[PATCH v3 2/4] video: s3c-fb: remove 'default_win' element from platform data

[Thomas Abraham]

The decision to enable or disable the data output to the lcd panel from
the controller need not be based on the value of 'default_win' element
in the platform data. Instead, the data output to the panel is enabled
if any of the windows are active, else data output is disabled.

Cc: Ben Dooks <ben-linux at fluff.org>
Signed-off-by: Jingoo Han <jg1.han at samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham at linaro.org>
---
 arch/arm/plat-samsung/include/plat/fb.h |    2 --
 drivers/video/s3c-fb.c                  |   25 +++++--------------------
 2 files changed, 5 insertions(+), 22 deletions(-)

diff --git a/arch/arm/plat-samsung/include/plat/fb.h b/arch/arm/plat-samsung/include/plat/fb.h
index 39d6bd7..536002f 100644
--- a/arch/arm/plat-samsung/include/plat/fb.h
+++ b/arch/arm/plat-samsung/include/plat/fb.h
@@ -62,8 +62,6 @@ struct s3c_fb_platdata {
 	struct s3c_fb_pd_win	*win[S3C_FB_MAX_WIN];
 	struct fb_videomode     *vtiming;
 
-	u32			 default_win;
-
 	u32			 vidcon0;
 	u32			 vidcon1;
 };
diff --git a/drivers/video/s3c-fb.c b/drivers/video/s3c-fb.c
index c94f40d..18c84b8 100644
--- a/drivers/video/s3c-fb.c
+++ b/drivers/video/s3c-fb.c
@@ -531,7 +531,7 @@ static int s3c_fb_set_par(struct fb_info *info)
 	/* disable the window whilst we update it */
 	writel(0, regs + WINCON(win_no));
 
-	if (win_no == sfb->pdata->default_win)
+	if (!sfb->output_on)
 		s3c_fb_enable(sfb, 1);
 
 	/* write the buffer address */
@@ -799,6 +799,7 @@ static int s3c_fb_blank(int blank_mode, struct fb_info *info)
 	struct s3c_fb *sfb = win->parent;
 	unsigned int index = win->index;
 	u32 wincon;
+	u32 output_on = sfb->output_on;
 
 	dev_dbg(sfb->dev, "blank mode %d\n", blank_mode);
 
@@ -837,34 +838,18 @@ static int s3c_fb_blank(int blank_mode, struct fb_info *info)
 
 	shadow_protect_win(win, 1);
 	writel(wincon, sfb->regs + sfb->variant.wincon + (index * 4));
-	shadow_protect_win(win, 0);
 
 	/* Check the enabled state to see if we need to be running the
 	 * main LCD interface, as if there are no active windows then
 	 * it is highly likely that we also do not need to output
 	 * anything.
 	 */
-
-	/* We could do something like the following code, but the current
-	 * system of using framebuffer events means that we cannot make
-	 * the distinction between just window 0 being inactive and all
-	 * the windows being down.
-	 *
-	 * s3c_fb_enable(sfb, sfb->enabled ? 1 : 0);
-	*/
-
-	/* we're stuck with this until we can do something about overriding
-	 * the power control using the blanking event for a single fb.
-	 */
-	if (index == sfb->pdata->default_win) {
-		shadow_protect_win(win, 1);
-		s3c_fb_enable(sfb, blank_mode != FB_BLANK_POWERDOWN ? 1 : 0);
-		shadow_protect_win(win, 0);
-	}
+	s3c_fb_enable(sfb, sfb->enabled ? 1 : 0);
+	shadow_protect_win(win, 0);
 
 	pm_runtime_put_sync(sfb->dev);
 
-	return 0;
+	return output_on == sfb->output_on;
 }
 
 /**
-- 
1.6.6.rc2