[PATCH v7 14/14] usb: chipidea: add imx platform driver
Richard Zhao
richard.zhao at freescale.com
Mon Jun 25 02:56:31 EDT 2012
This patch supports only the host-mode functionality so far.
Signed-off-by: Richard Zhao <richard.zhao at freescale.com>
Signed-off-by: Marek Vasut <marex at denx.de>
Cc: Peter Chen <peter.chen at freescale.com>
Cc: Alexander Shishkin <alexander.shishkin at linux.intel.com>
Cc: Felipe Balbi <balbi at ti.com>
Cc: Greg Kroah-Hartman <gregkh at linuxfoundation.org>
Tested-by: Subodh Nijsure <snijsure at grid-net.com>
---
.../devicetree/bindings/usb/ci13xxx-imx.txt | 20 ++
drivers/usb/chipidea/Makefile | 3 +
drivers/usb/chipidea/ci13xxx_imx.c | 197 ++++++++++++++++++++
3 files changed, 220 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/ci13xxx-imx.txt
create mode 100644 drivers/usb/chipidea/ci13xxx_imx.c
diff --git a/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt
new file mode 100644
index 0000000..8bcd071
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt
@@ -0,0 +1,20 @@
+* Freescale i.MX ci13xxx usb controllers
+
+Required properties:
+- compatible: Should be "fsl,imx27-usb"
+- reg: Should contain registers location and length
+- interrupts: Should contain controller interrupt
+
+Optional properties:
+- fsl,usbphy: phandler of usb phy that connects to the only one port
+- fsl,hub-reset-gpios: gpio used to reset on-board usb hub
+- fsl,vbus-power-gpios: gpio used to set vbus power of the only one port
+
+Examples:
+usb at 02184000 { /* USB OTG */
+ compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
+ reg = <0x02184000 0x200>;
+ interrupts = <0 43 0x04>;
+ fsl,usbphy = <&usbphy1>;
+ fsl,vbus-power-gpios = <&gpio3 22 0>;
+};
diff --git a/drivers/usb/chipidea/Makefile b/drivers/usb/chipidea/Makefile
index b69900a..5c66d9c 100644
--- a/drivers/usb/chipidea/Makefile
+++ b/drivers/usb/chipidea/Makefile
@@ -14,3 +14,6 @@ ifneq ($(CONFIG_PCI),)
obj-$(CONFIG_USB_CHIPIDEA) += ci13xxx_pci.o
endif
+ifneq ($(CONFIG_OF_DEVICE),)
+ obj-$(CONFIG_USB_CHIPIDEA) += ci13xxx_imx.o
+endif
diff --git a/drivers/usb/chipidea/ci13xxx_imx.c b/drivers/usb/chipidea/ci13xxx_imx.c
new file mode 100644
index 0000000..efae2be
--- /dev/null
+++ b/drivers/usb/chipidea/ci13xxx_imx.c
@@ -0,0 +1,197 @@
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright (C) 2012 Marek Vasut <marex at denx.de>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/dma-mapping.h>
+#include <linux/usb/chipidea.h>
+#include <linux/clk.h>
+#include <linux/regulator/consumer.h>
+
+#include "ci.h"
+
+#define pdev_to_phy(pdev) \
+ ((struct usb_phy *)platform_get_drvdata(pdev))
+
+struct ci13xxx_imx_data {
+ struct device_node *phy_np;
+ struct usb_phy *phy;
+ struct platform_device *ci_pdev;
+ struct clk *clk;
+ struct regulator *reg_vbus;
+};
+
+static struct ci13xxx_platform_data ci13xxx_imx_platdata __devinitdata = {
+ .name = "ci13xxx_imx",
+ .flags = CI13XXX_REQUIRE_TRANSCEIVER |
+ CI13XXX_PULLUP_ON_VBUS |
+ CI13XXX_DISABLE_STREAMING,
+ .capoffset = DEF_CAPOFFSET,
+};
+
+static int __devinit ci13xxx_imx_probe(struct platform_device *pdev)
+{
+ struct ci13xxx_imx_data *data;
+ struct platform_device *plat_ci, *phy_pdev;
+ struct device_node *phy_np;
+ struct resource *res;
+ struct regulator *reg_vbus;
+ int ret;
+
+ data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+ if (!data) {
+ dev_err(&pdev->dev, "Failed to allocate CI13xxx-IMX data!\n");
+ return -ENOMEM;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "Can't get device resources!\n");
+ return -ENOENT;
+ }
+
+ data->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(data->clk)) {
+ dev_err(&pdev->dev,
+ "Failed to get clock, err=%ld\n", PTR_ERR(data->clk));
+ return PTR_ERR(data->clk);
+ }
+
+ ret = clk_prepare_enable(data->clk);
+ if (ret) {
+ dev_err(&pdev->dev,
+ "Failed to prepare or enable clock, err=%d\n", ret);
+ return ret;
+ }
+
+ phy_np = of_parse_phandle(pdev->dev.of_node, "fsl,usbphy", 0);
+ if (phy_np) {
+ data->phy_np = phy_np;
+ phy_pdev = of_find_device_by_node(phy_np);
+ if (phy_pdev) {
+ struct usb_phy *phy;
+ phy = pdev_to_phy(phy_pdev);
+ if (phy &&
+ try_module_get(phy_pdev->dev.driver->owner)) {
+ usb_phy_init(phy);
+ data->phy = phy;
+ }
+ }
+ }
+
+ /* we only support host now, so enable vbus here */
+ reg_vbus = devm_regulator_get(&pdev->dev, "vbus");
+ if (!IS_ERR(reg_vbus)) {
+ ret = regulator_enable(reg_vbus);
+ if (ret) {
+ dev_err(&pdev->dev,
+ "Failed to enable vbus regulator, err=%d\n",
+ ret);
+ goto put_np;
+ }
+ data->reg_vbus = reg_vbus;
+ } else {
+ reg_vbus = NULL;
+ }
+
+ ci13xxx_imx_platdata.phy = data->phy;
+
+ if (!pdev->dev.dma_mask) {
+ pdev->dev.dma_mask = devm_kzalloc(&pdev->dev,
+ sizeof(*pdev->dev.dma_mask), GFP_KERNEL);
+ if (!pdev->dev.dma_mask) {
+ ret = -ENOMEM;
+ dev_err(&pdev->dev, "Failed to alloc dma_mask!\n");
+ goto err;
+ }
+ *pdev->dev.dma_mask = DMA_BIT_MASK(32);
+ dma_set_coherent_mask(&pdev->dev, *pdev->dev.dma_mask);
+ }
+ plat_ci = ci13xxx_add_device(&pdev->dev,
+ pdev->resource, pdev->num_resources,
+ &ci13xxx_imx_platdata);
+ if (IS_ERR(plat_ci)) {
+ ret = PTR_ERR(plat_ci);
+ dev_err(&pdev->dev,
+ "Can't register ci_hdrc platform device, err=%d\n",
+ ret);
+ goto err;
+ }
+
+ data->ci_pdev = plat_ci;
+ platform_set_drvdata(pdev, data);
+
+ pm_runtime_no_callbacks(&pdev->dev);
+ pm_runtime_enable(&pdev->dev);
+
+ return 0;
+
+err:
+ if (reg_vbus)
+ regulator_disable(reg_vbus);
+put_np:
+ if (phy_np)
+ of_node_put(phy_np);
+ clk_disable_unprepare(data->clk);
+ return ret;
+}
+
+static int __devexit ci13xxx_imx_remove(struct platform_device *pdev)
+{
+ struct ci13xxx_imx_data *data = platform_get_drvdata(pdev);
+
+ ci13xxx_remove_device(data->ci_pdev);
+
+ if (data->reg_vbus)
+ regulator_disable(data->reg_vbus);
+
+ if (data->phy) {
+ usb_phy_shutdown(data->phy);
+ module_put(data->phy->dev->driver->owner);
+ }
+
+ of_node_put(data->phy_np);
+
+ clk_disable_unprepare(data->clk);
+
+ platform_set_drvdata(pdev, NULL);
+
+ return 0;
+}
+
+static const struct of_device_id ci13xxx_imx_dt_ids[] = {
+ { .compatible = "fsl,imx27-usb", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, ci13xxx_imx_dt_ids);
+
+static struct platform_driver ci13xxx_imx_driver = {
+ .probe = ci13xxx_imx_probe,
+ .remove = __devexit_p(ci13xxx_imx_remove),
+ .driver = {
+ .name = "imx_usb",
+ .owner = THIS_MODULE,
+ .of_match_table = ci13xxx_imx_dt_ids,
+ },
+};
+
+module_platform_driver(ci13xxx_imx_driver);
+
+MODULE_ALIAS("platform:imx-usb");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("CI13xxx i.MX USB binding");
+MODULE_AUTHOR("Marek Vasut <marex at denx.de>");
+MODULE_AUTHOR("Richard Zhao <richard.zhao at freescale.com>");
--
1.7.9.5
More information about the linux-arm-kernel
mailing list