[PATCH 9/9] Kirkwood: Add basic device tree support for QNAP TS219.
Jason Cooper
jason at lakedaemon.net
Sun Jun 10 13:23:13 EDT 2012
On Sun, Jun 10, 2012 at 12:32:01PM +0200, Andrew Lunn wrote:
> The two different variants of QNAP TS devices, varying by SoC, put the
> GPIO keys on different GPIO lines. Hence we need two different DT
> board descriptions, which share the same board-ts219.c file.
>
> Signed-off-by: Andrew Lunn <andrew at lunn.ch>
> ---
> arch/arm/boot/dts/kirkwood-ts219-6281.dts | 21 +++++++
> arch/arm/boot/dts/kirkwood-ts219-6282.dts | 21 +++++++
> arch/arm/boot/dts/kirkwood-ts219.dtsi | 73 ++++++++++++++++++++++++
> arch/arm/mach-kirkwood/Kconfig | 15 +++++
> arch/arm/mach-kirkwood/Makefile | 1 +
> arch/arm/mach-kirkwood/Makefile.boot | 1 +
> arch/arm/mach-kirkwood/board-dt.c | 4 ++
> arch/arm/mach-kirkwood/board-ts219.c | 86 +++++++++++++++++++++++++++++
> arch/arm/mach-kirkwood/common.h | 5 ++
> 9 files changed, 227 insertions(+)
> create mode 100644 arch/arm/boot/dts/kirkwood-ts219-6281.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ts219-6282.dts
> create mode 100644 arch/arm/boot/dts/kirkwood-ts219.dtsi
> create mode 100644 arch/arm/mach-kirkwood/board-ts219.c
>
> diff --git a/arch/arm/boot/dts/kirkwood-ts219-6281.dts b/arch/arm/boot/dts/kirkwood-ts219-6281.dts
> new file mode 100644
> index 0000000..ccbf327
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ts219-6281.dts
> @@ -0,0 +1,21 @@
> +/dts-v1/;
> +
> +/include/ "kirkwood-ts219.dtsi"
> +
> +/ {
> + gpio_keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + button at 1 {
> + label = "USB Copy";
> + linux,code = <133>;
> + gpios = <&gpio0 15 1>;
> + };
> + button at 2 {
> + label = "Reset";
> + linux,code = <0x198>;
> + gpios = <&gpio0 16 1>;
> + };
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/kirkwood-ts219-6282.dts b/arch/arm/boot/dts/kirkwood-ts219-6282.dts
> new file mode 100644
> index 0000000..fbe9932
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ts219-6282.dts
> @@ -0,0 +1,21 @@
> +/dts-v1/;
> +
> +/include/ "kirkwood-ts219.dtsi"
> +
> +/ {
> + gpio_keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + button at 1 {
> + label = "USB Copy";
> + linux,code = <133>;
> + gpios = <&gpio1 11 1>;
> + };
> + button at 2 {
> + label = "Reset";
> + linux,code = <0x198>;
> + gpios = <&gpio1 5 1>;
> + };
> + };
> +};
> \ No newline at end of file
> diff --git a/arch/arm/boot/dts/kirkwood-ts219.dtsi b/arch/arm/boot/dts/kirkwood-ts219.dtsi
> new file mode 100644
> index 0000000..e0520c3
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-ts219.dtsi
> @@ -0,0 +1,73 @@
> +/include/ "kirkwood.dtsi"
> +
> +/ {
> + model = "QNAP TS219 family";
> + compatible = "qnap,ts219", "mrvl,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x20000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + ocp at f1000000 {
> + i2c at 11000 {
> + status = "okay";
> +
> + s35390a: s35390a at 30 {
> + compatible = "s35390a";
> + reg = <0x30>;
> + };
> + };
> + serial at 12000 {
> + clock-frequency = <200000000>;
> + status = "okay";
> + };
> + serial at 12100 {
> + clock-frequency = <200000000>;
> + status = "okay";
> + };
> + spi at 10600 {
> + status = "okay";
> +
> + m25p128 at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "m25p128";
> + reg = <0>;
> + spi-max-frequency = <20000000>;
> + mode = <0>;
> +
> + partition at 0000000 {
> + reg = <0x00000000 0x00080000>;
> + label = "U-Boot";
> + };
> +
> + partition at 00200000 {
> + reg = <0x00200000 0x00200000>;
> + label = "Kernel";
> + };
> +
> + partition at 00400000 {
> + reg = <0x00400000 0x00900000>;
> + label = "RootFS1";
> + };
> + partition at 00d00000 {
> + reg = <0x00d00000 0x00300000>;
> + label = "RootFS2";
> + };
> + partition at 00040000 {
> + reg = <0x00080000 0x00040000>;
> + label = "U-Boot Config";
> + };
> + partition at 000c0000 {
> + reg = <0x000c0000 0x00140000>;
> + label = "NAS Config";
> + };
> + };
> + };
> + };
> +};
> diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
> index 199764f..8c6a5cd 100644
> --- a/arch/arm/mach-kirkwood/Kconfig
> +++ b/arch/arm/mach-kirkwood/Kconfig
> @@ -47,6 +47,7 @@ config MACH_GURUPLUG
> config ARCH_KIRKWOOD_DT
> bool "Marvell Kirkwood Flattened Device Tree"
> select USE_OF
> + select SERIAL_OF_PLATFORM
Please remove as previously discussed. I'm in the process of updating
kirkwood_defconfig (it will include this). Thanks.
Other than that,
Acked-by: Jason Cooper <jason at lakedaemon.net>
thx,
Jason.
> help
> Say 'Y' here if you want your kernel to support the
> Marvell Kirkwood using flattened device tree.
> @@ -80,6 +81,20 @@ config MACH_IB62X0_DT
> RaidSonic IB-NAS6210 & IB-NAS6220 devices, using
> Flattened Device Tree.
>
> +config MACH_TS219_DT
> + bool "Device Tree for QNAP TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and TS-219P+ Turbo NAS"
> + select ARCH_KIRKWOOD_DT
> + select ARM_APPENDED_DTB
> + select ARM_ATAG_DTB_COMPAT
> + help
> + Say 'Y' here if you want your kernel to support the QNAP
> + TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and
> + TS-219P+ Turbo NAS devices using Fattened Device Tree.
> + There are two different Device Tree descriptions, depending
> + on if the device is based on an if the board uses the MV6281
> + or MV6282. If you have the wrong one, the buttons will not
> + work.
> +
> config MACH_TS219
> bool "QNAP TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and TS-219P+ Turbo NAS"
> help
> diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile
> index d2b0590..0468b23 100644
> --- a/arch/arm/mach-kirkwood/Makefile
> +++ b/arch/arm/mach-kirkwood/Makefile
> @@ -25,3 +25,4 @@ obj-$(CONFIG_MACH_DREAMPLUG_DT) += board-dreamplug.o
> obj-$(CONFIG_MACH_ICONNECT_DT) += board-iconnect.o
> obj-$(CONFIG_MACH_DLINK_KIRKWOOD_DT) += board-dnskw.o
> obj-$(CONFIG_MACH_IB62X0_DT) += board-ib62x0.o
> +obj-$(CONFIG_MACH_TS219_DT) += board-ts219.o
> diff --git a/arch/arm/mach-kirkwood/Makefile.boot b/arch/arm/mach-kirkwood/Makefile.boot
> index 02edbdf..4a1f66a 100644
> --- a/arch/arm/mach-kirkwood/Makefile.boot
> +++ b/arch/arm/mach-kirkwood/Makefile.boot
> @@ -7,3 +7,4 @@ dtb-$(CONFIG_MACH_DLINK_KIRKWOOD_DT) += kirkwood-dns320.dtb
> dtb-$(CONFIG_MACH_DLINK_KIRKWOOD_DT) += kirkwood-dns325.dtb
> dtb-$(CONFIG_MACH_ICONNECT_DT) += kirkwood-iconnect.dtb
> dtb-$(CONFIG_MACH_IB62X0_DT) += kirkwood-ib62x0.dtb
> +dtb-$(CONFIG_MACH_TS219_DT) += kirkwood-qnap-ts219.dtb
> diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c
> index 5aa025d..5dfdfc3 100644
> --- a/arch/arm/mach-kirkwood/board-dt.c
> +++ b/arch/arm/mach-kirkwood/board-dt.c
> @@ -76,6 +76,9 @@ static void __init kirkwood_dt_init(void)
> if (of_machine_is_compatible("raidsonic,ib-nas62x0"))
> ib62x0_init();
>
> + if (of_machine_is_compatible("qnap,ts219"))
> + qnap_dt_ts219_init();
> +
> of_platform_populate(NULL, kirkwood_dt_match_table,
> kirkwood_auxdata_lookup, NULL);
> }
> @@ -86,6 +89,7 @@ static const char *kirkwood_dt_board_compat[] = {
> "dlink,dns-325",
> "iom,iconnect",
> "raidsonic,ib-nas62x0",
> + "qnap,ts219",
> NULL
> };
>
> diff --git a/arch/arm/mach-kirkwood/board-ts219.c b/arch/arm/mach-kirkwood/board-ts219.c
> new file mode 100644
> index 0000000..0a70b77
> --- /dev/null
> +++ b/arch/arm/mach-kirkwood/board-ts219.c
> @@ -0,0 +1,86 @@
> +/*
> + *
> + * QNAP TS-11x/TS-21x Turbo NAS Board Setup via DT
> + *
> + * Copyright (C) 2012 Andrew Lunn <andrew at lunn.ch>
> + *
> + * Based on the board file ts219-setup.c:
> + *
> + * Copyright (C) 2009 Martin Michlmayr <tbm at cyrius.com>
> + * Copyright (C) 2008 Byron Bradley <byron.bbradley at gmail.com>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * as published by the Free Software Foundation; either version
> + * 2 of the License, or (at your option) any later version.
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/init.h>
> +#include <linux/platform_device.h>
> +#include <linux/mv643xx_eth.h>
> +#include <linux/ata_platform.h>
> +#include <linux/gpio_keys.h>
> +#include <linux/input.h>
> +#include <asm/mach-types.h>
> +#include <asm/mach/arch.h>
> +#include <mach/kirkwood.h>
> +#include "common.h"
> +#include "mpp.h"
> +#include "tsx1x-common.h"
> +
> +static struct mv643xx_eth_platform_data qnap_ts219_ge00_data = {
> + .phy_addr = MV643XX_ETH_PHY_ADDR(8),
> +};
> +
> +static struct mv_sata_platform_data qnap_ts219_sata_data = {
> + .n_ports = 2,
> +};
> +
> +static unsigned int qnap_ts219_mpp_config[] __initdata = {
> + MPP0_SPI_SCn,
> + MPP1_SPI_MOSI,
> + MPP2_SPI_SCK,
> + MPP3_SPI_MISO,
> + MPP4_SATA1_ACTn,
> + MPP5_SATA0_ACTn,
> + MPP8_TW0_SDA,
> + MPP9_TW0_SCK,
> + MPP10_UART0_TXD,
> + MPP11_UART0_RXD,
> + MPP13_UART1_TXD, /* PIC controller */
> + MPP14_UART1_RXD, /* PIC controller */
> + MPP15_GPIO, /* USB Copy button (on devices with 88F6281) */
> + MPP16_GPIO, /* Reset button (on devices with 88F6281) */
> + MPP36_GPIO, /* RAM: 0: 256 MB, 1: 512 MB */
> + MPP37_GPIO, /* Reset button (on devices with 88F6282) */
> + MPP43_GPIO, /* USB Copy button (on devices with 88F6282) */
> + MPP44_GPIO, /* Board ID: 0: TS-11x, 1: TS-21x */
> + 0
> +};
> +
> +void __init qnap_dt_ts219_init(void)
> +{
> + u32 dev, rev;
> +
> + kirkwood_mpp_conf(qnap_ts219_mpp_config);
> +
> + kirkwood_pcie_id(&dev, &rev);
> + if (dev == MV88F6282_DEV_ID)
> + qnap_ts219_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
> +
> + kirkwood_ge00_init(&qnap_ts219_ge00_data);
> + kirkwood_sata_init(&qnap_ts219_sata_data);
> + kirkwood_ehci_init();
> +
> + pm_power_off = qnap_tsx1x_power_off;
> +}
> +
> +static int __init ts219_pci_init(void)
> +{
> + if (machine_is_ts219())
> + kirkwood_pcie_init(KW_PCIE0);
> +
> + return 0;
> +}
> +subsys_initcall(ts219_pci_init);
> diff --git a/arch/arm/mach-kirkwood/common.h b/arch/arm/mach-kirkwood/common.h
> index 9248fa2..e0c2324 100644
> --- a/arch/arm/mach-kirkwood/common.h
> +++ b/arch/arm/mach-kirkwood/common.h
> @@ -58,6 +58,11 @@ void dreamplug_init(void);
> #else
> static inline void dreamplug_init(void) {};
> #endif
> +#ifdef CONFIG_MACH_TS219_DT
> +void qnap_dt_ts219_init(void);
> +#else
> +static inline void qnap_dt_ts219_init(void) {};
> +#endif
>
> #ifdef CONFIG_MACH_DLINK_KIRKWOOD_DT
> void dnskw_init(void);
> --
> 1.7.10
>
More information about the linux-arm-kernel
mailing list