[PATCH v7 14/14] usb: chipidea: add imx platform driver
mkl at pengutronix.de
Wed Jun 27 05:46:07 EDT 2012
On 06/27/2012 08:20 AM, Richard Zhao wrote:
> On Mon, Jun 25, 2012 at 12:33:58PM +0200, Marc Kleine-Budde wrote:
>> On 06/25/2012 08:56 AM, Richard Zhao wrote:
>>> This patch supports only the host-mode functionality so far.
>>> Signed-off-by: Richard Zhao <richard.zhao at freescale.com>
>>> Signed-off-by: Marek Vasut <marex at denx.de>
>>> Cc: Peter Chen <peter.chen at freescale.com>
>>> Cc: Alexander Shishkin <alexander.shishkin at linux.intel.com>
>>> Cc: Felipe Balbi <balbi at ti.com>
>>> Cc: Greg Kroah-Hartman <gregkh at linuxfoundation.org>
>>> Tested-by: Subodh Nijsure <snijsure at grid-net.com>
>>> .../devicetree/bindings/usb/ci13xxx-imx.txt | 20 ++
>>> drivers/usb/chipidea/Makefile | 3 +
>>> drivers/usb/chipidea/ci13xxx_imx.c | 197 ++++++++++++++++++++
>>> 3 files changed, 220 insertions(+)
>>> create mode 100644 Documentation/devicetree/bindings/usb/ci13xxx-imx.txt
>>> create mode 100644 drivers/usb/chipidea/ci13xxx_imx.c
>>> diff --git a/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt
>>> new file mode 100644
>>> index 0000000..8bcd071
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt
>>> @@ -0,0 +1,20 @@
>>> +* Freescale i.MX ci13xxx usb controllers
>>> +Required properties:
>>> +- compatible: Should be "fsl,imx27-usb"
>>> +- reg: Should contain registers location and length
>>> +- interrupts: Should contain controller interrupt
>>> +Optional properties:
>>> +- fsl,usbphy: phandler of usb phy that connects to the only one port
>>> +- fsl,hub-reset-gpios: gpio used to reset on-board usb hub
>>> +- fsl,vbus-power-gpios: gpio used to set vbus power of the only one port
>> These two properties are not implemented, are they?
>> vbus is handled via a fixed regulator.
> I forgot to update the doc.
>> Further I'm looking into the phy and otg implementation. I think the
>> handling of the regulator should go into mxs-phy.c, not into the
> Normally, we don't put it in phy driver. For example, most host driver
> don't call phy drivers.
Yes, I've noticed that otg support is ... a bit messy in the linux
kernel. There are some drivers that implement a otg state machine.
However, I have the udc on mx28 somewhat working. It's still a hack
since I have to implement an otg driver for this, but the host part
doesn't do otg so far...and unplug is not detected correctly.
Pengutronix e.K. | Marc Kleine-Budde |
Industrial Linux Solutions | Phone: +49-231-2826-924 |
Vertretung West/Dortmund | Fax: +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de |
-------------- next part --------------
A non-text attachment was scrubbed...
Size: 262 bytes
Desc: OpenPGP digital signature
More information about the linux-arm-kernel