[RFC PATCH v2 05/11] mfd: omap: control: usb-phy: introduce the ctrl-module usb driver
Konstantin Baydarov
kbaidarov at dev.rtsoft.ru
Mon Jun 18 07:32:26 EDT 2012
Created a new platform driver for the platform device created by the
control module mfd core, wrt usb. This driver has API's to power on/off
the phy and the API's to write to musb mailbox.
Changes since previous version:
- Bandgap and usb phy: drivers are now independent from control module driver, they use their own API functions.
Dependency was removed from Kconfig.
- Bandgap and usb phy: Added private spinlocks for bandgap and usb drivers.
(p.s. the mailbox for musb in omap4 is present in system control
module)
[kishon at ti.com: wrote the original API's related to USB functions]
Signed-off-by: Konstantin Baydarov <kbaidarov at dev.rtsoft.ru>
Signed-off-by: Kishon Vijay Abraham I <kishon at ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin at ti.com>
---
drivers/usb/otg/Kconfig | 12 ++
drivers/usb/otg/Makefile | 1
drivers/usb/otg/omap4-usb-phy.c | 167 ++++++++++++++++++++++++++++++++++++++
include/linux/usb/omap4_usb_phy.h | 53 ++++++++++++
4 files changed, 233 insertions(+)
Index: linux-2.6/drivers/usb/otg/Kconfig
===================================================================
--- linux-2.6.orig/drivers/usb/otg/Kconfig
+++ linux-2.6/drivers/usb/otg/Kconfig
@@ -78,6 +78,18 @@ config TWL6030_USB
are hooked to this driver through platform_data structure.
The definition of internal PHY APIs are in the mach-omap2 layer.
+config OMAP4_USB_PHY
+ tristate "Texas Instruments OMAP4+ USB pin control driver"
+ help
+ If you say yes here you get support for the Texas Instruments
+ OMAP4+ USB pin control driver. The register set is part of system
+ control module.
+
+ USB phy in OMAP configures control module register for powering on
+ the phy, configuring VBUSVALID, AVALID, IDDIG and SESSEND. For
+ performing the above mentioned configuration, API's are added in
+ by this children of the control module driver.
+
config NOP_USB_XCEIV
tristate "NOP USB Transceiver Driver"
select USB_OTG_UTILS
Index: linux-2.6/drivers/usb/otg/Makefile
===================================================================
--- linux-2.6.orig/drivers/usb/otg/Makefile
+++ linux-2.6/drivers/usb/otg/Makefile
@@ -13,6 +13,7 @@ obj-$(CONFIG_USB_GPIO_VBUS) += gpio_vbus
obj-$(CONFIG_ISP1301_OMAP) += isp1301_omap.o
obj-$(CONFIG_TWL4030_USB) += twl4030-usb.o
obj-$(CONFIG_TWL6030_USB) += twl6030-usb.o
+obj-$(CONFIG_OMAP4_USB_PHY) += omap4-usb-phy.o
obj-$(CONFIG_NOP_USB_XCEIV) += nop-usb-xceiv.o
obj-$(CONFIG_USB_ULPI) += ulpi.o
obj-$(CONFIG_USB_ULPI_VIEWPORT) += ulpi_viewport.o
Index: linux-2.6/drivers/usb/otg/omap4-usb-phy.c
===================================================================
--- /dev/null
+++ linux-2.6/drivers/usb/otg/omap4-usb-phy.c
@@ -0,0 +1,167 @@
+/*
+ * OMAP4 system control module driver, USB control children
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Contact:
+ * Kishon Vijay Abraham I <kishon at ti.com>
+ * Eduardo Valentin <eduardo.valentin at ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/usb/omap4_usb_phy.h>
+
+void __iomem *omap_usb_phy_base;
+spinlock_t omap_usb_phy_lock;
+
+static int omap_usb_phy_readl(u32 reg, u32 *val)
+{
+ if (!omap_usb_phy_base)
+ return -EINVAL;
+
+ *val = __raw_readl(omap_usb_phy_base + reg);
+ return 0;
+}
+
+/*
+ * TODO: Get rid from omap_usb_phy_writel() return value -
+ * It's useless.
+ */
+static int omap_usb_phy_writel(u32 val, u32 reg)
+{
+ unsigned long flags;
+
+ if (!omap_usb_phy_base)
+ return -EINVAL;
+
+ spin_lock_irqsave(&omap_usb_phy_lock, flags);
+ __raw_writel(val, omap_usb_phy_base + reg);
+ spin_unlock_irqrestore(&omap_usb_phy_lock, flags);
+ return 0;
+}
+
+/**
+ * omap4_usb_phy_power - power on/off the phy using control module reg
+ * @dev: struct device *
+ * @on: 0 or 1, based on powering on or off the PHY
+ *
+ * omap_usb2 can call this API to power on or off the PHY.
+ */
+int omap4_usb_phy_power(struct device *dev, int on)
+{
+ u32 val;
+ int ret;
+
+ if (on) {
+ ret = omap_usb_phy_readl(CONTROL_DEV_CONF, &val);
+ if (!ret && (val & PHY_PD)) {
+ ret = omap_usb_phy_writel(~PHY_PD,
+ CONTROL_DEV_CONF);
+ /* XXX: add proper documentation for this delay */
+ mdelay(200);
+ }
+ } else
+ ret = omap_usb_phy_writel(PHY_PD, CONTROL_DEV_CONF);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(omap4_usb_phy_power);
+
+/**
+ * omap4_usb_phy_mailbox - write to usb otg mailbox
+ * @dev: struct device *
+ * @val: the value to be written to the mailbox
+ *
+ * On detection of a device (ID pin is grounded), the phy should call this API
+ * to set AVALID, VBUSVALID and ID pin is grounded.
+ *
+ * When OMAP is connected to a host (OMAP in device mode), the phy should call
+ * this API to set AVALID, VBUSVALID and ID pin in high impedance.
+ *
+ * The phy should call this API, if OMAP is disconnected from host or device.
+ */
+int omap4_usb_phy_mailbox(struct device *dev, u32 val)
+{
+ return omap_usb_phy_writel(val, CONTROL_USBOTGHS_CONTROL);
+}
+EXPORT_SYMBOL_GPL(omap4_usb_phy_mailbox);
+
+static int __devinit omap_usb_phy_probe(struct platform_device *pdev)
+{
+ struct resource *io_res;
+
+// printk("\n\t\t **** omap_usb_phy_probe(): enter ");
+
+ io_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!io_res)
+ return -ENOENT;
+
+// printk("\n\t\t **** omap_usb_phy_probe(): start %x ", io_res->start);
+// printk("\n\t\t **** omap_usb_phy_probe(): size %x ", resource_size(io_res));
+ omap_usb_phy_base = ioremap(io_res->start, resource_size(io_res));
+// printk("\n\t\t **** omap_usb_phy_probe(): omap_usb_phy_base %x ", omap_usb_phy_base);
+ if (!omap_usb_phy_base)
+ return -ENOMEM;
+
+ /* Initialize register lock */
+ spin_lock_init(&omap_usb_phy_lock);
+
+ return 0;
+}
+
+static int __devexit omap_usb_phy_remove(struct platform_device *pdev)
+{
+ return 0;
+}
+
+static const struct of_device_id of_omap_usb_phy_match[] = {
+ { .compatible = "ti,omap4-usb-phy", },
+ { },
+};
+
+static struct platform_driver omap_usb_phy_driver = {
+ .probe = omap_usb_phy_probe,
+ .remove = __devexit_p(omap_usb_phy_remove),
+ .driver = {
+ .name = "omap4-usb-phy",
+ .owner = THIS_MODULE,
+ .of_match_table = of_omap_usb_phy_match,
+ },
+};
+
+static int __init omap_usb_phy_init(void)
+{
+ return platform_driver_register(&omap_usb_phy_driver);
+}
+postcore_initcall(omap_usb_phy_init);
+
+static void __exit omap_usb_phy_exit(void)
+{
+ platform_driver_unregister(&omap_usb_phy_driver);
+}
+module_exit(omap_usb_phy_exit);
+
+MODULE_DESCRIPTION("OMAP4+ USB-phy driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform: omap4-usb-phy");
+MODULE_AUTHOR("Texas Instrument Inc.");
Index: linux-2.6/include/linux/usb/omap4_usb_phy.h
===================================================================
--- /dev/null
+++ linux-2.6/include/linux/usb/omap4_usb_phy.h
@@ -0,0 +1,53 @@
+/*
+ * OMAP4 USB-phy
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Contact:
+ * Kishon Vijay Abraham I <kishon at ti.com>
+ * Eduardo Valentin <eduardo.valentin at ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#ifndef __OMAP4_USB_PHY_H
+#define __OMAP4_USB_PHY_H
+
+#define PHY_PD 0x1
+#define AVALID BIT(0)
+#define BVALID BIT(1)
+#define VBUSVALID BIT(2)
+#define SESSEND BIT(3)
+#define IDDIG BIT(4)
+#define CONTROL_DEV_CONF 0x00000300
+#define CONTROL_USBOTGHS_CONTROL 0x0000033C
+
+/* USB-PHY helpers */
+#if (defined(CONFIG_OMAP4_USB_PHY)) || (defined(CONFIG_OMAP4_USB_PHY_MODULE))
+extern int omap4_usb_phy_mailbox(struct device *dev, u32 val);
+extern int omap4_usb_phy_power(struct device *dev, int on);
+#else
+static inline int omap4_usb_phy_mailbox(struct device *dev, u32 val)
+{
+ return 0;
+}
+static inline int omap4_usb_phy_power(struct device *dev, int on)
+{
+ return 0;
+}
+#endif
+
+#endif
More information about the linux-arm-kernel
mailing list