[PATCH 2/2] ARM: MXS: Add Crystalfontz CFA-10036 DTS

[Marek Vasut]

Dear Maxime Ripard,

> Hi Marek,
> 
> Le 21/06/2012 11:49, Marek Vasut a écrit :
> > Dear Maxime Ripard,
> > 
> >> Signed-off-by: Maxime Ripard <maxime.ripard at free-electrons.com>
> >> 
> >> Cc: Brian Lily <brian at crystalfontz.com>
> > 
> > But then, wait ... why did you add the mach-cfa10036.c entry?
> 
> As I stated in my introduction mail, I first did the job on 3.4 before
> forward porting it to 3.5. And since the MMC part worked on 3.4 and no
> longer on 3.5, I wanted to keep an easily trackable file between these
> two versions, which is not the case with DT.
> 
> So partly historical, partly debugging reasons :)
> 
> Anyway, I totally understand your point, I'll remove the board file for
> the next postings.
> 
> >> ---
> >> 
> >>  arch/arm/boot/dts/cfa10036.dts |   66
> >> 
> >> ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 66
> >> insertions(+)
> >> 
> >>  create mode 100644 arch/arm/boot/dts/cfa10036.dts
> >> 
> >> diff --git a/arch/arm/boot/dts/cfa10036.dts
> >> b/arch/arm/boot/dts/cfa10036.dts new file mode 100644
> >> index 0000000..ceae960
> >> --- /dev/null
> >> +++ b/arch/arm/boot/dts/cfa10036.dts
> >> @@ -0,0 +1,66 @@
> >> +/*
> >> + * Copyright 2012 Free Electrons
> >> + *
> >> + * The code contained herein is licensed under the GNU General Public
> >> + * License. You may obtain a copy of the GNU General Public License
> >> + * Version 2 or later at the following locations:
> >> + *
> >> + * http://www.opensource.org/licenses/gpl-license.html
> >> + * http://www.gnu.org/copyleft/gpl.html
> >> + */
> >> +
> >> +/dts-v1/;
> >> +/include/ "imx28.dtsi"
> >> +
> >> +/ {
> >> +	model = "Crystalfontz CFA-10036 Board";
> >> +	compatible = "crystalfontz,cfa10036", "fsl,imx28-evk", "fsl,imx28";
> >> +
> >> +	memory {
> >> +		reg = <0x40000000 0x08000000>;
> >> +	};
> >> +
> >> +	apb at 80000000 {
> >> +		apbh at 80000000 {
> >> +			ssp0: ssp at 80010000 {
> >> +				compatible = "fsl,imx28-mmc";
> >> +				pinctrl-names = "default";
> >> +				pinctrl-0 = <&mmc0_4bit_pins_a
> >> +					&mmc0_cd_cfg &mmc0_sck_cfg>;
> >> +				bus-width = <4>;
> >> +				status = "okay";
> >> +			};
> >> +			pinctrl at 80018000 {
> >> +				#address-cells = <1>;
> >> +				#size-cells = <0>;
> >> +				compatible = "fsl,imx28-pinctrl", "simple-bus";
> >> +				reg = <0x80018000 2000>;
> >> +
> >> +				mmc0_4bit_pins_a: mmc0-4bit at 0 {
> >> +					reg = <0>;
> >> +					fsl,pinmux-ids = <0x2000 0x2010 0x2020
> >> +						0x2030 0x2080 0x2090 0x20a0>;
> >> +					fsl,drive-strength = <1>;
> >> +					fsl,voltage = <1>;
> >> +					fsl,pull-up = <1>;
> > 
> > Do you need this copy here?
> 
> This is not a direct copy, as there is only 4 pins for the MMC bus on
> this board, and one of the pins used for the additional bus pins on the
> imx28evk is used to power the OLED screen on this one, so I don't want
> all of the imx28 pins allocated for the mmc0 to be muxed as such.

Aha!

> Anyway, I'm not very familiar with pinctrl yet, so I might be missing
> something.

It's completely crazy and it's still going to be adjusted anyway.

> >> +				};
> >> +
> >> +				duart_pins_a: duart at 0 {
> >> +					reg = <0>;
> >> +					fsl,pinmux-ids = <0x3022 0x3032>;
> >> +					fsl,drive-strength = <0>;
> >> +					fsl,voltage = <1>;
> >> +					fsl,pull-up = <0>;
> > 
> > And this?
> 
> The pins to be muxed for the DUART differs from the imx28 here as well.
> On the iMX28EVK, the pins used for the DUART are 3-16 and 3-17, while we
> use the 3-2 and 3-3 on this board.

Understood

> >> +				};
> >> +			};
> >> +		};
> >> +
> >> +		apbx at 80040000 {
> >> +			duart: serial at 80074000 {
> >> +				pinctrl-names = "default";
> >> +				pinctrl-0 = <&duart_pins_a>;
> >> +				status = "okay";
> >> +			};
> >> +		};
> >> +	};
> >> +};
> 
> Thanks!
> 
> Maxime

Best regards,
Marek Vasut