[PATCH v3] ARM: at91: add support for Telit EVK-PRO3 with Telit GE863-PRO3

[Fabio Porcedda]

Signed-off-by: Fabio Porcedda <fabio.porcedda at gmail.com>
---
 - changes for v3
	- split the evk-pro3 from the ge863-pro3 to facilitate
           the board customization
        - add usb gadget and macb
 - changes for v2
	- add empty line before the Signed-off-by line

 arch/arm/boot/dts/evk-pro3.dts    | 41 ++++++++++++++++++++++++++++++
 arch/arm/boot/dts/ge863-pro3.dtsi | 52 +++++++++++++++++++++++++++++++++++++++
 arch/arm/mach-at91/Makefile.boot  |  1 +
 3 files changed, 94 insertions(+)
 create mode 100644 arch/arm/boot/dts/evk-pro3.dts
 create mode 100644 arch/arm/boot/dts/ge863-pro3.dtsi

diff --git a/arch/arm/boot/dts/evk-pro3.dts b/arch/arm/boot/dts/evk-pro3.dts
new file mode 100644
index 0000000..b7354e6
--- /dev/null
+++ b/arch/arm/boot/dts/evk-pro3.dts
@@ -0,0 +1,41 @@
+/*
+ * evk-pro3.dts - Device Tree file for Telit EVK-PRO3 with Telit GE863-PRO3
+ *
+ * Copyright (C) 2012 Telit,
+ *               2012 Fabio Porcedda <fabio.porcedda at gmail.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/dts-v1/;
+
+/include/ "ge863-pro3.dtsi"
+
+/ {
+	model = "Telit EVK-PRO3 for Telit GE863-PRO3";
+	compatible = "telit,evk-pro3", "atmel,at91sam9260", "atmel,at91sam9";
+
+	ahb {
+		apb {
+			macb0: ethernet at fffc4000 {
+				phy-mode = "rmii";
+				status = "okay";
+			};
+
+			usb1: gadget at fffa4000 {
+				atmel,vbus-gpio = <&pioC 5 0>;
+				status = "okay";
+			};
+		};
+
+		usb0: ohci at 00500000 {
+			num-ports = <2>;
+			status = "okay";
+		};
+	};
+
+	i2c at 0 {
+		status = "okay";
+	};
+
+};
\ No newline at end of file
diff --git a/arch/arm/boot/dts/ge863-pro3.dtsi b/arch/arm/boot/dts/ge863-pro3.dtsi
new file mode 100644
index 0000000..17136fc
--- /dev/null
+++ b/arch/arm/boot/dts/ge863-pro3.dtsi
@@ -0,0 +1,52 @@
+/*
+ * ge863_pro3.dtsi - Device Tree file for Telit GE863-PRO3
+ *
+ * Copyright (C) 2012 Telit,
+ *               2012 Fabio Porcedda <fabio.porcedda at gmail.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/include/ "at91sam9260.dtsi"
+
+/ {
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		main_clock: clock at 0 {
+			compatible = "atmel,osc", "fixed-clock";
+			clock-frequency = <6000000>;
+		};
+	};
+
+	ahb {
+		apb {
+			dbgu: serial at fffff200 {
+				status = "okay";
+			};
+		};
+
+		nand0: nand at 40000000 {
+			nand-bus-width = <8>;
+			nand-ecc-mode = "soft";
+			nand-on-flash-bbt;
+			status = "okay";
+
+			boot at 0 {
+				label = "boot";
+				reg = <0x0 0x7c0000>;
+			};
+
+			root at 07c0000 {
+				label = "root";
+				reg = <0x7c0000 0x7840000>;
+			};
+		};
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs";
+	};
+};
diff --git a/arch/arm/mach-at91/Makefile.boot b/arch/arm/mach-at91/Makefile.boot
index 9e84fe4..11c3ca7 100644
--- a/arch/arm/mach-at91/Makefile.boot
+++ b/arch/arm/mach-at91/Makefile.boot
@@ -16,6 +16,7 @@ endif
 # Keep dtb files sorted alphabetically for each SoC
 # sam9260
 dtb-$(CONFIG_MACH_AT91SAM_DT) += ethernut5.dtb
+dtb-$(CONFIG_MACH_AT91SAM_DT) += evk-pro3.dtb
 dtb-$(CONFIG_MACH_AT91SAM_DT) += tny_a9260.dtb
 dtb-$(CONFIG_MACH_AT91SAM_DT) += usb_a9260.dtb
 # sam9263
-- 
1.7.11.1