struct omap_mux *rx_mux = NULL, *tx_mux = NULL;
+ char *rx_fmt, *tx_fmt;
+ int uart_nr = bdata->id + 1;
+
+ if (bdata->id != 2) {
+ rx_fmt = "uart%d_rx.uart%d_rx";
+ tx_fmt = "uart%d_tx.uart%d_tx";
+ } else {
+ rx_fmt = "uart%d_rx_irrx.uart%d_rx_irrx";
+ tx_fmt = "uart%d_tx_irtx.uart%d_tx_irtx";
+ }
+
+ snprintf(rx_pad_name, OMAP_UART_DEFAULT_PAD_NAME_LEN, rx_fmt,
+ uart_nr, uart_nr);
+ snprintf(tx_pad_name, OMAP_UART_DEFAULT_PAD_NAME_LEN, tx_fmt,
+ uart_nr, uart_nr);
+
+ if (omap_mux_get_by_name(rx_pad_name, &rx_partition, &rx_mux) >= 0 &&
+ omap_mux_get_by_name
+ (tx_pad_name, &tx_partition, &tx_mux) >= 0) {
+ u16 tx_mode, rx_mode;
+
+ tx_mode = omap_mux_read(tx_partition, tx_mux->reg_offset);
+ rx_mode = omap_mux_read(rx_partition, rx_mux->reg_offset);
+
+ /*
+ * Check if uart is used in default tx/rx mode i.e. in mux mode0
+ * if yes then configure rx pin for wake up capability
+ */
+ if (OMAP_MODE_UART(rx_mode) && OMAP_MODE_UART(tx_mode))
+ omap_serial_fill_uart_tx_rx_pads(bdata, uart);
+ }
}
#else
-static void omap_serial_fill_default_pads(struct omap_board_data *bdata) {}
+static void __init omap_serial_check_wakeup(struct omap_board_data *bdata
+ struct omap_uart_state *uart) {}
#endif
char *cmdline_find_option(char *str)
@@ -295,8 +353,7 @@ void __init omap_serial_board_init(struct omap_uart_port_info *info)
bdata.pads = NULL;
bdata.pads_cnt = 0;
- if (cpu_is_omap44xx() || cpu_is_omap34xx())
- omap_serial_fill_default_pads(&bdata);
+ omap_serial_check_wakeup(&bdata, uart);
if (!info)
omap_serial_init_port(&bdata, NULL);
--
1.7.9
More information about the linux-arm-kernel
mailing list