[PATCH 3/7] mmc: dw_mmc: add device tree support
Kyungmin Park
kmpark at infradead.org
Wed May 2 02:55:52 EDT 2012
Hi,
On 5/2/12, Thomas Abraham <thomas.abraham at linaro.org> wrote:
> Add device tree based discovery support.
>
> Signed-off-by: Thomas Abraham <thomas.abraham at linaro.org>
> ---
> .../devicetree/bindings/mmc/synposis-dw-mshc.txt | 85 +++++++++
> drivers/mmc/host/dw_mmc-pltfm.c | 24 +++
> drivers/mmc/host/dw_mmc.c | 181
> +++++++++++++++++++-
> drivers/mmc/host/dw_mmc.h | 10 +
> include/linux/mmc/dw_mmc.h | 2 +
> 5 files changed, 296 insertions(+), 6 deletions(-)
> create mode 100644
> Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt
>
> diff --git a/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt
> b/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt
> new file mode 100644
> index 0000000..c1ed70e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt
> @@ -0,0 +1,85 @@
> +* Synopsis Designware Mobile Storage Host Controller
> +
> +The Synopsis designware mobile storage host controller is used to
> interface
> +a SoC with storage medium such as eMMC or SD/MMC cards.
> +
> +Required Properties:
> +
> +* compatible: should be one of the following
> + - synopsis,dw-mshc: for controllers compliant with synopsis dw-mshc.
I googled the "Synopsis Designware Mobile Storage Host Controller" and
Synopsis released it as this name. but still I like the 'dw-mmc'
instead of'dw-mshc'.
> +
> +* reg: physical base address of the dw-mshc controller and size of its
> memory
> + region.
> +
> +* interrupts: interrupt specifier for the controller. The format and value
> of
> + the interrupt specifier depends on the interrupt parent for the
> controller.
> +
> +# Slots: The slot specific information are contained within child-nodes
> with
> + each child-node representing a supported slot. There should be atleast
> one
> + child node representing a card slot. The name of the slot child node
> should
> + be 'slot{n}' where n is the unique number of the slot connnected to the
> + controller. The following are optional properties which can be included
> in
> + the slot child node.
> +
> + * bus-width: specifies the width of the data bus connected from the
> + controller to the card slot. The value should be 1, 4 or 8. In case
> + this property is not specified, a default value of 1 is assumed for
> + this property.
> +
> + * cd-gpios: specifies the card detect gpio line. The format of the
> + gpio specifier depends on the gpio controller.
> +
> + * wp-gpios: specifies the write protect gpio line. The format of the
> + gpio specifier depends on the gpio controller.
> +
> + * gpios: specifies a list of gpios used for command, clock and data
> + bus. The first gpio is the command line and the second gpio is the
> + clock line. The rest of the gpios (depending on the bus-width
> + property) are the data lines in no particular order. The format of
> + the gpio specifier depends on the gpio controller.
> +
> +Optional properties:
> +
> +* fifo-depth: The maximum size of the tx/rx fifo's. If this property is
> not
> + specified, the default value of the fifo size is determined from the
> + controller registers.
> +
> +* card-detect-delay: Delay in milli-seconds before detecting card after
> card
> + insert event. The default value is 0.
> +
> +* supports-highspeed: Enables support for high speed cards (upto 50MHz)
> +
> +* card-detection-broken: The card detection functionality is not available
> on
> + any of the slots.
> +
> +* no-write-protect: The write protect pad of the controller is not
> connected
> + to the write protect pin on the slot.
> +
> +Example:
> +
> + The MSHC controller node can be split into two portions, SoC specific
> and
> + board specific portions as listed below.
> +
> + dwmmc0 at 12200000 {
> + compatible = "synopsis,dw-mshc";
> + reg = <0x12200000 0x1000>;
> + interrupts = <0 75 0>;
> + };
> +
> + dwmmc0 at 12200000 {
> + supports-highspeed;
> + card-detection-broken;
> + no-write-protect;
> + fifo-depth = <0x80>;
> + card-detect-delay = <200>;
> +
> + slot0 {
> + bus-width = <8>;
> + cd-gpios = <&gpc0 2 2 3 3>;
> + gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>,
> + <&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>,
> + <&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>,
> + <&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>,
> + <&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>;
> + };
> + };
> diff --git a/drivers/mmc/host/dw_mmc-pltfm.c
> b/drivers/mmc/host/dw_mmc-pltfm.c
> index 92ec3eb..2b2c9bd 100644
> --- a/drivers/mmc/host/dw_mmc-pltfm.c
> +++ b/drivers/mmc/host/dw_mmc-pltfm.c
> @@ -19,8 +19,24 @@
> #include <linux/mmc/host.h>
> #include <linux/mmc/mmc.h>
> #include <linux/mmc/dw_mmc.h>
> +#include <linux/of.h>
> #include "dw_mmc.h"
>
> +#ifdef CONFIG_OF
> +static struct dw_mci_drv_data synopsis_drv_data = {
> + .ctrl_type = DW_MCI_TYPE_SYNOPSIS,
> +};
> +
> +static const struct of_device_id dw_mci_pltfm_match[] = {
> + { .compatible = "synopsis,dw-mshc",
> + .data = (void *)&synopsis_drv_data, },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, dw_mci_pltfm_match);
> +#else
> +static const struct of_device_id dw_mci_pltfm_match[];
> +#endif
> +
> static int dw_mci_pltfm_probe(struct platform_device *pdev)
> {
> struct dw_mci *host;
> @@ -51,6 +67,13 @@ static int dw_mci_pltfm_probe(struct platform_device
> *pdev)
> if (!host->regs)
> goto err_free;
> platform_set_drvdata(pdev, host);
> +
> + if (pdev->dev.of_node) {
> + const struct of_device_id *match;
> + match = of_match_node(dw_mci_pltfm_match, pdev->dev.of_node);
> + host->drv_data = match->data;
> + }
> +
> ret = dw_mci_probe(host);
> if (ret)
> goto err_out;
> @@ -111,6 +134,7 @@ static struct platform_driver dw_mci_pltfm_driver = {
> .remove = __exit_p(dw_mci_pltfm_remove),
> .driver = {
> .name = "dw_mmc",
> + .of_match_table = of_match_ptr(dw_mci_pltfm_match),
> .pm = &dw_mci_pltfm_pmops,
> },
> };
> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
> index 38cb7f8..bcf66d7 100644
> --- a/drivers/mmc/host/dw_mmc.c
> +++ b/drivers/mmc/host/dw_mmc.c
> @@ -33,9 +33,13 @@
> #include <linux/bitops.h>
> #include <linux/regulator/consumer.h>
> #include <linux/workqueue.h>
> +#include <linux/of.h>
> +#include <linux/of_gpio.h>
>
> #include "dw_mmc.h"
>
> +#define NUM_PINS(x) (x + 2)
> +
> /* Common flag combinations */
> #define DW_MCI_DATA_ERROR_FLAGS (SDMMC_INT_DTO | SDMMC_INT_DCRC | \
> SDMMC_INT_HTO | SDMMC_INT_SBE | \
> @@ -86,6 +90,8 @@ struct idmac_desc {
> struct dw_mci_slot {
> struct mmc_host *mmc;
> struct dw_mci *host;
> + int wp_gpio;
> + int cd_gpio;
>
> u32 ctype;
>
> @@ -816,6 +822,8 @@ static int dw_mci_get_ro(struct mmc_host *mmc)
> read_only = 0;
> else if (brd->get_ro)
> read_only = brd->get_ro(slot->id);
> + else if (gpio_is_valid(slot->wp_gpio))
> + read_only = gpio_get_value(slot->wp_gpio);
> else
> read_only =
> mci_readl(slot->host, WRTPRT) & (1 << slot->id) ? 1 : 0;
> @@ -837,6 +845,8 @@ static int dw_mci_get_cd(struct mmc_host *mmc)
> present = 1;
> else if (brd->get_cd)
> present = !brd->get_cd(slot->id);
> + else if (gpio_is_valid(slot->cd_gpio))
> + present = gpio_get_value(slot->cd_gpio);
> else
> present = (mci_readl(slot->host, CDETECT) & (1 << slot->id))
> == 0 ? 1 : 0;
> @@ -1747,6 +1757,96 @@ static void dw_mci_work_routine_card(struct
> work_struct *work)
> }
> }
>
> +#ifdef CONFIG_OF
> +static struct device_node *dw_mci_of_find_slot_node(struct device *dev, u8
> slot)
> +{
> + struct device_node *np;
> + char name[7];
> +
> + if (!dev || !dev->of_node)
> + return NULL;
> +
> + for_each_child_of_node(dev->of_node, np) {
> + sprintf(name, "slot%d", slot);
> + if (!strcmp(name, np->name))
> + return np;
> + }
> + return NULL;
> +}
> +
> +static u32 dw_mci_of_get_bus_wd(struct device *dev, u8 slot)
> +{
> + struct device_node *np = dw_mci_of_find_slot_node(dev, slot);
> + u32 bus_wd = 1;
> +
> + if (!np)
> + return 1;
> +
> + if (of_property_read_u32(np, "bus-width", &bus_wd))
> + dev_err(dev, "bus-width property not found, assuming width"
> + " as 1\n");
> + return bus_wd;
> +}
> +
> +static int dw_mci_of_setup_bus(struct dw_mci *host, u8 slot, u32 bus_wd)
> +{
> + struct device_node *np = dw_mci_of_find_slot_node(&host->dev, slot);
> + int idx, gpio, ret;
> +
> + for (idx = 0; idx < NUM_PINS(bus_wd); idx++) {
> + gpio = of_get_gpio(np, idx);
> + if (!gpio_is_valid(gpio)) {
> + dev_err(&host->dev, "invalid gpio: %d\n", gpio);
> + return -EINVAL;
> + }
> +
> + ret = devm_gpio_request(&host->dev, gpio, "dw-mci-bus");
> + if (ret) {
> + dev_err(&host->dev, "gpio [%d] request failed\n", gpio);
> + return -EBUSY;
> + }
> + }
> +
> + host->slot[slot]->wp_gpio = -1;
> + gpio = of_get_named_gpio(np, "wp_gpios", 0);
> + if (!gpio_is_valid(gpio)) {
> + dev_info(&host->dev, "wp gpio not available");
> + } else {
> + ret = devm_gpio_request(&host->dev, gpio, "dw-mci-wp");
> + if (ret)
> + dev_info(&host->dev, "gpio [%d] request failed\n",
> + gpio);
> + else
> + host->slot[slot]->wp_gpio = gpio;
> + }
> +
> + host->slot[slot]->cd_gpio = -1;
> + gpio = of_get_named_gpio(np, "cd-gpios", 0);
> + if (!gpio_is_valid(gpio)) {
> + dev_info(&host->dev, "cd gpio not available");
> + } else {
> + ret = devm_gpio_request(&host->dev, gpio, "dw-mci-cd");
> + if (ret)
> + dev_err(&host->dev, "gpio [%d] request failed\n", gpio);
> + else
> + host->slot[slot]->cd_gpio = gpio;
> + }
> +
> + return 0;
> +}
> +
> +#else /* CONFIG_OF */
> +static u32 dw_mci_of_get_bus_wd(struct device *dev, u8 slot)
> +{
> + return 1;
> +}
> +
> +static int dw_mci_of_setup_bus(struct dw_mci *host, u8 slot, u32 bus_wd)
> +{
> + return -EINVAL;
> +}
> +#endif /* CONFIG_OF */
> +
> static int __init dw_mci_init_slot(struct dw_mci *host, unsigned int id)
> {
> struct mmc_host *mmc;
> @@ -1760,6 +1860,7 @@ static int __init dw_mci_init_slot(struct dw_mci
> *host, unsigned int id)
> slot->id = id;
> slot->mmc = mmc;
> slot->host = host;
> + host->slot[id] = slot;
>
> mmc->ops = &dw_mci_ops;
> mmc->f_min = DIV_ROUND_UP(host->bus_hz, 510);
> @@ -1780,12 +1881,21 @@ static int __init dw_mci_init_slot(struct dw_mci
> *host, unsigned int id)
> if (host->pdata->caps)
> mmc->caps = host->pdata->caps;
>
> + mmc->caps |= host->drv_data->caps;
> +
> if (host->pdata->caps2)
> mmc->caps2 = host->pdata->caps2;
>
> - if (host->pdata->get_bus_wd)
> + if (host->pdata->get_bus_wd) {
> if (host->pdata->get_bus_wd(slot->id) >= 4)
> mmc->caps |= MMC_CAP_4_BIT_DATA;
> + } else if (host->dev.of_node) {
> + unsigned int bus_width;
> + bus_width = dw_mci_of_get_bus_wd(&host->dev, slot->id);
> + if (bus_width >= 4)
> + mmc->caps |= MMC_CAP_4_BIT_DATA;
In case of bus_width has 8; then how to handle it? maybe it's missing one.
> + dw_mci_of_setup_bus(host, slot->id, bus_width);
> + }
>
> if (host->pdata->quirks & DW_MCI_QUIRK_HIGHSPEED)
> mmc->caps |= MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED;
> @@ -1830,7 +1940,6 @@ static int __init dw_mci_init_slot(struct dw_mci
> *host, unsigned int id)
> else
> clear_bit(DW_MMC_CARD_PRESENT, &slot->flags);
>
> - host->slot[id] = slot;
> mmc_add_host(mmc);
>
> #if defined(CONFIG_DEBUG_FS)
> @@ -1923,15 +2032,75 @@ static bool mci_wait_reset(struct device *dev,
> struct dw_mci *host)
> return false;
> }
>
> +#ifdef CONFIG_OF
> +static struct dw_mci_of_quirks {
> + char *quirk;
> + int id;
> +} of_quriks[] = {
> + {
> + .quirk = "supports-highspeed",
> + .id = DW_MCI_QUIRK_HIGHSPEED,
> + }, {
> + .quirk = "card-detection-broken",
> + .id = DW_MCI_QUIRK_BROKEN_CARD_DETECTION,
> + }, {
> + .quirk = "no-write-protect",
> + .id = DW_MCI_QUIRK_NO_WRITE_PROTECT,
> + },
> + { }
> +};
> +
> +static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
> +{
> + struct dw_mci_board *pdata;
> + struct device *dev = &host->dev;
> + struct device_node *np = dev->of_node, *slot;
> + u32 timing[3];
> + int idx, cnt;
> +
> + pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
> + if (!pdata) {
> + dev_err(dev, "could not allocate memory for pdata\n");
> + return ERR_PTR(-ENOMEM);
> + }
> +
> + /* find out number of slots supported */
> + for_each_child_of_node(np, slot)
> + pdata->num_slots++;
> +
> + /* get quirks */
> + cnt = sizeof(of_quriks) / sizeof(struct dw_mci_of_quirks);
> + for (idx = 0; idx < cnt; idx++)
> + if (of_get_property(np, of_quriks[idx].quirk, NULL))
> + pdata->quirks |= of_quriks[idx].id;
> +
> + if (of_property_read_u32(np, "fifo-depth", &pdata->fifo_depth))
> + dev_info(dev, "fifo-depth property not found, using "
> + "value of FIFOTH register as default\n");
> +
> + of_property_read_u32(np, "card-detect-delay", &pdata->detect_delay_ms);
> +
> + return pdata;
> +}
> +
> +#else /* CONFIG_OF */
> +static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
> +{
> + return ERR_PTR(-EINVAL);
> +}
> +#endif /* CONFIG_OF */
> +
> int dw_mci_probe(struct dw_mci *host)
> {
> int width, i, ret = 0;
> u32 fifo_size;
>
> - if (!host->pdata || !host->pdata->init) {
> - dev_err(&host->dev,
> - "Platform data must supply init function\n");
> - return -ENODEV;
> + if (!host->pdata) {
> + host->pdata = dw_mci_parse_dt(host);
> + if (IS_ERR(host->pdata)) {
> + dev_err(&host->dev, "platform data not available\n");
> + return -EINVAL;
> + }
> }
>
> if (!host->pdata->select_slot && host->pdata->num_slots > 1) {
> diff --git a/drivers/mmc/host/dw_mmc.h b/drivers/mmc/host/dw_mmc.h
> index 15c27e1..8b8862b 100644
> --- a/drivers/mmc/host/dw_mmc.h
> +++ b/drivers/mmc/host/dw_mmc.h
> @@ -182,4 +182,14 @@ extern int dw_mci_suspend(struct dw_mci *host);
> extern int dw_mci_resume(struct dw_mci *host);
> #endif
>
> +/* Variations in the dw_mci controller */
> +#define DW_MCI_TYPE_SYNOPSIS 0
> +#define DW_MCI_TYPE_EXYNOS5250 1 /* Samsung Exynos5250 Extensions */
Um. it's not good idea to add specific SOC version. And as you know,
exynos4 series has this controller.
> +
> +/* dw_mci platform driver data */
> +struct dw_mci_drv_data {
> + unsigned long ctrl_type;
> + unsigned long caps;
> +};
> +
> #endif /* _DW_MMC_H_ */
> diff --git a/include/linux/mmc/dw_mmc.h b/include/linux/mmc/dw_mmc.h
> index fb51a5f..71d2b56 100644
> --- a/include/linux/mmc/dw_mmc.h
> +++ b/include/linux/mmc/dw_mmc.h
> @@ -78,6 +78,7 @@ struct mmc_data;
> * @data_offset: Set the offset of DATA register according to VERID.
> * @dev: Device associated with the MMC controller.
> * @pdata: Platform data associated with the MMC controller.
> + * @drv_data: Driver specific data for identified variant of the
> controller
> * @biu_clk: Pointer to bus interface unit clock instance.
> * @ciu_clk: Pointer to card interface unit clock instance.
> * @slot: Slots sharing this MMC controller.
> @@ -160,6 +161,7 @@ struct dw_mci {
> u16 data_offset;
> struct device dev;
> struct dw_mci_board *pdata;
> + struct dw_mci_drv_data *drv_data;
> struct clk *biu_clk;
> struct clk *ciu_clk;
> struct dw_mci_slot *slot[MAX_MCI_SLOTS];
> --
> 1.7.5.4
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
More information about the linux-arm-kernel
mailing list