[RFC 05/24] ARM: omap: clk: Nuke plat clock.c & clock.h if CONFIG_COMMON_CLK

[Jon Hunter]

Hi Rajendra,

On 06/04/2012 11:58 PM, Rajendra Nayak wrote:
> Hi Jon,
> 
>> On 06/04/2012 09:16 AM, Rajendra Nayak wrote:
>>>
>>>>> +/* struct clksel_rate.flags possibilities */
>>>>> +#define RATE_IN_242X        (1<<   0)
>>>>> +#define RATE_IN_243X        (1<<   1)
>>>>> +#define RATE_IN_3430ES1        (1<<   2)    /* 3430ES1 rates only */
>>>>> +#define RATE_IN_3430ES2PLUS    (1<<   3)    /* 3430 ES>= 2 rates
>>>>> only */
>>>>> +#define RATE_IN_36XX        (1<<   4)
>>>>> +#define RATE_IN_4430        (1<<   5)
>>>>> +#define RATE_IN_TI816X        (1<<   6)
>>>>> +#define RATE_IN_4460        (1<<   7)
>>>>> +#define RATE_IN_AM33XX        (1<<   8)
>>>>> +#define RATE_IN_TI814X        (1<<   9)
>>>>> +
>>>>> +#define RATE_IN_24XX        (RATE_IN_242X | RATE_IN_243X)
>>>>> +#define RATE_IN_34XX        (RATE_IN_3430ES1 | RATE_IN_3430ES2PLUS)
>>>>> +#define RATE_IN_3XXX        (RATE_IN_34XX | RATE_IN_36XX)
>>>>> +#define RATE_IN_44XX        (RATE_IN_4430 | RATE_IN_4460)
>>>>> +
>>>>> +/* RATE_IN_3430ES2PLUS_36XX includes 34xx/35xx with ES>=2, and all
>>>>> 36xx/37xx */
>>>>> +#define RATE_IN_3430ES2PLUS_36XX    (RATE_IN_3430ES2PLUS |
>>>>> RATE_IN_36XX)
>>>>> +
>>>>> +/* Platform flags for the clkdev-OMAP integration code */
>>>>> +#define CK_242X        (1<<   4)
>>>>> +#define CK_243X        (1<<   5)        /* 243x, 253x */
>>>>> +#define CK_3430ES1    (1<<   6)        /* 34xxES1 only */
>>>>> +#define CK_3430ES2PLUS    (1<<   7)        /* 34xxES2, ES3,
>>>>> non-Sitara 35xx only */
>>>>> +#define CK_3505        (1<<   8)
>>>>> +#define CK_3517        (1<<   9)
>>>>> +#define CK_36XX        (1<<   10)       /* 36xx/37xx-specific
>>>>> clocks */
>>>>> +#define CK_443X        (1<<   11)
>>>>> +#define CK_TI816X    (1<<   12)
>>>>> +#define CK_446X        (1<<   13)
>>>>> +
>>>>> +#define CK_34XX        (CK_3430ES1 | CK_3430ES2PLUS)
>>>>> +#define CK_AM35XX    (CK_3505 | CK_3517)     /* all Sitara AM35xx */
>>>>> +#define CK_3XXX        (CK_34XX | CK_AM35XX | CK_36XX)
>>>>
>>>> I am not sure why we should duplicate these defines in an OMAP2
>>>> specific
>>>> header. What not just leave in plat clock.h where we have all the
>>>> RATE_IN_xxx and CK_xxx for all OMAP devices?
>>>
>>> These get removed from the file which is used for OMAP1 in a later
>>> patch. Like I said the idea was to separate out whats needed for OMAP1
>>> (using legacy struct clk) and OMAP2+ (using common struct clk) with
>>> both headers residing in respective mach-omap folders. (The RFC I posted
>>> still had the OMAP1 file in plat-omap)
>>
>> But these definitions are unrelated to whether you use common clock or
>> legacy. So why move them?
> 
> I am really fine either way, I don;t see a big issue in keeping these
> in plat clock.h and some others with ifdefs around for COMMON_CLK.
> The bigger issue is moving OMAP1 to common clk and I don't plan to do
> it as part of this series.

Ok, thanks. I guess ultimately it is Paul's decision but you know my
preference ;-)

As for omap1, I was not expecting you/we convert this at this point.
That is not my goal either. However, just to make sure that if and when
we do it will not be such a massive churn.

>>
>>>>
>>>>> +/**
>>>>> + * struct clksel_rate - register bitfield values corresponding to
>>>>> clk divisors
>>>>> + * @val: register bitfield value (shifted to bit 0)
>>>>> + * @div: clock divisor corresponding to @val
>>>>> + * @flags: (see "struct clksel_rate.flags possibilities" above)
>>>>> + *
>>>>> + * @val should match the value of a read from struct clk.clksel_reg
>>>>> + * AND'ed with struct clk.clksel_mask, shifted right to bit 0.
>>>>> + *
>>>>> + * @div is the divisor that should be applied to the parent clock's
>>>>> rate
>>>>> + * to produce the current clock's rate.
>>>>> + */
>>>>> +struct clksel_rate {
>>>>> +    u32    val;
>>>>> +    u8    div;
>>>>> +    u8    flags;
>>>>> +};
>>>>> +
>>>>> +/**
>>>>> + * struct clksel - available parent clocks, and a pointer to their
>>>>> divisors
>>>>> + * @parent: struct clk * to a possible parent clock
>>>>> + * @rates: available divisors for this parent clock
>>>>> + *
>>>>> + * A struct clksel is always associated with one or more struct clks
>>>>> + * and one or more struct clksel_rates.
>>>>> + */
>>>>> +struct clksel {
>>>>> +    struct clk            *parent;
>>>>> +    const struct clksel_rate    *rates;
>>>>> +};
>>>>
>>>> These above clksel structures would be need for omap1 devices so
>>>> that we
>>>> could use the clock framework to set the parent clock. So why not keep
>>>> in plat clock.h?
>>>
>>> We could, but that alone wouldn't be enough if we move OMAP2+ alone to
>>> common clk, it would mean we duplicate the clksel handling code too,
>>> and if we do that, maybe its not that bad to just duplicate a couple
>>> more struct definitions.
>>
>> So I have tested the legacy clksel code on omap1 and it works. So I
>> would hope that the common clock version of clksel would work too for
>> omap1 (if we move omap1 to the common clock framework).
> 
> Yes, *if we move omap1 to common clock* :-)

Agree :-)

Thanks
Jon