[PATCH v2] ARM: OMAP2+: gpmc-smsc911x: add required smsc911x regulators
Matt Porter
mporter at ti.com
Wed Feb 22 11:45:03 EST 2012
This fixes smsc911x support on platforms using gpmc_smsc911x_init().
Commit c7e963f6888816 (net/smsc911x: Add regulator support) added
the requirement that platforms provide vdd33a and vddvario supplies.
Signed-off-by: Matt Porter <mporter at ti.com>
---
Changes for v2:
- temporary fix to avoid platform device id conflicts
- add commit summary from the smsc911x regulator support commit
- incorporate platform device registration error cause reporting
arch/arm/mach-omap2/gpmc-smsc911x.c | 54 ++++++++++++++++++++++++++++++++++-
1 files changed, 53 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-omap2/gpmc-smsc911x.c b/arch/arm/mach-omap2/gpmc-smsc911x.c
index 9970331..a7388ed 100644
--- a/arch/arm/mach-omap2/gpmc-smsc911x.c
+++ b/arch/arm/mach-omap2/gpmc-smsc911x.c
@@ -19,6 +19,8 @@
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/smsc911x.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
#include <plat/board.h>
#include <plat/gpmc.h>
@@ -42,6 +44,50 @@ static struct smsc911x_platform_config gpmc_smsc911x_config = {
.flags = SMSC911X_USE_16BIT,
};
+static struct regulator_consumer_supply gpmc_smsc911x_supply[] = {
+ REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
+ REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
+};
+
+/* Generic regulator definition to satisfy smsc911x */
+static struct regulator_init_data gpmc_smsc911x_reg_init_data = {
+ .constraints = {
+ .min_uV = 3300000,
+ .max_uV = 3300000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(gpmc_smsc911x_supply),
+ .consumer_supplies = gpmc_smsc911x_supply,
+};
+
+static struct fixed_voltage_config gpmc_smsc911x_fixed_reg_data = {
+ .supply_name = "gpmc_smsc911x",
+ .microvolts = 3300000,
+ .gpio = -EINVAL,
+ .startup_delay = 0,
+ .enable_high = 0,
+ .enabled_at_boot = 1,
+ .init_data = &gpmc_smsc911x_reg_init_data,
+};
+
+/*
+ * Platform device id of 42 is a temporary fix to avoid conflicts
+ * with other reg-fixed-voltage devices. The real fix should
+ * involve the driver core providing a way of dynamically
+ * assigning a unique id on registration for platform devices
+ * in the same name space.
+ */
+static struct platform_device gpmc_smsc911x_regulator = {
+ .name = "reg-fixed-voltage",
+ .id = 42,
+ .dev = {
+ .platform_data = &gpmc_smsc911x_fixed_reg_data,
+ },
+};
+
/*
* Initialize smsc911x device connected to the GPMC. Note that we
* assume that pin multiplexing is done in the board-*.c file,
@@ -51,10 +97,16 @@ void __init gpmc_smsc911x_init(struct omap_smsc911x_platform_data *board_data)
{
struct platform_device *pdev;
unsigned long cs_mem_base;
- int ret;
+ int ret, err;
gpmc_cfg = board_data;
+ err = platform_device_register(&gpmc_smsc911x_regulator);
+ if (err < 0) {
+ pr_err("Unable to register smsc911x regulators: %d\n", err);
+ return;
+ }
+
if (gpmc_cs_request(gpmc_cfg->cs, SZ_16M, &cs_mem_base) < 0) {
pr_err("Failed to request GPMC mem region\n");
return;
--
1.7.5.4
More information about the linux-arm-kernel
mailing list