[PATCH v9 01/25] gpio/omap: remove dependency on gpio_bank_count

[Varadarajan, Charulatha]

Felipe,

On Sun, Feb 5, 2012 at 14:38, Felipe Balbi <balbi at ti.com> wrote:
> Hi,
>
> On Sun, Feb 05, 2012 at 12:37:55PM +0530, Varadarajan, Charulatha wrote:
>> Felipe,
>>
>> On Sat, Feb 4, 2012 at 21:38, Felipe Balbi <balbi at ti.com> wrote:
>> >
>> > Hi,
>> >
>> > On Fri, Feb 03, 2012 at 09:50:19AM -0800, Kevin Hilman wrote:
>> > > Felipe Balbi <balbi at ti.com> writes:
>> > >
>> > > [...]
>> > >
>> > > >> >This question remains. Why do we need those funtions ?
>> > > >>
>> > > >> These functions are called from the CPUIdle path so outside the scope
>> > > >> of the GPIO driver. These are part of a bunch of nasty PM hacks we
>> > > >> are doing in the CPU idle loop. We are in the process of getting rid
>> > > >> of most of them, but it looks like some are still needed.
>> > > >
>> > > > Too bad. I can see that the gpio pm implementation seems a bit
>> > > > "peculiar". I mean, pm does reference counting and yet the driver has
>> > > > checks to prevent multiple gets and puts on a single bank (meaning that
>> > > > pm counter will be either 0 or 1 at any point in time).
>> > > >
>> > > > To me it looks like those functions are there in order to forcefully put
>> > > > PER power domain in OFF because drivers are always holding a reference
>> > > > to their gpios (drivers generally gpio_request() on probe() and
>> > > > gpio_free() on remove()).
>> > > >
>> > > > Looks like the entire pm implementation on OMAP gpio driver has always
>> > > > considered only the fact that gpios can be requested and freed, but
>> > > > never that we want the system to go to OFF even while gpios are
>> > > > requested, because we have I/O PAD wakeups. At some point that has to be
>> > > > sorted out because that HACK is quite ugly :-)
>> > > >
>> > > > I'll see if I find some time to go over the interactions between
>> > > > gpio-omap.c and pm24x.c and pm34xx.c any of these days, but I can't
>> > > > promise anything ;-)
>> > >
>> > > If you look at the state of these prepare/resume hacks at the end of
>> > > this series, you'll see that they are significantly cleaner and do
>> > > nothing but call the runtime PM hooks.
>> >
>> > sure, definitely.
>> >
>> > > We have explored several ways to get rid of them completely in the idle
>> > > path but have not yet come up with a clean way, but this series gets us
>> > > a long ways towards that goal.
>> >
>> > have you thought about being a bit more aggressive at when to
>> > runtime_get and runtime_put ?
>> >
>> > I didn't test below (will do probably on monday), but I think this will
>> > help keeping GPIO block always suspended, and only wake it up when truly
>> > needed. That way, you could, at some point, remove that list_head
>> > because by the time you reach CPUIdle path, GPIO module is already
>> > suspended. That's the theory at least, gotta run it first on silicon to
>> > be sure
>> >
>> > diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
>> > index 4273401..2dd9ced 100644
>> > --- a/drivers/gpio/gpio-omap.c
>> > +++ b/drivers/gpio/gpio-omap.c
>> > @@ -537,12 +537,7 @@ static int omap_gpio_request(struct gpio_chip *chip, unsigned offset)
>> >        struct gpio_bank *bank = container_of(chip, struct gpio_bank, chip);
>> >        unsigned long flags;
>> >
>> > -       /*
>> > -        * If this is the first gpio_request for the bank,
>> > -        * enable the bank module.
>> > -        */
>> > -       if (!bank->mod_usage)
>> > -               pm_runtime_get_sync(bank->dev);
>> > +       pm_runtime_get_sync(bank->dev);
>>
>> bank->mod_usage check is used to take care of doing pm_runtime_get*/put* only
>> if all the GPIOs in a particular bank are enabled or disabled respectively.
>
> and why should you care about that ? The first get will enable the
> resources you need, the second get will just increase a counter and so
> on. So if you have 32 gets, you will disable the module when you have 32
> puts.

Agreed!

-V Charulatha

>
>> With the above change, pm_runtime_put*/get* would be called for every
>> gpio_request()
>> /_free() (that is, for upto 32 pins in OMAP3/4) in a bank irrespective
>> of whether other
>
> so ?
>
>> GPIO pins are enabled or disabled in the same bank. Hence it is
>> required to have a
>> check based on mod_usage.
>
> unnecessary.
>
> --
> balbi