[PATCH 08/12] gpio/twl: Allocate irq_desc dynamically for SPARSE_IRQ support

[Cousson, Benoit]

Hi Grant,

That fix is tightly coupled with the previous twl4030-irq change, so it 
will be good to pulled it with the twl series through MFD if you are OK 
with that?

Care to ack this one and the next one?

Thanks,
Benoit


On 3/2/2012 5:50 PM, Benoit Cousson wrote:
> Do not use the board pdata for irq_base, but allocate them dynamically
> to allow a proper support of SPARSE_IRQ.
>
> Fix an unneeded line wrap.
>
> Signed-off-by: Benoit Cousson<b-cousson at ti.com>
> Acked-by: Felipe Balbi<balbi at ti.com>
> ---
>   drivers/gpio/gpio-twl4030.c |   33 +++++++++++++++++----------------
>   1 files changed, 17 insertions(+), 16 deletions(-)
>
> diff --git a/drivers/gpio/gpio-twl4030.c b/drivers/gpio/gpio-twl4030.c
> index 697396c..49e5c6e 100644
> --- a/drivers/gpio/gpio-twl4030.c
> +++ b/drivers/gpio/gpio-twl4030.c
> @@ -395,23 +395,26 @@ static int gpio_twl4030_remove(struct platform_device *pdev);
>   static int __devinit gpio_twl4030_probe(struct platform_device *pdev)
>   {
>   	struct twl4030_gpio_platform_data *pdata = pdev->dev.platform_data;
> -	int ret;
> +	int ret, irq_base;
>
>   	/* maybe setup IRQs */
> -	if (pdata->irq_base) {
> -		if (is_module()) {
> -			dev_err(&pdev->dev,
> -				"can't dispatch IRQs from modules\n");
> -			goto no_irqs;
> -		}
> -		ret = twl4030_sih_setup(&pdev->dev, TWL4030_MODULE_GPIO,
> -					pdata->irq_base);
> -		if (ret<  0)
> -			return ret;
> -		WARN_ON(ret != pdata->irq_base);
> -		twl4030_gpio_irq_base = ret;
> +	if (is_module()) {
> +		dev_err(&pdev->dev, "can't dispatch IRQs from modules\n");
> +		goto no_irqs;
> +	}
> +
> +	irq_base = irq_alloc_descs(-1, 0, TWL4030_GPIO_MAX, 0);
> +	if (irq_base<  0) {
> +		dev_err(&pdev->dev, "Failed to alloc irq_descs\n");
> +		return irq_base;
>   	}
>
> +	ret = twl4030_sih_setup(&pdev->dev, TWL4030_MODULE_GPIO, irq_base);
> +	if (ret<  0)
> +		return ret;
> +
> +	twl4030_gpio_irq_base = irq_base;
> +
>   no_irqs:
>   	/*
>   	 * NOTE:  boards may waste power if they don't set pullups
> @@ -443,9 +446,7 @@ no_irqs:
>
>   	ret = gpiochip_add(&twl_gpiochip);
>   	if (ret<  0) {
> -		dev_err(&pdev->dev,
> -				"could not register gpiochip, %d\n",
> -				ret);
> +		dev_err(&pdev->dev, "could not register gpiochip, %d\n", ret);
>   		twl_gpiochip.ngpio = 0;
>   		gpio_twl4030_remove(pdev);
>   	} else if (pdata->setup) {