[PATCH v3 3/7] ARM: at91: remove static irq priorities for sam9x5

[Nicolas Ferre]

On 06/23/2012 06:05 PM, ludovic.desroches at atmel.com :
> From: Ludovic Desroches <ludovic.desroches at atmel.com>
> 
> Since irq priorites are managed in DT, static ones are no more required for
> sam9x5 which only has DT support.
> 
> Signed-off-by: Ludovic Desroches <ludovic.desroches at atmel.com>

Acked-by: Nicolas Ferre <nicolas.ferre at atmel.com>

> ---
>  arch/arm/mach-at91/at91sam9x5.c |   38 --------------------------------------
>  1 files changed, 0 insertions(+), 38 deletions(-)
> 
> diff --git a/arch/arm/mach-at91/at91sam9x5.c b/arch/arm/mach-at91/at91sam9x5.c
> index 537710b..477cf9d 100644
> --- a/arch/arm/mach-at91/at91sam9x5.c
> +++ b/arch/arm/mach-at91/at91sam9x5.c
> @@ -319,47 +319,9 @@ void __init at91sam9x5_initialize(void)
>  /* --------------------------------------------------------------------
>   *  Interrupt initialization
>   * -------------------------------------------------------------------- */
> -/*
> - * The default interrupt priority levels (0 = lowest, 7 = highest).
> - */
> -static unsigned int at91sam9x5_default_irq_priority[NR_AIC_IRQS] __initdata = {
> -	7,	/* Advanced Interrupt Controller (FIQ) */
> -	7,	/* System Peripherals */
> -	1,	/* Parallel IO Controller A and B */
> -	1,	/* Parallel IO Controller C and D */
> -	4,	/* Soft Modem */
> -	5,	/* USART 0 */
> -	5,	/* USART 1 */
> -	5,	/* USART 2 */
> -	5,	/* USART 3 */
> -	6,	/* Two-Wire Interface 0 */
> -	6,	/* Two-Wire Interface 1 */
> -	6,	/* Two-Wire Interface 2 */
> -	0,	/* Multimedia Card Interface 0 */
> -	5,	/* Serial Peripheral Interface 0 */
> -	5,	/* Serial Peripheral Interface 1 */
> -	5,	/* UART 0 */
> -	5,	/* UART 1 */
> -	0,	/* Timer Counter 0, 1, 2, 3, 4 and 5 */
> -	0,	/* Pulse Width Modulation Controller */
> -	0,	/* ADC Controller */
> -	0,	/* DMA Controller 0 */
> -	0,	/* DMA Controller 1 */
> -	2,	/* USB Host High Speed port */
> -	2,	/* USB Device High speed port */
> -	3,	/* Ethernet MAC 0 */
> -	3,	/* LDC Controller or Image Sensor Interface */
> -	0,	/* Multimedia Card Interface 1 */
> -	3,	/* Ethernet MAC 1 */
> -	4,	/* Synchronous Serial Interface */
> -	4,	/* CAN Controller 0 */
> -	4,	/* CAN Controller 1 */
> -	0,	/* Advanced Interrupt Controller (IRQ0) */
> -};
>  
>  struct at91_init_soc __initdata at91sam9x5_soc = {
>  	.map_io = at91sam9x5_map_io,
> -	.default_irq_priority = at91sam9x5_default_irq_priority,
>  	.register_clocks = at91sam9x5_register_clocks,
>  	.init = at91sam9x5_initialize,
>  };
> 


-- 
Nicolas Ferre