[PATCH v2 1/4] mmc: omap_hsmmc: Convert hsmmc driver to use device tree

Cousson, Benoit b-cousson at ti.com
Fri Feb 24 07:51:15 EST 2012


On 2/24/2012 12:35 PM, Rajendra Nayak wrote:
> On Friday 24 February 2012 05:02 PM, T Krishnamoorthy, Balaji wrote:
>> On Thu, Feb 23, 2012 at 5:31 PM, Rajendra Nayak<rnayak at ti.com> wrote:
>>> Define dt bindings for the ti-omap-hsmmc, and adapt
>>> the driver to extract data (which was earlier passed as
>>> platform_data) from device tree.
>>>
>>> Signed-off-by: Rajendra Nayak<rnayak at ti.com>
>>> ---
>>> .../devicetree/bindings/mmc/ti-omap-hsmmc.txt | 31 +++++++++
>>> drivers/mmc/host/omap_hsmmc.c | 68 ++++++++++++++++++++
>>> 2 files changed, 99 insertions(+), 0 deletions(-)
>>> create mode 100644
>>> Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
>>>
>>> diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
>>> b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
>>> new file mode 100644
>>> index 0000000..e4fa8f0
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
>>> @@ -0,0 +1,31 @@
>>> +* TI Highspeed MMC host controller for OMAP
>>> +
>>> +The Highspeed MMC Host Controller on TI OMAP family
>>> +provides an interface for MMC, SD, and SDIO types of memory cards.
>>> +
>>> +Required properties:
>>> +- compatible:
>>> + Should be "ti,omap2-hsmmc", for OMAP2/3 controllers
>>
>> omap_hsmmc is applicable for omap2430 and omap3.
>> omap2420 has non high speed controller mmci-omap -
>> drivers/mmc/host/omap.c
>> May be omap3-hsmmc compatible with omap2430 ?
>
> Agree. I think its best in that case for me to define a
> compatible "ti,omap2430-hsmmc" for omap2430 and "ti,omap3-hsmmc"
> for omap3. Though the IP blocks are same, I cant think of some
> common compatible string without causing confusion.

It depends, can we detect that using HW revision?
In that case, there is no need to differentiate again with compatible.

Regards,
Benoit

>
>>
>>> + Should be "ti,omap4-hsmmc", for OMAP4 controllers
>>> +- ti,hwmods: Must be "mmc<n>", n is controller instance starting 1
>>> +- reg : should contain hsmmc registers location and length
>>> +
>>> +Optional properties:
>>> +ti,dual-volt: boolean, supports dual voltage cards
>>> +<supply-name>-supply: phandle to the regulator device tree node
>>> +"supply-name" examples are "vmmc", "vmmc_aux" etc
>>> +ti,bus-width: Number of data lines, default assumed is 1 if the
>>> property is missing.
>>> +cd-gpios: GPIOs for card detection
>>> +wp-gpios: GPIOs for write protection
>>> +ti,non-removable: non-removable slot (like eMMC)
>>> +
>>> +Example:
>>> + mmc1: mmc at 0x4809c000 {
>>> + compatible = "ti,omap4-hsmmc";
>>> + reg =<0x4809c000 0x400>;
>>> + ti,hwmods = "mmc1";
>>> + ti,dual-volt;
>>> + ti,bus-width =<4>;
>>> + vmmc-supply =<&vmmc>; /* phandle to regulator node */
>>> + ti,non-removable;
>>> + };
>
> _______________________________________________
> devicetree-discuss mailing list
> devicetree-discuss at lists.ozlabs.org
> https://lists.ozlabs.org/listinfo/devicetree-discuss




More information about the linux-arm-kernel mailing list