[PATCH] ARM: at91: add support for Telit GE863-PRO3 Evaluation Kit
Fabio Porcedda
fabio.porcedda at gmail.com
Fri Mar 30 04:56:56 EDT 2012
Based on board-sam9260ek.c.
Signed-off-by: Fabio Porcedda <fabio.porcedda at gmail.com>
---
arch/arm/mach-at91/Kconfig | 6 +
arch/arm/mach-at91/Makefile | 1 +
arch/arm/mach-at91/board-ge863-pro3.c | 338 +++++++++++++++++++++++++++++++++
3 files changed, 345 insertions(+)
create mode 100644 arch/arm/mach-at91/board-ge863-pro3.c
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 45db05d..4197a2a 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -272,6 +272,12 @@ config MACH_FLEXIBITY
Select this if you are using Flexibity Connect board
<http://www.flexibity.com>
+config MACH_GE863_PRO3_EVK
+ bool "Telit GE863-PRO3 Evaluation Kit"
+ help
+ Select this if you are using Telit GE863-PRO3 Evaluation Kit
+ <http://www.telit.com>
+
endif
# ----------------------------------------------------------
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 8512e53..5ca096d 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -49,6 +49,7 @@ obj-$(CONFIG_MACH_QIL_A9260) += board-qil-a9260.o
obj-$(CONFIG_MACH_AFEB9260) += board-afeb-9260v1.o
obj-$(CONFIG_MACH_CPU9260) += board-cpu9krea.o
obj-$(CONFIG_MACH_FLEXIBITY) += board-flexibity.o
+obj-$(CONFIG_MACH_GE863_PRO3_EVK) += board-ge863-pro3.o
# AT91SAM9261 board-specific support
obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o
diff --git a/arch/arm/mach-at91/board-ge863-pro3.c b/arch/arm/mach-at91/board-ge863-pro3.c
new file mode 100644
index 0000000..2855cc0
--- /dev/null
+++ b/arch/arm/mach-at91/board-ge863-pro3.c
@@ -0,0 +1,338 @@
+/*
+ * linux/arch/arm/mach-at91/board-ge863-pro3-evk.c
+ *
+ * Copyright (C) 2012 Telit
+ *
+ * linux/arch/arm/mach-at91/board-sam9260ek.c
+ *
+ * Copyright (C) 2005 SAN People
+ * Copyright (C) 2006 Atmel
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/types.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/at73c213.h>
+#include <linux/clk.h>
+#include <linux/i2c/at24.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/board.h>
+#include <mach/at91sam9_smc.h>
+#include <mach/at91_shdwc.h>
+#include <mach/system_rev.h>
+
+#include "sam9_smc.h"
+#include "generic.h"
+
+
+static void __init ek_init_early(void)
+{
+ /* Initialize processor: 6.000 MHz crystal */
+ at91_initialize(6000000);
+
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS
+ | ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR
+ | ATMEL_UART_DCD | ATMEL_UART_RI);
+
+ /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS
+ | ATMEL_UART_RTS);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
+}
+
+/* USB Host port */
+static struct at91_usbh_data __initdata ek_usbh_data = {
+ .ports = 2,
+ .vbus_pin = {-EINVAL, -EINVAL},
+ .overcurrent_pin = {-EINVAL, -EINVAL},
+};
+
+/* USB Device port */
+static struct at91_udc_data __initdata ek_udc_data = {
+ .vbus_pin = AT91_PIN_PC5,
+ .pullup_pin = -EINVAL, /* pull-up driven by UDC */
+};
+
+
+/* Audio */
+static struct at73c213_board_info at73c213_data = {
+ .ssc_id = 0,
+ .shortname = "AT91SAM9260-EK external DAC",
+};
+
+#if defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE)
+static void __init at73c213_set_clk(struct at73c213_board_info *info)
+{
+ struct clk *pck0;
+ struct clk *plla;
+
+ pck0 = clk_get(NULL, "pck0");
+ plla = clk_get(NULL, "plla");
+
+ /* AT73C213 MCK Clock */
+ at91_set_B_periph(AT91_PIN_PC1, 0); /* PCK0 */
+
+ clk_set_parent(pck0, plla);
+ clk_put(plla);
+
+ info->dac_clk = pck0;
+}
+#else
+static void __init at73c213_set_clk(struct at73c213_board_info *info) {}
+#endif
+
+/* SPI devices. */
+static struct spi_board_info ek_spi_devices[] = {
+#if !defined(CONFIG_MMC_AT91)
+ { /* DataFlash chip */
+ .modalias = "mtd_dataflash",
+ .chip_select = 1,
+ .max_speed_hz = 15 * 1000 * 1000,
+ .bus_num = 0,
+ },
+#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
+ { /* DataFlash card */
+ .modalias = "mtd_dataflash",
+ .chip_select = 0,
+ .max_speed_hz = 15 * 1000 * 1000,
+ .bus_num = 0,
+ },
+#endif
+#endif
+#if defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE)
+ { /* AT73C213 DAC */
+ .modalias = "at73c213",
+ .chip_select = 0,
+ .max_speed_hz = 10 * 1000 * 1000,
+ .bus_num = 1,
+ .mode = SPI_MODE_1,
+ .platform_data = &at73c213_data,
+ },
+#endif
+};
+
+
+/* MACB Ethernet device */
+static struct macb_platform_data __initdata ek_macb_data = {
+ .phy_irq_pin = AT91_PIN_PA7,
+ .is_rmii = 1,
+};
+
+
+/* NAND flash */
+static struct mtd_partition __initdata ek_nand_partition[] = {
+ {
+ .name = "Partition 1",
+ .offset = 0,
+ .size = SZ_256K,
+ },
+ {
+ .name = "Partition 2",
+ .offset = MTDPART_OFS_NXTBLK,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct atmel_nand_data __initdata ek_nand_data = {
+ .ale = 21,
+ .cle = 22,
+ .det_pin = -EINVAL,
+ .rdy_pin = AT91_PIN_PC13,
+ .enable_pin = AT91_PIN_PC14,
+ .parts = ek_nand_partition,
+ .num_parts = ARRAY_SIZE(ek_nand_partition),
+};
+
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+ .ncs_read_setup = 0,
+ .nrd_setup = 1,
+ .ncs_write_setup = 0,
+ .nwe_setup = 1,
+
+ .ncs_read_pulse = 3,
+ .nrd_pulse = 3,
+ .ncs_write_pulse = 3,
+ .nwe_pulse = 3,
+
+ .read_cycle = 5,
+ .write_cycle = 5,
+
+ .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE
+ | AT91_SMC_EXNWMODE_DISABLE,
+ .tdf_cycles = 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+ ek_nand_data.bus_width_16 = board_have_nand_16bit();
+ /* setup bus-width (8 or 16) */
+ if (ek_nand_data.bus_width_16)
+ ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+ else
+ ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+ /* configure chip-select 3 (NAND) */
+ sam9_smc_configure(0, 3, &ek_nand_smc_config);
+
+ at91_add_device_nand(&ek_nand_data);
+}
+
+
+/* MCI (SD/MMC) */
+static struct at91_mmc_data __initdata ek_mmc_data = {
+ .slot_b = 1,
+ .wire4 = 1,
+ .det_pin = -EINVAL,
+ .wp_pin = -EINVAL,
+ .vcc_pin = -EINVAL,
+};
+
+
+/* LEDs */
+static struct gpio_led ek_leds[] = {
+ { /* "bottom" led, green, userled1 to be defined */
+ .name = "ds5",
+ .gpio = AT91_PIN_PA6,
+ .active_low = 1,
+ .default_trigger = "none",
+ },
+ { /* "power" led, yellow */
+ .name = "ds1",
+ .gpio = AT91_PIN_PA9,
+ .default_trigger = "heartbeat",
+ }
+};
+
+/* I2C devices */
+static struct at24_platform_data at24c512 = {
+ .byte_len = SZ_512K / 8,
+ .page_size = 128,
+ .flags = AT24_FLAG_ADDR16,
+};
+
+static struct i2c_board_info __initdata ek_i2c_devices[] = {
+ {
+ I2C_BOARD_INFO("24c512", 0x50),
+ .platform_data = &at24c512,
+ },
+ /* more devices can be added using expansion connectors */
+};
+
+
+/* GPIO Buttons */
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+static struct gpio_keys_button ek_buttons[] = {
+ {
+ .gpio = AT91_PIN_PA30,
+ .code = BTN_3,
+ .desc = "Button 3",
+ .active_low = 1,
+ .wakeup = 1,
+ },
+ {
+ .gpio = AT91_PIN_PA31,
+ .code = BTN_4,
+ .desc = "Button 4",
+ .active_low = 1,
+ .wakeup = 1,
+ }
+};
+
+static struct gpio_keys_platform_data ek_button_data = {
+ .buttons = ek_buttons,
+ .nbuttons = ARRAY_SIZE(ek_buttons),
+};
+
+static struct platform_device ek_button_device = {
+ .name = "gpio-keys",
+ .id = -1,
+ .num_resources = 0,
+ .dev = {
+ .platform_data = &ek_button_data,
+ }
+};
+
+static void __init ek_add_device_buttons(void)
+{
+ at91_set_gpio_input(AT91_PIN_PA30, 1); /* btn3 */
+ at91_set_deglitch(AT91_PIN_PA30, 1);
+ at91_set_gpio_input(AT91_PIN_PA31, 1); /* btn4 */
+ at91_set_deglitch(AT91_PIN_PA31, 1);
+
+ platform_device_register(&ek_button_device);
+}
+#else
+static void __init ek_add_device_buttons(void) {}
+#endif
+
+
+static void __init ek_board_init(void)
+{
+ /* Serial */
+ at91_add_device_serial();
+ /* USB Host */
+ at91_add_device_usbh(&ek_usbh_data);
+ /* USB Device */
+ at91_add_device_udc(&ek_udc_data);
+ /* SPI */
+ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+ /* NAND */
+ ek_add_device_nand();
+ /* Ethernet */
+ at91_add_device_eth(&ek_macb_data);
+ /* MMC */
+ at91_add_device_mmc(0, &ek_mmc_data);
+ /* I2C */
+ at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
+ /* SSC (to AT73C213) */
+ at73c213_set_clk(&at73c213_data);
+ at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
+ /* LEDs */
+ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
+ /* Push Buttons */
+ ek_add_device_buttons();
+}
+
+MACHINE_START(GE863, "Telit GE863-PRO3 Evaluation Kit")
+ /* Maintainer: Telit */
+ .timer = &at91sam926x_timer,
+ .map_io = at91_map_io,
+ .init_early = ek_init_early,
+ .init_irq = at91_init_irq_default,
+ .init_machine = ek_board_init,
+MACHINE_END
--
1.7.9.4
More information about the linux-arm-kernel
mailing list