[BUG] genirq: Race condition in ONESHOT IRQ handler disabling IRQ forever
Lars-Peter Clausen
lars at metafoo.de
Tue Feb 7 08:07:22 EST 2012
On 02/07/2012 01:52 PM, Lothar Waßmann wrote:
> Hi,
>
> Yong Zhang writes:
>> On Tue, Feb 07, 2012 at 11:01:06AM +0100, Lothar Waßmann wrote:
>>> Hi,
>>>
>>>> On Mon, Feb 06, 2012 at 09:14:47AM +0100, Lothar Waßmann wrote:
>>>>> Hi,
>>>>>
>>>>> I already sent this to <linux-kernel at vger.kernel.org> on Feb. 1, 2012
>>>>> but did not get any response there. So resending to a wider audience
>>>>> with improved subject line:
>>>>>
>>>>> there is a race condition in the threaded IRQ handler code for oneshot
>>>>> interrupts that may lead to disabling an IRQ indefinitely. IRQs are
>>>>> masked before calling the hard-irq handler and are unmasked only after
>>>>> the soft-irq handler has been run. Thus if the hard-irq handler
>>>>> returns IRQ_HANDLED instead of IRQ_WAKE_THREAD, meaning the soft-irq
>>>>> will not be called, the interrupt will remain masked forever.
>>>>>
>>>>> This can happen due to a short pulse on the interrupt line, that
>>>>> triggers the interrupt logic, but goes undetected by the hard-irq
>>>>> handler. The problem can be reproduced with the TSC2007 touch
>>>>> controller driver that uses ONESHOT interrupts.
>>>>
>>>> Isn't it the responsibility of the driver (say TSC2007)?
>>>>
>>>> In this case, TSC2007 should return IRQ_WAKE_THREAD IMHO.
>>>>
>>> That would mean it had to return IRQ_WAKE_THREAD unconditionally
>>> making the return code useless.
>>> And it would cause an extra useless loop through the softirq
>>> handler.
>>
>> Yeah, it's the default behavior when we introduce 'theadirqs',
>> and it's safe.
>>
> So, the correct solution would be to remove the check for
> IRQ_WAKE_THREAD in handle_irq_event_percpu() and always invoke the
> softirq handler?
> Note that this problem is not specific to the TSC2007 driver, but may
> occur with any hardware.
>
> Or maybe do the unmasking in handle_irq_event() as proposed by
> Lars-Peter Clausen in <4F2FAE93.5020205 at metafoo.de>?
> Like that:
> diff --git a/kernel/irq/chip.c b/kernel/irq/chip.c
> index f7c543a..fbf68c7 100644
> --- a/kernel/irq/chip.c
> +++ b/kernel/irq/chip.c
> @@ -343,6 +343,8 @@ EXPORT_SYMBOL_GPL(handle_simple_irq);
> void
> handle_level_irq(unsigned int irq, struct irq_desc *desc)
> {
> + int ret;
This should be irqreturn_t
> +
> raw_spin_lock(&desc->lock);
> mask_ack_irq(desc);
>
> @@ -360,10 +362,12 @@ handle_level_irq(unsigned int irq, struct irq_desc *desc)
> if (unlikely(!desc->action || irqd_irq_disabled(&desc->irq_data)))
> goto out_unlock;
>
> - handle_irq_event(desc);
> + ret = handle_irq_event(desc);
>
> - if (!irqd_irq_disabled(&desc->irq_data) && !(desc->istate & IRQS_ONESHOT))
> + if (!irqd_irq_disabled(&desc->irq_data) &&
> + (!(desc->istate & IRQS_ONESHOT) || ret != IRQ_WAKE_THREAD))
As I said, check for the bit, not for the value. This will ensure that will
also work with shared interrupts. So something like this:
!((desc->istate & IRQS_ONESHOT) && (ret & IRQ_WAKE_THREAD)))
> unmask_irq(desc);
> +
> out_unlock:
> raw_spin_unlock(&desc->lock);
> }
>
>
> Lothar Waßmann
More information about the linux-arm-kernel
mailing list