[PATCH 13/18] ARM: at91/rtc-at91sam9: pass the GPBR to use via ressources

Jean-Christophe PLAGNIOL-VILLARD plagnioj at jcrosoft.com
Sun Feb 19 20:20:10 EST 2012


On 11:43 Mon 20 Feb     , Ryan Mallon wrote:
> On 18/02/12 04:50, Nicolas Ferre wrote:
> 
> > From: Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
> > 
> > The GPBR registers are used for storing RTC values. The GPBR registers
> > to use are now provided using standard resource entry. The array is
> > filled in SoC specific code.
> > rtc-at91sam9 RTT as RTC driver is modified to retrieve this information.
> > 
> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
> > Acked-by: Nicolas Ferre <nicolas.ferre at atmel.com>
> > ---
> >  arch/arm/mach-at91/at91sam9260_devices.c      |   10 +++++++-
> >  arch/arm/mach-at91/at91sam9261_devices.c      |    8 ++++++-
> >  arch/arm/mach-at91/at91sam9263_devices.c      |   16 +++++++++++--
> >  arch/arm/mach-at91/at91sam9g45_devices.c      |    8 ++++++-
> >  arch/arm/mach-at91/at91sam9rl_devices.c       |    8 ++++++-
> >  arch/arm/mach-at91/include/mach/at91sam9260.h |    5 +--
> >  arch/arm/mach-at91/include/mach/at91sam9261.h |    5 +--
> >  arch/arm/mach-at91/include/mach/at91sam9263.h |    5 +--
> >  arch/arm/mach-at91/include/mach/at91sam9g45.h |    5 +--
> >  arch/arm/mach-at91/include/mach/at91sam9rl.h  |    2 +-
> >  drivers/rtc/rtc-at91sam9.c                    |   29 +++++++++++++++++++++---
> >  11 files changed, 76 insertions(+), 25 deletions(-)
> > 
> > diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c
> > index 2071017..ae2b648 100644
> > --- a/arch/arm/mach-at91/at91sam9260_devices.c
> > +++ b/arch/arm/mach-at91/at91sam9260_devices.c
> > @@ -718,14 +718,16 @@ static struct resource rtt_resources[] = {
> >  		.start	= AT91SAM9260_BASE_RTT,
> >  		.end	= AT91SAM9260_BASE_RTT + SZ_16 - 1,
> >  		.flags	= IORESOURCE_MEM,
> > -	}
> > +	}, {
> > +		.flags	= IORESOURCE_MEM,
> > +	},
> >  };
> >  
> >  static struct platform_device at91sam9260_rtt_device = {
> >  	.name		= "at91_rtt",
> >  	.id		= 0,
> >  	.resource	= rtt_resources,
> > -	.num_resources	= ARRAY_SIZE(rtt_resources),
> > +	.num_resources	= 1,
> 
> 
> Why this change? The device has two resources, and the rtc driver
> request both of them, so why are you saying there is only one resource
> here. It either needs to be changed back to use ARRAY_SIZE, or needs a
> comment explaining what magic is in use.
because the number of resources depends on the user of rtt
we must not hardcode the GPBR reg as this resource will be present only if the
rtc-at91sam9 is enabled

> 
> <snip>
> 
> >  #if IS_ENABLED(CONFIG_RTC_DRV_AT91SAM9)
> >  static void __init at91_add_device_rtt_rtc(void)
> >  {
> >  	struct platform_device *pdev;
> > +	struct resource *r;
> >  
> >  	switch (CONFIG_RTC_DRV_AT91SAM9_RTT) {
> >  	case 0:
> >  		pdev = &at91sam9263_rtt0_device;
> > +		r = rtt0_resources;
> >  		break;
> >  	case 1:
> >  		pdev = &at91sam9263_rtt1_device;
> > +		r = rtt1_resources;
> >  		break;
> >  	default:
> >  		pr_err("at91sam9263: support only 2 RTT (%d)\n",
> > -			 CONFIG_RTC_DRV_AT91SAM9_RTT);
> > +		       CONFIG_RTC_DRV_AT91SAM9_RTT);
> >  		return;
> >  	}
> 
> >  
> > +	r[1].start = AT91SAM9263_BASE_GPBR + 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
> > +	r[1].end = r[1].start + 3;
> >  	pdev->name = "rtc-at91sam9";
> > +	pdev->num_resources++;
> 
> 
> Okay, makes a little more sense now. I really think it needs a comment
> explaining how the resources are being managed, since it is a bit
> non-obvious.
> 
> Also, can only one of the RTT's can be used as an RTC at a time?
it was always the case as nearly all soc have only one rtt and via Kconfig
doc in Kconfig

Best Regards,
J.

> 
> ~Ryan



More information about the linux-arm-kernel mailing list