[PATCH 08/13] ARM: OMAP5: Add the WakeupGen IP updates.
Roger Quadros
rogerq at ti.com
Thu May 10 07:36:42 EDT 2012
Hi,
On 05/03/2012 10:26 AM, R Sricharan wrote:
> From: Santosh Shilimkar <santosh.shilimkar at ti.com>
>
> OMAP4 and OMAP5 share same WakeupGen IP with below few udpates on OMAP5.
> - Additional 32 interrupt support is added w.r.t OMAP4 design.
> - The AUX CORE boot registers are now made accessible from non-secure SW.
> - SAR offset are changed and PTMSYNC* registers are removed from SAR.
>
> Patch updates the WakeupGen code accordingly.
>
> Signed-off-by: Santosh Shilimkar <santosh.shilimkar at ti.com>
> Signed-off-by: R Sricharan <r.sricharan at ti.com>
> ---
> arch/arm/mach-omap2/include/mach/omap-wakeupgen.h | 6 +
> arch/arm/mach-omap2/omap-hotplug.c | 24 ++++-
> arch/arm/mach-omap2/omap-smp.c | 19 +++-
> arch/arm/mach-omap2/omap-wakeupgen.c | 110 +++++++++++++++-----
> arch/arm/mach-omap2/omap4-sar-layout.h | 12 ++-
> 5 files changed, 135 insertions(+), 36 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/include/mach/omap-wakeupgen.h b/arch/arm/mach-omap2/include/mach/omap-wakeupgen.h
> index 548de90..4d700bc 100644
> --- a/arch/arm/mach-omap2/include/mach/omap-wakeupgen.h
> +++ b/arch/arm/mach-omap2/include/mach/omap-wakeupgen.h
> @@ -11,15 +11,20 @@
> #ifndef OMAP_ARCH_WAKEUPGEN_H
> #define OMAP_ARCH_WAKEUPGEN_H
>
> +/* OMAP4 and OMAP5 has same base address */
> +#define OMAP_WKUPGEN_BASE 0x48281000
unnecessary change, why don't you just use OMAP44XX_WKUPGEN_BASE or
define this in the same header as OMAP44XX_WKUPGEN_BASE?
> +
> #define OMAP_WKG_CONTROL_0 0x00
> #define OMAP_WKG_ENB_A_0 0x10
> #define OMAP_WKG_ENB_B_0 0x14
> #define OMAP_WKG_ENB_C_0 0x18
> #define OMAP_WKG_ENB_D_0 0x1c
> +#define OMAP_WKG_ENB_E_0 0x20
> #define OMAP_WKG_ENB_A_1 0x410
> #define OMAP_WKG_ENB_B_1 0x414
> #define OMAP_WKG_ENB_C_1 0x418
> #define OMAP_WKG_ENB_D_1 0x41c
> +#define OMAP_WKG_ENB_E_1 0x420
> #define OMAP_AUX_CORE_BOOT_0 0x800
> #define OMAP_AUX_CORE_BOOT_1 0x804
> #define OMAP_PTMSYNCREQ_MASK 0xc00
> @@ -28,4 +33,5 @@
> #define OMAP_TIMESTAMPCYCLEHI 0xc0c
>
> extern int __init omap_wakeupgen_init(void);
> +extern void __iomem *omap_get_wakeupgen_base(void);
> #endif
> diff --git a/arch/arm/mach-omap2/omap-hotplug.c b/arch/arm/mach-omap2/omap-hotplug.c
> index 56c345b..052303c 100644
> --- a/arch/arm/mach-omap2/omap-hotplug.c
> +++ b/arch/arm/mach-omap2/omap-hotplug.c
> @@ -17,8 +17,10 @@
> #include <linux/kernel.h>
> #include <linux/errno.h>
> #include <linux/smp.h>
> +#include <linux/io.h>
>
> #include <asm/cacheflush.h>
> +#include <mach/omap-wakeupgen.h>
>
> #include "common.h"
>
> @@ -35,7 +37,8 @@ int platform_cpu_kill(unsigned int cpu)
> */
> void __ref platform_cpu_die(unsigned int cpu)
> {
> - unsigned int this_cpu;
> + unsigned int boot_cpu = 0;
> + void __iomem *base = omap_get_wakeupgen_base();
this is unnecessary copy for omap4, move it to the place where you want
it below.
+ void __iomem *base;
>
> flush_cache_all();
> dsb();
> @@ -43,16 +46,27 @@ void __ref platform_cpu_die(unsigned int cpu)
> /*
> * we're ready for shutdown now, so do it
> */
> - if (omap_modify_auxcoreboot0(0x0, 0x200) != 0x0)
> - pr_err("Secure clear status failed\n");
> + if (cpu_is_omap44xx()) {
> + if (omap_modify_auxcoreboot0(0x0, 0x200) != 0x0)
> + pr_err("Secure clear status failed\n");
> + } else {
i.e. here
+ *base = omap_get_wakeupgen_base();
> + __raw_writel(0, base + OMAP_AUX_CORE_BOOT_0);
> + }
> +
>
> for (;;) {
> /*
> * Enter into low power state
> */
> omap4_hotplug_cpu(cpu, PWRDM_POWER_OFF);
> - this_cpu = smp_processor_id();
> - if (omap_read_auxcoreboot0() == this_cpu) {
> +
> + if (cpu_is_omap44xx())
> + boot_cpu = omap_read_auxcoreboot0();
> + else
> + boot_cpu =
> + __raw_readl(base + OMAP_AUX_CORE_BOOT_0) >> 5;
> +
> + if (boot_cpu == smp_processor_id()) {
> /*
> * OK, proper wakeup, we're done
> */
> diff --git a/arch/arm/mach-omap2/omap-smp.c b/arch/arm/mach-omap2/omap-smp.c
> index deffbf1..151fd5b 100644
> --- a/arch/arm/mach-omap2/omap-smp.c
> +++ b/arch/arm/mach-omap2/omap-smp.c
> @@ -26,6 +26,8 @@
>
> #include <mach/hardware.h>
> #include <mach/omap-secure.h>
> +#include <mach/omap-wakeupgen.h>
> +#include <asm/cputype.h>
>
> #include "iomap.h"
> #include "common.h"
> @@ -73,6 +75,8 @@ int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
> {
> static struct clockdomain *cpu1_clkdm;
> static bool booted;
> + void __iomem *base = omap_get_wakeupgen_base();
ditto.
> +
> /*
> * Set synchronisation state between this boot processor
> * and the secondary one
> @@ -85,7 +89,11 @@ int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
> * the AuxCoreBoot1 register is updated with cpu state
> * A barrier is added to ensure that write buffer is drained
> */
> - omap_modify_auxcoreboot0(0x200, 0xfffffdff);
> + if (cpu_is_omap44xx())
> + omap_modify_auxcoreboot0(0x200, 0xfffffdff);
> + else
put it here instead
+{
+ void __iomem *base = omap_get_wakeup_base();
> + __raw_writel(0x20, base + OMAP_AUX_CORE_BOOT_0);
+}
> +
> flush_cache_all();
> smp_wmb();
>
> @@ -124,13 +132,20 @@ int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
>
> static void __init wakeup_secondary(void)
> {
> + void __iomem *base = omap_get_wakeupgen_base();
> +
ditto
> /*
> * Write the address of secondary startup routine into the
> * AuxCoreBoot1 where ROM code will jump and start executing
> * on secondary core once out of WFE
> * A barrier is added to ensure that write buffer is drained
> */
> - omap_auxcoreboot_addr(virt_to_phys(omap_secondary_startup));
> + if (cpu_is_omap44xx())
> + omap_auxcoreboot_addr(virt_to_phys(omap_secondary_startup));
> + else
> + __raw_writel(virt_to_phys(omap5_secondary_startup),
> + base + OMAP_AUX_CORE_BOOT_1);
> +
> smp_wmb();
>
> /*
> diff --git a/arch/arm/mach-omap2/omap-wakeupgen.c b/arch/arm/mach-omap2/omap-wakeupgen.c
> index 42cd7fb..444cf12 100644
> --- a/arch/arm/mach-omap2/omap-wakeupgen.c
> +++ b/arch/arm/mach-omap2/omap-wakeupgen.c
> @@ -33,18 +33,22 @@
> #include "omap4-sar-layout.h"
> #include "common.h"
>
> -#define NR_REG_BANKS 4
> -#define MAX_IRQS 128
> +#define MAX_NR_REG_BANKS 5
> +#define MAX_IRQS 160
> #define WKG_MASK_ALL 0x00000000
> #define WKG_UNMASK_ALL 0xffffffff
> #define CPU_ENA_OFFSET 0x400
> #define CPU0_ID 0x0
> #define CPU1_ID 0x1
> +#define OMAP4_NR_BANKS 4
> +#define OMAP4_NR_IRQS 128
>
> static void __iomem *wakeupgen_base;
> static void __iomem *sar_base;
> static DEFINE_SPINLOCK(wakeupgen_lock);
> static unsigned int irq_target_cpu[NR_IRQS];
> +static unsigned int irq_banks = MAX_NR_REG_BANKS;
> +static unsigned int max_irqs = MAX_IRQS;
>
> /*
> * Static helper functions.
> @@ -146,13 +150,13 @@ static void wakeupgen_unmask(struct irq_data *d)
> }
>
> #ifdef CONFIG_HOTPLUG_CPU
> -static DEFINE_PER_CPU(u32 [NR_REG_BANKS], irqmasks);
> +static DEFINE_PER_CPU(u32 [MAX_NR_REG_BANKS], irqmasks);
>
> static void _wakeupgen_save_masks(unsigned int cpu)
> {
> u8 i;
>
> - for (i = 0; i < NR_REG_BANKS; i++)
> + for (i = 0; i < irq_banks; i++)
> per_cpu(irqmasks, cpu)[i] = wakeupgen_readl(i, cpu);
> }
>
> @@ -160,7 +164,7 @@ static void _wakeupgen_restore_masks(unsigned int cpu)
> {
> u8 i;
>
> - for (i = 0; i < NR_REG_BANKS; i++)
> + for (i = 0; i < irq_banks; i++)
> wakeupgen_writel(per_cpu(irqmasks, cpu)[i], i, cpu);
> }
>
> @@ -168,7 +172,7 @@ static void _wakeupgen_set_all(unsigned int cpu, unsigned int reg)
> {
> u8 i;
>
> - for (i = 0; i < NR_REG_BANKS; i++)
> + for (i = 0; i < irq_banks; i++)
> wakeupgen_writel(reg, i, cpu);
> }
>
> @@ -196,25 +200,11 @@ static void wakeupgen_irqmask_all(unsigned int cpu, unsigned int set)
> #endif
>
> #ifdef CONFIG_CPU_PM
> -/*
> - * Save WakeupGen interrupt context in SAR BANK3. Restore is done by
> - * ROM code. WakeupGen IP is integrated along with GIC to manage the
> - * interrupt wakeups from CPU low power states. It manages
> - * masking/unmasking of Shared peripheral interrupts(SPI). So the
> - * interrupt enable/disable control should be in sync and consistent
> - * at WakeupGen and GIC so that interrupts are not lost.
> - */
> -static void irq_save_context(void)
> +static inline void omap4_irq_save_context(void)
> {
> u32 i, val;
>
> - if (omap_rev() == OMAP4430_REV_ES1_0)
> - return;
you removed the above check for 4430_ES1_0 here but do not add it back
in the new irq_save_context().
> -
> - if (!sar_base)
> - sar_base = omap4_get_sar_ram_base();
> -
> - for (i = 0; i < NR_REG_BANKS; i++) {
> + for (i = 0; i < irq_banks; i++) {
> /* Save the CPUx interrupt mask for IRQ 0 to 127 */
> val = wakeupgen_readl(i, 0);
> sar_writel(val, WAKEUPGENENB_OFFSET_CPU0, i);
> @@ -254,6 +244,53 @@ static void irq_save_context(void)
> val = __raw_readl(sar_base + SAR_BACKUP_STATUS_OFFSET);
> val |= SAR_BACKUP_STATUS_WAKEUPGEN;
> __raw_writel(val, sar_base + SAR_BACKUP_STATUS_OFFSET);
> +
> +}
> +
> +static inline void omap5_irq_save_context(void)
> +{
> + u32 i, val;
> +
> + for (i = 0; i < irq_banks; i++) {
> + /* Save the CPUx interrupt mask for IRQ 0 to 159 */
> + val = wakeupgen_readl(i, 0);
> + sar_writel(val, OMAP5_WAKEUPGENENB_OFFSET_CPU0, i);
> + val = wakeupgen_readl(i, 1);
> + sar_writel(val, OMAP5_WAKEUPGENENB_OFFSET_CPU1, i);
> + sar_writel(0x0, OMAP5_WAKEUPGENENB_SECURE_OFFSET_CPU0, i);
> + sar_writel(0x0, OMAP5_WAKEUPGENENB_SECURE_OFFSET_CPU1, i);
> + }
> +
> + /* Save AuxBoot* registers */
> + val = __raw_readl(wakeupgen_base + OMAP_AUX_CORE_BOOT_0);
> + __raw_writel(val, sar_base + OMAP5_AUXCOREBOOT0_OFFSET);
> + val = __raw_readl(wakeupgen_base + OMAP_AUX_CORE_BOOT_0);
> + __raw_writel(val, sar_base + OMAP5_AUXCOREBOOT1_OFFSET);
> +
> + /* Set the Backup Bit Mask status */
> + val = __raw_readl(sar_base + OMAP5_SAR_BACKUP_STATUS_OFFSET);
> + val |= SAR_BACKUP_STATUS_WAKEUPGEN;
> + __raw_writel(val, sar_base + OMAP5_SAR_BACKUP_STATUS_OFFSET);
> +
> +}
> +
> +/*
> + * Save WakeupGen interrupt context in SAR BANK3. Restore is done by
> + * ROM code. WakeupGen IP is integrated along with GIC to manage the
> + * interrupt wakeups from CPU low power states. It manages
> + * masking/unmasking of Shared peripheral interrupts(SPI). So the
> + * interrupt enable/disable control should be in sync and consistent
> + * at WakeupGen and GIC so that interrupts are not lost.
> + */
> +static void irq_save_context(void)
> +{
add the 4430 ES1 check here
+ if (omap_rev() == OMAP4430_REV_ES1_0)
+ return;
> + if (!sar_base)
> + sar_base = omap4_get_sar_ram_base();
> +
> + if (cpu_is_omap54xx())
> + omap5_irq_save_context();
> + else
> + omap4_irq_save_context();
> }
>
> /*
> @@ -262,9 +299,14 @@ static void irq_save_context(void)
> void irq_sar_clear(void)
> {
> u32 val;
> - val = __raw_readl(sar_base + SAR_BACKUP_STATUS_OFFSET);
> + u32 offset = SAR_BACKUP_STATUS_OFFSET;
> +
> + if (cpu_is_omap54xx())
> + offset = OMAP5_SAR_BACKUP_STATUS_OFFSET;
> +
> + val = __raw_readl(sar_base + offset);
> val &= ~SAR_BACKUP_STATUS_WAKEUPGEN;
> - __raw_writel(val, sar_base + SAR_BACKUP_STATUS_OFFSET);
> + __raw_writel(val, sar_base + offset);
> }
>
> /*
> @@ -336,13 +378,20 @@ static struct notifier_block irq_notifier_block = {
>
> static void __init irq_pm_init(void)
> {
> - cpu_pm_register_notifier(&irq_notifier_block);
> + /* FIXME: Remove this when MPU OSWR support is added */
> + if (!cpu_is_omap54xx())
> + cpu_pm_register_notifier(&irq_notifier_block);
> }
> #else
> static void __init irq_pm_init(void)
> {}
> #endif
>
> +void __iomem *omap_get_wakeupgen_base(void)
> +{
> + return wakeupgen_base;
> +}
> +
> /*
> * Initialise the wakeupgen module.
> */
> @@ -358,12 +407,17 @@ int __init omap_wakeupgen_init(void)
> }
>
> /* Static mapping, never released */
> - wakeupgen_base = ioremap(OMAP44XX_WKUPGEN_BASE, SZ_4K);
> + wakeupgen_base = ioremap(OMAP_WKUPGEN_BASE, SZ_4K);
unnecessary change. I don't see why you can't continue to use
OMAP44XX_WKUPGEN_BASE
> if (WARN_ON(!wakeupgen_base))
> return -ENOMEM;
>
> + if (cpu_is_omap44xx()) {
> + irq_banks = OMAP4_NR_BANKS;
> + max_irqs = OMAP4_NR_IRQS;
> + }
> +
> /* Clear all IRQ bitmasks at wakeupGen level */
> - for (i = 0; i < NR_REG_BANKS; i++) {
> + for (i = 0; i < irq_banks; i++) {
> wakeupgen_writel(0, i, CPU0_ID);
> wakeupgen_writel(0, i, CPU1_ID);
> }
> @@ -382,7 +436,7 @@ int __init omap_wakeupgen_init(void)
> */
>
> /* Associate all the IRQs to boot CPU like GIC init does. */
> - for (i = 0; i < NR_IRQS; i++)
> + for (i = 0; i < max_irqs; i++)
> irq_target_cpu[i] = boot_cpu;
>
> irq_hotplug_init();
> diff --git a/arch/arm/mach-omap2/omap4-sar-layout.h b/arch/arm/mach-omap2/omap4-sar-layout.h
> index fe5b545..e170fe8 100644
> --- a/arch/arm/mach-omap2/omap4-sar-layout.h
> +++ b/arch/arm/mach-omap2/omap4-sar-layout.h
> @@ -12,7 +12,7 @@
> #define OMAP_ARCH_OMAP4_SAR_LAYOUT_H
>
> /*
> - * SAR BANK offsets from base address OMAP44XX_SAR_RAM_BASE
> + * SAR BANK offsets from base address OMAP44XX/54XX_SAR_RAM_BASE
> */
> #define SAR_BANK1_OFFSET 0x0000
> #define SAR_BANK2_OFFSET 0x1000
> @@ -47,4 +47,14 @@
> #define PTMSYNCREQ_EN_OFFSET (SAR_BANK3_OFFSET + 0x6d0)
> #define SAR_BACKUP_STATUS_WAKEUPGEN 0x10
>
> +/* WakeUpGen save restore offset from OMAP54XX_SAR_RAM_BASE */
> +#define OMAP5_WAKEUPGENENB_OFFSET_CPU0 (SAR_BANK3_OFFSET + 0x8d4)
> +#define OMAP5_WAKEUPGENENB_SECURE_OFFSET_CPU0 (SAR_BANK3_OFFSET + 0x8e8)
> +#define OMAP5_WAKEUPGENENB_OFFSET_CPU1 (SAR_BANK3_OFFSET + 0x8fc)
> +#define OMAP5_WAKEUPGENENB_SECURE_OFFSET_CPU1 (SAR_BANK3_OFFSET + 0x910)
> +#define OMAP5_AUXCOREBOOT0_OFFSET (SAR_BANK3_OFFSET + 0x924)
> +#define OMAP5_AUXCOREBOOT1_OFFSET (SAR_BANK3_OFFSET + 0x928)
> +#define OMAP5_AMBA_IF_MODE_OFFSET (SAR_BANK3_OFFSET + 0x92c)
> +#define OMAP5_SAR_BACKUP_STATUS_OFFSET (SAR_BANK3_OFFSET + 0x800)
> +
> #endif
regards,
-roger
More information about the linux-arm-kernel
mailing list