[PATCH v3] ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset fix issues.
Munegowda, Keshava
keshava_mgowda at ti.com
Mon Jun 18 04:29:14 EDT 2012
On Fri, Jun 15, 2012 at 12:36 AM, Sarashetti, Mantesh <mantesh at ti.com> wrote:
> 'Acked-by: mantesh at ti.com'
> 'Tested-by: mantesh at ti.com'
>
> Regards,
> Mantesh
> -----Original Message-----
> From: Russ Dill [mailto:russ.dill at gmail.com] On Behalf Of Dill, Russ
> Sent: Thursday, June 14, 2012 11:24 AM
> To: linux-omap at vger.kernel.org; linux-arm-kernel at lists.infradead.org
> Cc: Balbi, Felipe; Munegowda, Keshava; Partha Basak; Igor Grinberg; Samuel Ortiz; Sarashetti, Mantesh; Setty, Sapna; Russ Dill
> Subject: [PATCH v3] ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset fix issues.
>
> From: Russ Dill <Russ.Dill at gmail.com>
>
> 'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' (1fcb57d0) fixes
> an issue where the ULPI PHYs were not held in reset while initializing
> the EHCI controller. However, it also changes behavior in
> omap-usb-host.c omap_usbhs_init by releasing reset while the
> configuration in that function was done.
>
> This change caused a regression on BB-xM where USB would not function
> if 'usb start' had been run from u-boot before booting. A change was
> made to release reset a little bit earlier which fixed the issue on
> BB-xM and did not cause any regressions on 3430 sdp, the board for
> which the fix was originally made.
>
> This new fix, 'USB: EHCI: OMAP: Finish ehci omap phy reset cycle
> before adding hcd.', (3aa2ae74) caused a regression on OMAP5.
>
> The original fix to hold the EHCI controller in reset during
> initialization was correct, however it appears that changing
> omap_usbhs_init to not hold the PHYs in reset during it's
> configuration was incorrect. This patch first reverts both fixes, and
> then changes ehci_hcd_omap_probe in ehci-omap.c to hold the PHYs in
> reset as the original patch had done. It also is sure to incorporate
> the _cansleep change that has been made in the meantime.
>
> I've tested this on Beagleboard xM, I'd really like to get an ack from
> the 3430 sdp and OMAP5 guys before getting this merged.
>
> v3 - Brown paper bag its too early in the morning actually run
> git commit amend fix
> v2 - Put cansleep gpiolib call outside of spinlock
>
> Signed-off-by: Russ Dill <Russ.Dill at gmail.com>
> ---
> drivers/mfd/omap-usb-host.c | 48 +++++++++++++++++++++++++++++++++++++++++-
> drivers/usb/host/ehci-omap.c | 18 +++++++---------
> 2 files changed, 55 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
> index 7e96bb2..41088ec 100644
> --- a/drivers/mfd/omap-usb-host.c
> +++ b/drivers/mfd/omap-usb-host.c
> @@ -25,6 +25,7 @@
> #include <linux/clk.h>
> #include <linux/dma-mapping.h>
> #include <linux/spinlock.h>
> +#include <linux/gpio.h>
> #include <plat/cpu.h>
> #include <plat/usb.h>
> #include <linux/pm_runtime.h>
> @@ -500,8 +501,21 @@ static void omap_usbhs_init(struct device *dev)
> dev_dbg(dev, "starting TI HSUSB Controller\n");
>
> pm_runtime_get_sync(dev);
> - spin_lock_irqsave(&omap->lock, flags);
>
> + if (pdata->ehci_data->phy_reset) {
> + if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[0]))
> + gpio_request_one(pdata->ehci_data->reset_gpio_port[0],
> + GPIOF_OUT_INIT_LOW, "USB1 PHY reset");
> +
> + if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[1]))
> + gpio_request_one(pdata->ehci_data->reset_gpio_port[1],
> + GPIOF_OUT_INIT_LOW, "USB2 PHY reset");
> +
> + /* Hold the PHY in RESET for enough time till DIR is high */
> + udelay(10);
> + }
> +
> + spin_lock_irqsave(&omap->lock, flags);
> omap->usbhs_rev = usbhs_read(omap->uhh_base, OMAP_UHH_REVISION);
> dev_dbg(dev, "OMAP UHH_REVISION 0x%x\n", omap->usbhs_rev);
>
> @@ -581,9 +595,39 @@ static void omap_usbhs_init(struct device *dev)
> }
>
> spin_unlock_irqrestore(&omap->lock, flags);
> +
> + if (pdata->ehci_data->phy_reset) {
> + /* Hold the PHY in RESET for enough time till
> + * PHY is settled and ready
> + */
> + udelay(10);
> +
> + if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[0]))
> + gpio_set_value_cansleep
> + (pdata->ehci_data->reset_gpio_port[0], 1);
> +
> + if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[1]))
> + gpio_set_value_cansleep
> + (pdata->ehci_data->reset_gpio_port[1], 1);
> + }
> +
> pm_runtime_put_sync(dev);
> }
>
> +static void omap_usbhs_deinit(struct device *dev)
> +{
> + struct usbhs_hcd_omap *omap = dev_get_drvdata(dev);
> + struct usbhs_omap_platform_data *pdata = &omap->platdata;
> +
> + if (pdata->ehci_data->phy_reset) {
> + if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[0]))
> + gpio_free(pdata->ehci_data->reset_gpio_port[0]);
> +
> + if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[1]))
> + gpio_free(pdata->ehci_data->reset_gpio_port[1]);
> + }
> +}
> +
>
> /**
> * usbhs_omap_probe - initialize TI-based HCDs
> @@ -767,6 +811,7 @@ static int __devinit usbhs_omap_probe(struct platform_device *pdev)
> goto end_probe;
>
> err_alloc:
> + omap_usbhs_deinit(&pdev->dev);
> iounmap(omap->tll_base);
>
> err_tll:
> @@ -818,6 +863,7 @@ static int __devexit usbhs_omap_remove(struct platform_device *pdev)
> {
> struct usbhs_hcd_omap *omap = platform_get_drvdata(pdev);
>
> + omap_usbhs_deinit(&pdev->dev);
> iounmap(omap->tll_base);
> iounmap(omap->uhh_base);
> clk_put(omap->init_60m_fclk);
> diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
> index a44294d..d0815b6 100644
> --- a/drivers/usb/host/ehci-omap.c
> +++ b/drivers/usb/host/ehci-omap.c
> @@ -192,14 +192,13 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
> }
> }
>
> + /* Hold PHYs in reset while initializing EHCI controller */
> if (pdata->phy_reset) {
> if (gpio_is_valid(pdata->reset_gpio_port[0]))
> - gpio_request_one(pdata->reset_gpio_port[0],
> - GPIOF_OUT_INIT_LOW, "USB1 PHY reset");
> + gpio_set_value_cansleep(pdata->reset_gpio_port[0], 0);
>
> if (gpio_is_valid(pdata->reset_gpio_port[1]))
> - gpio_request_one(pdata->reset_gpio_port[1],
> - GPIOF_OUT_INIT_LOW, "USB2 PHY reset");
> + gpio_set_value_cansleep(pdata->reset_gpio_port[1], 0);
>
> /* Hold the PHY in RESET for enough time till DIR is high */
> udelay(10);
> @@ -241,6 +240,11 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
> omap_ehci->hcs_params = readl(&omap_ehci->caps->hcs_params);
>
> ehci_reset(omap_ehci);
> + ret = usb_add_hcd(hcd, irq, IRQF_SHARED);
> + if (ret) {
> + dev_err(dev, "failed to add hcd with err %d\n", ret);
> + goto err_add_hcd;
> + }
>
> if (pdata->phy_reset) {
> /* Hold the PHY in RESET for enough time till
> @@ -255,12 +259,6 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
> gpio_set_value_cansleep(pdata->reset_gpio_port[1], 1);
> }
>
> - ret = usb_add_hcd(hcd, irq, IRQF_SHARED);
> - if (ret) {
> - dev_err(dev, "failed to add hcd with err %d\n", ret);
> - goto err_add_hcd;
> - }
> -
> /* root ports should always stay powered */
> ehci_port_power(omap_ehci, 1);
>
> --
> 1.7.10.4
>
Hi Samuel
I have validated this patch v3 in omap3 beagle XM .
Acked-by: Keshava Munegowda <keshava_mgowda at ti.com>
Tested-by: Keshava Munegowda <keshava_mgowda at ti.com>
regards
keshava
More information about the linux-arm-kernel
mailing list