[PATCH v2 8/9] ARM: dts: refresh dts file for arch mmp

[Mitch Bradley]

On 6/5/2012 3:28 PM, Arnd Bergmann wrote:
> On Tuesday 05 June 2012, Chris Ball wrote:
>> Hi Haojian,
>>
>> On Fri, May 04 2012, Haojian Zhuang wrote:
>>> Append mmp2 and pxa910 dts files. Update PXA168 dts files for irq,
>>> timer, gpio components.
>>
>> The patch I'm replying to introduced a device tree for MMP2/Brownstone
>> in 3.5-rc1.  We're looking at adopting the MMP2 device tree for the OLPC
>> XO-1.75 board, and Mitch Bradley has some corrections to the device tree
>> format that we'd like to make, appended below.
>>
>> You can see all of the files Mitch mentions at:
>> http://dev.laptop.org/~wmb/mmp2-devicetree/
>>
>> Here's my proposal for what to do next:
>>   * First, you choose one of the two forms that Mitch links to.
>>     (Either "mmp2.dtsi" or "mmp2-flat.dtsi"; we have a weak preference
>>     for mmp2-flat.dtsi.)
>
> My preference would be towards mmp2.dtsi. I've recommended doing it
> that way to other people, too.

In most cases, I have found that exposing the full hierarchy is 
preferable.  For this specific SoC, which I have been working with for 
quite awhile now, I haven't found any instance where exposing the 
AXI/APB levels buys you anything.  The hierarchy just adds clutter.

That said, I don't feel strongly about it.

>
>
>> d) Moved the "intcmux" nodes down a level so they are children of the
>> top-level interrupt-controller node.  The problem with having them as
>> peers of the top-level interrupt-controller is that their "reg"
>> properties conflict.  For example:
>> intcmux4 at d4282150 { ... reg =<0x150 0x4>,<0x168 0x4>  ... }
>>
>> This is incorrect in several ways:
>>
>>     1) "@d4282150" is inconsistent with "reg =<0x150" .  The "unit
>>        address" after @ is supposed to be the same as the first component
>>        of the reg property.  d4282150 is not identical to 150.
>
> I thought the rule was that the @... part should be a translated address
> in the presence of "ranges" translation so we get a unique value in case
> we have multiple devices of the same name on the same address but on
> different buses.
>
> If we change this here, I suppose it also needs to be changed in a number
> of other places, and we have to rethink the method for unique device
> names.

My thinking was that "ranges" is inappropriate in this case (within the 
top-level interrupt controller node), and I got rid of it.  That being 
the case, this is not "in the presence of ranges".

>
>
>> The solution is to put the intcmux nodes underneath the
>> interrupt-controller node.  The interrupt-controller node now has
>> #address-cells and #size-cells properties so it can have children, but
>> it does not have a ranges property, so the address space is not passed
>> through.  The child (intcmux) reg addresses can then be interpreted
>> independently, without conflict.
>
> Right. The implication for this however is that the driver cannot
> treat the reg property as a physical address it can do ioremap on,
> but needs to interface with the driver that provides the address
> space.

Indeed.  For this driver, the intcmux subnodes are handled by the same 
driver as the top-level interrupt controller, and those subordinate 
registers are accessed via that driver's one mapping of the register block.


>
>
> 	Arnd
>