[PATCH v2] ARM: SPEAr600: Add device-tree support to SPEAr600 boards
Stefan Roese
sr at denx.de
Wed Mar 14 12:49:05 EDT 2012
On Wednesday 14 March 2012 17:21:52 Jean-Christophe PLAGNIOL-VILLARD wrote:
> On 16:00 Wed 14 Mar , Stefan Roese wrote:
> > This patch adds a generic target for SPEAr600 board that can be
> > configured via the device-tree. Currently the following devices
> > are supported via the devicetree:
> >
> > - VIC interrupts
> > - PL011 UART
> > - PL061 GPIO
> > - Synopsys DW I2C
> > - Synopsys DW ethernet
> >
> > Other peripheral devices (e.g. SMI flash, FSMC NAND flash etc) will
> > follow in later patches.
> >
> > Only the spear600-evb is currently supported. Other SPEAr600
> > based boards will follow later.
> >
> > Additionally the file spear600.c is deleted. It contained only
> > one empty function and is not needed. So lets just remove it.
> >
> > Signed-off-by: Stefan Roese <sr at denx.de>
> > Cc: Viresh Kumar <viresh.kumar at st.com>
> > Cc: Arnd Bergmann <arnd at arndb.de>
> > ---
> > v2:
> > - Added DT support to spear6xx.c instead of creating board-dt.c
> > - Removed UART (PL011) and GPIO (PL061) platform data for
> >
> > devicetree board port. This works now via DT probing
> >
> > - Added OF_DEV_AUXDATA for clock device name matching for some
> >
> > device drivers
> >
> > - Removed sper600.c file completely
> > - Added DW I2C and ethernet nodes to the dts files
> > - Added other DT nodes (SMI, FSMC, ECHI, OHCI), currently disabled
> >
> > since the corresponding device drivers don't support DT probing
> >
> > - Removed Linaro/FSL copyright notice from SPEAr DT files (copy-paste
> > cruft) - Many smaller modification to the dts/dtsi files
> > - Changed Documentation/devicetree/bindings/arm/spear.txt to match
> >
> > the changed bindings
> >
> > Documentation/devicetree/bindings/arm/spear.txt | 8 ++
> > arch/arm/boot/dts/spear600-evb.dts | 30 +++++
> > arch/arm/boot/dts/spear600.dtsi | 162
> > +++++++++++++++++++++++ arch/arm/mach-spear6xx/Kconfig
> > | 7 +
> > arch/arm/mach-spear6xx/Makefile | 3 -
> > arch/arm/mach-spear6xx/spear600.c | 25 ----
> > arch/arm/mach-spear6xx/spear600_evb.c | 3 -
> > arch/arm/mach-spear6xx/spear6xx.c | 69 +++++++++-
> > 8 files changed, 270 insertions(+), 37 deletions(-)
> > create mode 100644 Documentation/devicetree/bindings/arm/spear.txt
> > create mode 100644 arch/arm/boot/dts/spear600-evb.dts
> > create mode 100644 arch/arm/boot/dts/spear600.dtsi
> > delete mode 100644 arch/arm/mach-spear6xx/spear600.c
> >
> > diff --git a/Documentation/devicetree/bindings/arm/spear.txt
> > b/Documentation/devicetree/bindings/arm/spear.txt new file mode 100644
> > index 0000000..f8e54f0
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/arm/spear.txt
> > @@ -0,0 +1,8 @@
> > +ST SPEAr Platforms Device Tree Bindings
> > +---------------------------------------
> > +
> > +Boards with the ST SPEAr600 SoC shall have the following properties:
> > +
> > +Required root node property:
> > +
> > +compatible = "st,spear600";
> > diff --git a/arch/arm/boot/dts/spear600-evb.dts
> > b/arch/arm/boot/dts/spear600-evb.dts new file mode 100644
> > index 0000000..cbfda8d
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/spear600-evb.dts
> > @@ -0,0 +1,30 @@
> > +/*
> > + * Copyright 2012 Stefan Roese <sr at denx.de>
> > + *
> > + * The code contained herein is licensed under the GNU General Public
> > + * License. You may obtain a copy of the GNU General Public License
> > + * Version 2 or later at the following locations:
> > + *
> > + * http://www.opensource.org/licenses/gpl-license.html
> > + * http://www.gnu.org/copyleft/gpl.html
> > + */
> > +
> > +/dts-v1/;
> > +/include/ "spear600.dtsi"
> > +
> > +/ {
> > + model = "ST SPEAr600 Evaluation Board";
> > + compatible = "st,spear600-evb", "st,spear600";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
>
> please put the mem size here
Might I ask why? Other *.dtsi files don't have it either.
> > +
> > + soc {
> > + gmac0: ethernet at e0800000 {
> > + phy-mode = "gmii";
> > + };
> > +
> > + i2c at d0200000 {
> > + clock-frequency = <400000>;
> > + };
> > + };
> > +};
> > diff --git a/arch/arm/boot/dts/spear600.dtsi
> > b/arch/arm/boot/dts/spear600.dtsi new file mode 100644
> > index 0000000..e45e58f
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/spear600.dtsi
> > @@ -0,0 +1,162 @@
> > +/*
> > + * Copyright 2012 Stefan Roese <sr at denx.de>
> > + *
> > + * The code contained herein is licensed under the GNU General Public
> > + * License. You may obtain a copy of the GNU General Public License
> > + * Version 2 or later at the following locations:
> > + *
> > + * http://www.opensource.org/licenses/gpl-license.html
> > + * http://www.gnu.org/copyleft/gpl.html
> > + */
> > +
> > +/include/ "skeleton.dtsi"
> > +
> > +/ {
> > + compatible = "st,spear600";
> > +
> > + cpus {
> > + cpu at 0 {
> > + compatible = "arm,arm926ejs";
> > + };
> > + };
> > +
> > + memory {
> > + device_type = "memory";
> > + reg = <0 0>; /* Filled by U-Boot */
>
> please put the max mem of the SoC here
Why? It's always updated by the bootloader. And a max. mem size (when not
updated to the correct mem size by the bootloader) would crash the board if it
is equipped with less memory.
> > + };
> > +
> > + soc {
>
> please put the name of the bus not soc
Okay.
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + compatible = "simple-bus";
> > + ranges;
> > +
> > + vic0: interrupt-controller at f1100000 {
> > + compatible = "arm,pl190-vic";
> > + interrupt-controller;
> > + reg = <0xf1100000 0x1000>;
> > + #interrupt-cells = <1>;
> > + };
> > +
> > + vic1: interrupt-controller at f1000000 {
> > + compatible = "arm,pl190-vic";
> > + interrupt-controller;
> > + reg = <0xf1000000 0x1000>;
> > + #interrupt-cells = <1>;
> > + };
> > +
> > + serial at d0000000 {
> > + compatible = "arm,pl011", "arm,primecell";
> > + reg = <0xd0000000 0x1000>;
> > + interrupt-parent = <&vic0>;
> > + interrupts = <24>;
> > + };
> > +
> > + serial at d0080000 {
> > + compatible = "arm,pl011", "arm,primecell";
> > + reg = <0xd0080000 0x1000>;
> > + interrupt-parent = <&vic0>;
> > + interrupts = <25>;
> > + };
> > +
> > + /* local/cpu GPIO */
> > + gpio0: gpio at f0100000 {
> > + #gpio-cells = <2>;
> > + compatible = "arm,pl061", "arm,primecell";
> > + gpio-controller;
> > + reg = <0xf0100000 0x1000>;
> > + interrupt-parent = <&vic0>;
> > + interrupts = <18>;
> > + };
> > +
> > + /* basic GPIO */
> > + gpio1: gpio at fc980000 {
> > + #gpio-cells = <2>;
> > + compatible = "arm,pl061", "arm,primecell";
> > + gpio-controller;
> > + reg = <0xfc980000 0x1000>;
> > + interrupt-parent = <&vic1>;
> > + interrupts = <19>;
> > + };
> > +
> > + /* appl GPIO */
> > + gpio2: gpio at d8100000 {
> > + #gpio-cells = <2>;
> > + compatible = "arm,pl061", "arm,primecell";
> > + gpio-controller;
> > + reg = <0xd8100000 0x1000>;
> > + interrupt-parent = <&vic1>;
> > + interrupts = <4>;
> > + };
> > +
> > + gmac0: ethernet at e0800000 {
> > + compatible = "st,spear600-gmac";
> > + reg = <0xe0800000 0x8000>;
> > + interrupt-parent = <&vic1>;
> > + interrupts = <24 23>;
> > + interrupt-names = "macirq", "eth_wake_irq";
> > + mac-address = [000000000000]; /* Filled in by U-Boot
*/
> > + };
> > +
> > + i2c at d0200000 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + compatible = "snps,designware-i2c";
> > + reg = <0xd0200000 0x1000>;
> > + interrupt-parent = <&vic0>;
> > + interrupts = <28>;
> > + };
> > +
> > + fsmc0: flash at d1800000 {
> > + status = "disabled";
> > + compatible = "st,spear600-fsmc-nand";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + reg = <0xd1800000 0x1000 /* FSMC Register */
> > + 0xd2000000 0x4000>; /* NAND Base */
> > + reg-names = "fsmc_regs", "nand_data";
> > + };
> > +
> > + smi0: flash at fc000000 {
> > + status = "disabled";
> > + compatible = "st,spear600-smi";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + reg = <0xfc000000 0x1000>;
> > + interrupt-parent = <&vic1>;
> > + interrupts = <12>;
> > + };
> > +
> > + ehci at e1800000 {
> > + status = "disabled";
> > + compatible = "st,spear600-ehci", "usb-ehci";
> > + reg = <0xe1800000 0x1000>;
> > + interrupt-parent = <&vic1>;
> > + interrupts = <27>;
> > + };
> > +
> > + ehci at e2000000 {
> > + status = "disabled";
> > + compatible = "st,spear600-ehci", "usb-ehci";
> > + reg = <0xe2000000 0x1000>;
> > + interrupt-parent = <&vic1>;
> > + interrupts = <29>;
> > + };
> > +
> > + ohci at e1900000 {
> > + status = "disabled";
> > + compatible = "st,spear600-ohci", "usb-ohci";
> > + reg = <0xe1900000 0x1000>;
> > + interrupt-parent = <&vic1>;
> > + interrupts = <26>;
> > + };
> > +
> > + ohci at e2100000 {
> > + status = "disabled";
> > + compatible = "st,spear600-ohci", "usb-ohci";
> > + reg = <0xe2100000 0x1000>;
> > + interrupt-parent = <&vic1>;
> > + interrupts = <28>;
> > + };
>
> all of this need a Doc for the ST bindings
Sure. I only provided those nodes on Arnd's special request. They are
currently disabled. And documentation will follow with the DT device driver
patches.
> > + };
> > +};
> > diff --git a/arch/arm/mach-spear6xx/Kconfig
> > b/arch/arm/mach-spear6xx/Kconfig index ff4ae5b..7777f72 100644
> > --- a/arch/arm/mach-spear6xx/Kconfig
> > +++ b/arch/arm/mach-spear6xx/Kconfig
> > @@ -11,6 +11,13 @@ config BOARD_SPEAR600_EVB
> >
> > help
> >
> > Supports ST SPEAr600 Evaluation Board
> >
> > +config BOARD_SPEAR600_DT
> > + bool "SPEAr600 generic board configured via device-tree"
> > + select MACH_SPEAR600
> > + select USE_OF
> > + help
> > + Supports ST SPEAr600 boards configured via the device-tree
> > +
> >
> > endmenu
> >
> > config MACH_SPEAR600
> >
> > diff --git a/arch/arm/mach-spear6xx/Makefile
> > b/arch/arm/mach-spear6xx/Makefile index cc1a4d8..6f87c3a 100644
> > --- a/arch/arm/mach-spear6xx/Makefile
> > +++ b/arch/arm/mach-spear6xx/Makefile
> > @@ -5,8 +5,5 @@
> >
> > # common files
> > obj-y += clock.o spear6xx.o
> >
> > -# spear600 specific files
> > -obj-$(CONFIG_MACH_SPEAR600) += spear600.o
> > -
> >
> > # spear600 boards files
> > obj-$(CONFIG_BOARD_SPEAR600_EVB) += spear600_evb.o
> >
> > diff --git a/arch/arm/mach-spear6xx/spear600.c
> > b/arch/arm/mach-spear6xx/spear600.c deleted file mode 100644
> > index d0e6eea..0000000
> > --- a/arch/arm/mach-spear6xx/spear600.c
> > +++ /dev/null
> > @@ -1,25 +0,0 @@
> > -/*
> > - * arch/arm/mach-spear6xx/spear600.c
> > - *
> > - * SPEAr600 machine source file
> > - *
> > - * Copyright (C) 2009 ST Microelectronics
> > - * Rajeev Kumar<rajeev-dlh.kumar at st.com>
> > - *
> > - * This file is licensed under the terms of the GNU General Public
> > - * License version 2. This program is licensed "as is" without any
> > - * warranty of any kind, whether express or implied.
> > - */
> > -
> > -#include <linux/ptrace.h>
> > -#include <asm/irq.h>
> > -#include <mach/generic.h>
> > -#include <mach/hardware.h>
> > -
> > -/* Add spear600 specific devices here */
> > -
> > -void __init spear600_init(void)
> > -{
> > - /* call spear6xx family common init function */
> > - spear6xx_init();
> > -}
> > diff --git a/arch/arm/mach-spear6xx/spear600_evb.c
> > b/arch/arm/mach-spear6xx/spear600_evb.c index c6e4254..c4949aa 100644
> > --- a/arch/arm/mach-spear6xx/spear600_evb.c
> > +++ b/arch/arm/mach-spear6xx/spear600_evb.c
> > @@ -32,9 +32,6 @@ static void __init spear600_evb_init(void)
> >
> > {
> >
> > unsigned int i;
> >
> > - /* call spear600 machine init function */
> > - spear600_init();
> > -
> >
> > /* Add Platform Devices */
> > platform_add_devices(plat_devs, ARRAY_SIZE(plat_devs));
> >
> > diff --git a/arch/arm/mach-spear6xx/spear6xx.c
> > b/arch/arm/mach-spear6xx/spear6xx.c index e0f6628..aca20f0 100644
> > --- a/arch/arm/mach-spear6xx/spear6xx.c
> > +++ b/arch/arm/mach-spear6xx/spear6xx.c
> > @@ -6,6 +6,8 @@
> >
> > * Copyright (C) 2009 ST Microelectronics
> > * Rajeev Kumar<rajeev-dlh.kumar at st.com>
> > *
> >
> > + * Copyright 2012 Stefan Roese <sr at denx.de>
> > + *
> >
> > * This file is licensed under the terms of the GNU General Public
> > * License version 2. This program is licensed "as is" without any
> > * warranty of any kind, whether express or implied.
> >
> > @@ -15,6 +17,10 @@
> >
> > #include <linux/amba/pl061.h>
> > #include <linux/ptrace.h>
> > #include <linux/io.h>
> >
> > +#include <linux/of.h>
> > +#include <linux/of_address.h>
> > +#include <linux/of_irq.h>
> > +#include <linux/of_platform.h>
> >
> > #include <asm/hardware/vic.h>
> > #include <asm/irq.h>
> > #include <asm/mach/arch.h>
> >
> > @@ -99,12 +105,6 @@ struct amba_device gpio_device[] = {
> >
> > }
> >
> > };
> >
> > -/* This will add devices, and do machine specific tasks */
> > -void __init spear6xx_init(void)
> > -{
> > - /* nothing to do for now */
> > -}
> > -
> >
> > /* This will initialize vic */
> > void __init spear6xx_init_irq(void)
> > {
> >
> > @@ -181,3 +181,60 @@ static void __init spear6xx_timer_init(void)
> >
> > struct sys_timer spear6xx_timer = {
> >
> > .init = spear6xx_timer_init,
> >
> > };
> >
> > +
> > +/*
> > + * Devicetree specific init structs/functions:
> > + * Once the SPEAr600 devicetree support has matured, we can remove
> > + * spear600_evb.c and the non-devicetree support above in this file.
> > + */
> > +
> > +/*
> > + * Add auxdata so that clock name matching doesn't fail in device
> > + * drivers
> > + */
> > +struct of_dev_auxdata spear600_auxdata_lookup[] __initdata = {
> > + OF_DEV_AUXDATA("arm,pl011", SPEAR6XX_ICM1_UART0_BASE,
> > + "uart0", NULL),
> > + OF_DEV_AUXDATA("arm,pl011", SPEAR6XX_ICM1_UART1_BASE,
> > + "uart1", NULL),
> > + OF_DEV_AUXDATA("arm,pl061", SPEAR6XX_CPU_GPIO_BASE,
> > + "gpio0", NULL),
> > + OF_DEV_AUXDATA("arm,pl061", SPEAR6XX_ICM3_GPIO_BASE,
> > + "gpio1", NULL),
> > + OF_DEV_AUXDATA("arm,pl061", SPEAR6XX_ICM2_GPIO_BASE,
> > + "gpio2", NULL),
> > + OF_DEV_AUXDATA("snps,designware-i2c", SPEAR6XX_ICM1_I2C_BASE,
> > + "i2c_designware.0", NULL),
>
> update the clkdev no more OF_DEV_AUXDATA
That will break non-DT boards. We can change it in clkdev later, once DT
support has stabalized for SPEAr600. And remove all this then.
>
> please keep me in Cc
Sure.
Cheers,
Stefan
More information about the linux-arm-kernel
mailing list