[PATCH 1/4 v2] i2c/gpio: add DT support

[Jean-Christophe PLAGNIOL-VILLARD]

On 13:58 Mon 20 Feb     , Russell King - ARM Linux wrote:
> On Mon, Feb 20, 2012 at 02:46:34PM +0100, Jean-Christophe PLAGNIOL-VILLARD wrote:
> > On 14:37 Mon 20 Feb     , Jean-Christophe PLAGNIOL-VILLARD wrote:
> > > On 12:50 Mon 20 Feb     , Russell King - ARM Linux wrote:
> > > > On Mon, Feb 20, 2012 at 11:22:31AM +0100, Jean-Christophe PLAGNIOL-VILLARD wrote:
> > > > > On 10:08 Mon 20 Feb     , Russell King - ARM Linux wrote:
> > > > > > On Mon, Feb 20, 2012 at 10:58:13AM +0100, Jean-Christophe PLAGNIOL-VILLARD wrote:
> > > > > > > On 18:17 Mon 13 Feb     , Karol Lewandowski wrote:
> > > > > > > > > +	- udelay: delay between GPIO operations (may depend on each platform)
> > > > > > > > > +	- timeout: timeout to get data (ms)
> > > > > > > > 
> > > > > > > > 
> > > > > > > > If these are really needed then I would prefer to have these fully
> > > > > > > > qualified (with unit type "-ms/-millisecs" appended).
> > > > > > > > 
> > > > > > > > Regulator framework, with its "-microvolt/-microamp", serve here as
> > > > > > > > prime example of being quite descriptive (one doesn't neet to look up
> > > > > > > > the docs). Please see:
> > > > > > > > 
> > > > > > > >   http://permalink.gmane.org/gmane.linux.ports.arm.omap/67637
> > > > > > > timeout are usualy in ms I don't really see the need of -ms or so
> > > > > > 
> > > > > > Which is obviously total crap for udelay, which would be in _micro_seconds.
> > > > > agreed but here on i2c gpio I never see timetout as udelay so I don't see
> > > > > the mandatory to force the name in the binding
> > > > > 
> > > > > futhermore it's maybe linux specific
> > > > 
> > > > Stop grabbing at straws.  There's nothing linux specific about the units
> > > > of specification.
> > > > 
> > > > What is linux specific is specifying the _delay_ rather than specifying
> > > > the bus frequency.  So as soon as you're trying to justify not adding
> > > > the units because they may be linux specific, you've already lost that
> > > > argument by using a delay rather than a bus frequency.  You can't have
> > > > it both ways.
> > > > 
> > > > Moreover, mixing microseconds and milliseconds in the properties for a
> > > > device is absolutely insane.
> > > > 
> > > > So, which ever way, your patch as it currently stands is wrong and broken.
> > >  no what I said is the binding timeout is maybe linux specific for i2c gpio
> > 
> > I do not argue about that here we do not even disucss about the bus frequency
> > but the specific bining to the i2c algo bit for it's internal timeout
> > 
> > the timeout is used to do not end in an infinite loop while ready the scl on
> > slow device
> 
> The patch is still wrong and broken.
> 
> As you're not listening to me at all, I've lost patience, so I'm just going
> to say this:
> 
> Explicit NAK on this patch.
> 
> When you feel like you can _constructively_ _consider_ the point that both
> Karol and myself have raised with respect to the _U_N_I_T_S_ then feel free
> to continue this discussion.  If not, don't waste your time writing another
> email.  I hope that's plain.
I do not discuss about the U_N_I_T_S at all in this reply
so the NACK is no revelent

I just said here the bind for the "timeout" is maybe linux specific which means
need to be prefixed by "linux,"

so you discuss about timing again when I explain the binding named "timeout"
meaming

Best Regards,
J.