[PATCH v5] I2C: add CSR SiRFprimaII on-chip I2C controllers driver

Wolfram Sang ninja at nekote.pengutronix.de
Sun Feb 5 17:37:58 EST 2012


Hi,
On Sun, Jan 29, 2012 at 10:17:48PM +0800, Barry Song wrote:
> From: Zhiwu Song <Zhiwu.Song at csr.com>
> 
> SiRFprimaII is the latest generation application processor from CSR’s
> multi-function SoC product family.
> The SoC support codes are in arch/arm/mach-prima2 from Linux mainline
> 3.0.
> There are two I2C controllers on primaII, features include:
> * Two I2C controller modules are on chip
> * RISC I/O bus read write register
> * Up to 16 bytes data buffer for issuing commands and writing data
>   at the same time
> * Up to 16 commands, and receiving read data 16 bytes at a time
> * Error INT report (ACK check)
> * No-ACK bus protocols (SCCB bus protocols)
> 
> Signed-off-by: Zhiwu Song <Zhiwu.Song at csr.com>
> Signed-off-by: Xiangzhen Ye <Xiangzhen.Ye at csr.com>
> Signed-off-by: Yuping Luo <Yuping.Luo at csr.com>
> Signed-off-by: Barry Song <Baohua.Song at csr.com>

Thanks for your contribution! Is there a free datasheet for this controller
available?

> ---
>  -v5: don't disable already disabled clock as pointed out by Russell
> 
>  drivers/i2c/busses/Kconfig    |   10 +
>  drivers/i2c/busses/Makefile   |    1 +
>  drivers/i2c/busses/i2c-sirf.c |  439 +++++++++++++++++++++++++++++++++++++++++
>  drivers/i2c/busses/i2c-sirf.h |   61 ++++++
>  4 files changed, 511 insertions(+), 0 deletions(-)
>  create mode 100644 drivers/i2c/busses/i2c-sirf.c
>  create mode 100644 drivers/i2c/busses/i2c-sirf.h
> 
> diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
> index 3101dd5..a3c43fc 100644
> --- a/drivers/i2c/busses/Kconfig
> +++ b/drivers/i2c/busses/Kconfig
> @@ -618,6 +618,16 @@ config I2C_SH_MOBILE
>  	  This driver can also be built as a module.  If so, the module
>  	  will be called i2c-sh_mobile.
>  
> +config I2C_SIRF
> +	tristate "CSR SiRFprimaII I2C interface"
> +	depends on ARCH_PRIMA2
> +	help
> +	  If you say yes to this option, support will be included for the
> +	  CSR SiRFprimaII I2C interface.
> +
> +	  This driver can also be built as a module.  If so, the module
> +	  will be called i2c-sirf.
> +

Sorting is broken, same with Makefile.

>  config I2C_SIMTEC
>  	tristate "Simtec Generic I2C interface"
>  	select I2C_ALGOBIT
> diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
> index fba6da6..c30db66 100644
> --- a/drivers/i2c/busses/Makefile
> +++ b/drivers/i2c/busses/Makefile
> @@ -62,6 +62,7 @@ obj-$(CONFIG_I2C_S3C2410)	+= i2c-s3c2410.o
>  obj-$(CONFIG_I2C_S6000)		+= i2c-s6000.o
>  obj-$(CONFIG_I2C_SH7760)	+= i2c-sh7760.o
>  obj-$(CONFIG_I2C_SH_MOBILE)	+= i2c-sh_mobile.o
> +obj-$(CONFIG_I2C_SIRF)		+= i2c-sirf.o
>  obj-$(CONFIG_I2C_SIMTEC)	+= i2c-simtec.o
>  obj-$(CONFIG_I2C_STU300)	+= i2c-stu300.o
>  obj-$(CONFIG_I2C_TEGRA)		+= i2c-tegra.o
> diff --git a/drivers/i2c/busses/i2c-sirf.c b/drivers/i2c/busses/i2c-sirf.c
> new file mode 100644
> index 0000000..6432d35
> --- /dev/null
> +++ b/drivers/i2c/busses/i2c-sirf.c
> @@ -0,0 +1,439 @@
> +/*
> + * I2C bus driver for CSR SiRFprimaII
> + *
> + * Copyright (c) 2011 Cambridge Silicon Radio Limited, a CSR plc group company.
> + *
> + * Licensed under GPLv2 or later.
> + */
> +
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/slab.h>
> +#include <linux/platform_device.h>
> +#include <linux/i2c.h>
> +#include <linux/clk.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +
> +#include "i2c-sirf.h"
> +
> +#define SIRFSOC_I2C_DEFAULT_SPEED  100000
> +
> +struct sirfsoc_i2c {
> +	void __iomem *base;
> +	struct clk *clk;
> +	unsigned long speed;	/* I2C SCL frequency */
> +	int irq;

Do you really need those two?

> +	u32 cmd_ptr;		/* Current position in CMD buffer */
> +	u8 *buf;		/* Buffer passed by user */
> +	u32 msg_len;		/* Message length */
> +	u32 finished_len;	/* number of bytes read/written */
> +	u32 read_cmd_len;	/* number of read cmd sent */
> +	int msg_read;		/* 1 indicates a read message */
> +	int err_status;		/* 1 indicates an error on bus */
> +
> +	u32 sda_delay;		/* For suspend/resume */
> +	u32 clk_div;
> +	int last;		/* Last message in transfer, STOP cmd can be sent */
> +
> +	struct completion done;	/* indicates completion of message transfer */
> +	struct i2c_adapter *adapter;

Why a pointer and not the struct itself?

> +};
> +
> +static void i2c_sirfsoc_read_data(struct sirfsoc_i2c *siic)
> +{
> +	u32 data = 0;
> +	int i = 0;

i doesn't need to be initialized. data neither, but compilers fail on that sometimes.

> +
> +	for (i = 0; i < siic->read_cmd_len; i++) {
> +		if (!(i & 0x3))
> +			data = readl(siic->base + SIRFSOC_I2C_DATA_BUF + i);
> +		siic->buf[siic->finished_len++] =
> +			(unsigned char)((data & SIRFSOC_I2C_DATA_MASK(i)) >>
> +				SIRFSOC_I2C_DATA_SHIFT(i));

buf is declared u8.

> +
> +		BUG_ON(siic->finished_len > siic->msg_len);

BUG? Can't we handle this more gracefully?

> +	}
> +}
> +
> +static void i2c_sirfsoc_queue_cmd(struct sirfsoc_i2c *siic)
> +{
> +	u32 regval;
> +	int i = 0;
> +
> +	if (siic->msg_read) {
> +		while (((siic->finished_len + i) < siic->msg_len)
> +			&& (siic->cmd_ptr < SIRFSOC_I2C_CMD_BUF_MAX)) {

Either use a different indentation for the above line or add a newline below.
It is hard to see where the while() ends and the code block starts.

> +			regval = SIRFSOC_I2C_READ | SIRFSOC_I2C_CMD_RP(0);
> +			if (((siic->finished_len + i) ==
> +					(siic->msg_len - 1)) && siic->last)
> +				regval |= SIRFSOC_I2C_STOP | SIRFSOC_I2C_NACK;
> +			writel(regval,
> +				siic->base + SIRFSOC_I2C_CMD(siic->cmd_ptr++));
> +			i++;
> +		}
> +
> +		siic->read_cmd_len = i;
> +	} else {
> +		while ((siic->cmd_ptr < SIRFSOC_I2C_CMD_BUF_MAX - 1)
> +			&& (siic->finished_len < siic->msg_len)) {
> +			regval = SIRFSOC_I2C_WRITE | SIRFSOC_I2C_CMD_RP(0);
> +			if ((siic->finished_len == (siic->msg_len - 1))
> +				&& siic->last)
> +				regval |= SIRFSOC_I2C_STOP;
> +			writel(regval,
> +				siic->base + SIRFSOC_I2C_CMD(siic->cmd_ptr++));
> +			writel(siic->buf[siic->finished_len++],
> +				siic->base + SIRFSOC_I2C_CMD(siic->cmd_ptr++));
> +		}
> +	}
> +	siic->cmd_ptr = 0;
> +
> +	/* Trigger the transfer */
> +	writel(SIRFSOC_I2C_START_CMD, siic->base + SIRFSOC_I2C_CMD_START);
> +}
> +
> +static irqreturn_t i2c_sirfsoc_irq(int irq, void *dev_id)
> +{
> +	struct sirfsoc_i2c *siic = (struct sirfsoc_i2c *)dev_id;

No need to cast.

> +	u32 i2c_stat = readl(siic->base + SIRFSOC_I2C_STATUS);
> +
> +	if (i2c_stat & SIRFSOC_I2C_STAT_ERR) {
> +		/* Error conditions */
> +		siic->err_status = 1;
> +		writel(SIRFSOC_I2C_STAT_ERR, siic->base + SIRFSOC_I2C_STATUS);
> +
> +		if (i2c_stat & SIRFSOC_I2C_STAT_NACK)
> +			dev_err(&siic->adapter->dev, "ACK not received\n");
> +		else
> +			dev_err(&siic->adapter->dev, "I2C error\n");
> +
> +		complete(&siic->done);
> +	} else if (i2c_stat & SIRFSOC_I2C_STAT_CMD_DONE) {
> +		/* CMD buffer execution complete */
> +		if (siic->msg_read)
> +			i2c_sirfsoc_read_data(siic);
> +		if (siic->finished_len == siic->msg_len)
> +			complete(&siic->done);
> +		else /* Fill a new CMD buffer for left data */
> +			i2c_sirfsoc_queue_cmd(siic);
> +
> +		writel(SIRFSOC_I2C_STAT_CMD_DONE, siic->base + SIRFSOC_I2C_STATUS);
> +	}
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static void i2c_sirfsoc_set_address(struct sirfsoc_i2c *siic,
> +	struct i2c_msg *msg)
> +{
> +	unsigned char addr;
> +	u32 regval = SIRFSOC_I2C_START | SIRFSOC_I2C_CMD_RP(0) | SIRFSOC_I2C_WRITE;
> +
> +	/* no data and last message -> add STOP */
> +	if (siic->last && (msg->len == 0))
> +		regval |= SIRFSOC_I2C_STOP;
> +
> +	writel(regval, siic->base + SIRFSOC_I2C_CMD(siic->cmd_ptr++));
> +
> +	addr = msg->addr << 1;	/* Generate address */
> +	if (msg->flags & I2C_M_RD)
> +		addr |= 1;
> +	if (msg->flags & I2C_M_REV_DIR_ADDR)	/* Reverse direction bit */
> +		addr ^= 1;

You don't support MANGLING according to .functionality().

> +
> +	writel(addr, siic->base + SIRFSOC_I2C_CMD(siic->cmd_ptr++));
> +}
> +
> +static int i2c_sirfsoc_xfer_msg(struct sirfsoc_i2c *siic, struct i2c_msg *msg)
> +{
> +	u32 regval = readl(siic->base + SIRFSOC_I2C_CTRL);
> +	int timeout = (msg->len + 1) * 50;

That looks broken. What is 50 here?

> +	int ret = 0;
> +
> +	i2c_sirfsoc_set_address(siic, msg);
> +
> +	writel(regval | SIRFSOC_I2C_CMD_DONE_EN | SIRFSOC_I2C_ERR_INT_EN,
> +		siic->base + SIRFSOC_I2C_CTRL);
> +	i2c_sirfsoc_queue_cmd(siic);
> +
> +	if (wait_for_completion_timeout(&siic->done, timeout) == 0) {
> +		siic->err_status = 1;
> +		dev_err(&siic->adapter->dev, "Transfer timeout\n");
> +	}
> +
> +	writel(regval & ~(SIRFSOC_I2C_CMD_DONE_EN | SIRFSOC_I2C_ERR_INT_EN),
> +		siic->base + SIRFSOC_I2C_CTRL);
> +	writel(0, siic->base + SIRFSOC_I2C_CMD_START);
> +
> +	if (siic->err_status) {
> +		writel(readl(siic->base + SIRFSOC_I2C_CTRL) | SIRFSOC_I2C_RESET,
> +			siic->base + SIRFSOC_I2C_CTRL);
> +		while (readl(siic->base + SIRFSOC_I2C_CTRL) & SIRFSOC_I2C_RESET)
> +			cpu_relax();
> +
> +		ret = -EIO;
> +	}
> +
> +	return ret;
> +}
> +
> +static u32 i2c_sirfsoc_func(struct i2c_adapter *adap)
> +{
> +	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
> +}
> +
> +static int i2c_sirfsoc_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
> +	int num)
> +{
> +	struct sirfsoc_i2c *siic = adap->algo_data;
> +	int i, ret;
> +
> +	clk_enable(siic->clk);
> +
> +	for (i = 0; i < num; i++) {
> +		siic->buf = msgs[i].buf;
> +		siic->msg_len = msgs[i].len;
> +
> +		if (msgs[i].flags & I2C_M_RD)
> +			siic->msg_read = 1;
> +		else
> +			siic->msg_read = 0;

siic->msg_read = !!(flag & mask)?

> +
> +		siic->err_status = 0;
> +		siic->cmd_ptr = 0;
> +		siic->finished_len = 0;
> +		if (i == (num - 1))
> +			siic->last = 1;
> +		else
> +			siic->last = 0;
> +

siic->last = i == (num - 1)?

> +		ret = i2c_sirfsoc_xfer_msg(siic, &msgs[i]);
> +		if (ret) {
> +			clk_disable(siic->clk);
> +			return ret;
> +		}
> +	}
> +
> +	clk_disable(siic->clk);
> +	return num;
> +}
> +
> +/* I2C algorithms associated with this master controller driver */
> +static const struct i2c_algorithm i2c_sirfsoc_algo = {
> +	.master_xfer = i2c_sirfsoc_xfer,
> +	.functionality = i2c_sirfsoc_func,
> +};
> +
> +static int __devinit i2c_sirfsoc_probe(struct platform_device *pdev)
> +{
> +	struct sirfsoc_i2c *siic;
> +	struct i2c_adapter *new_adapter;
> +	struct resource *mem_res;
> +	struct clk *clk;
> +	int ctrl_speed;
> +
> +	int err;
> +	u32 regval;
> +
> +	clk = clk_get(&pdev->dev, NULL);
> +	if (IS_ERR(clk)) {
> +		err = PTR_ERR(clk);
> +		dev_err(&pdev->dev, "Clock get failed\n");
> +		goto err_get_clk;
> +	}
> +
> +	err = clk_prepare(clk);
> +	if (err) {
> +		dev_err(&pdev->dev, "Clock prepare failed\n");
> +		goto  err_clk_prep;

Double space. Not only here.

> +	}
> +
> +	err = clk_enable(clk);
> +	if (err) {
> +		dev_err(&pdev->dev, "Clock enable failed\n");
> +		goto  err_clk_en;
> +	}
> +
> +	ctrl_speed = clk_get_rate(clk);
> +
> +	new_adapter = devm_kzalloc(&pdev->dev, sizeof(*new_adapter), GFP_KERNEL);
> +	if (!new_adapter) {
> +		dev_err(&pdev->dev,
> +			"Can't allocate new i2c adapter!\n");
> +		err = -ENOMEM;
> +		goto out;
> +	}
> +
> +	siic = devm_kzalloc(&pdev->dev, sizeof(*siic), GFP_KERNEL);
> +	if (!siic) {
> +		dev_err(&pdev->dev, "Can't allocate driver data\n");
> +		err = -ENOMEM;
> +		goto out;
> +	}
> +	new_adapter->class = I2C_CLASS_HWMON | I2C_CLASS_DDC | I2C_CLASS_SPD;

Do you really need the class?

> +	siic->adapter = new_adapter;
> +
> +	mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	if (mem_res == NULL) {
> +		dev_err(&pdev->dev, "Unable to get MEM resource\n");
> +		err = -EINVAL;
> +		goto out;
> +	}
> +
> +	siic->base = devm_request_and_ioremap(&pdev->dev, mem_res);
> +	if (siic->base == NULL) {
> +		dev_err(&pdev->dev, "IO remap failed!\n");
> +		err = -ENOMEM;
> +		goto out;
> +	}
> +
> +	siic->irq = platform_get_irq(pdev, 0);
> +	if (siic->irq < 0) {
> +		err = -EINVAL;
> +		goto out;
> +	}

return the error code here?

> +	err = devm_request_irq(&pdev->dev, siic->irq, i2c_sirfsoc_irq, 0,
> +		dev_name(&pdev->dev), siic);
> +	if (err)
> +		goto out;
> +
> +	new_adapter->algo = &i2c_sirfsoc_algo;
> +	new_adapter->algo_data = siic;
> +
> +	new_adapter->dev.parent = &pdev->dev;
> +	new_adapter->nr = pdev->id;
> +
> +	strlcpy(new_adapter->name, "sirfsoc-i2c", sizeof(new_adapter->name));
> +
> +	platform_set_drvdata(pdev, new_adapter);
> +	init_completion(&siic->done);
> +
> +	/* Controller Initalisation */
> +
> +	writel(SIRFSOC_I2C_RESET, siic->base + SIRFSOC_I2C_CTRL);
> +	while (readl(siic->base + SIRFSOC_I2C_CTRL) & SIRFSOC_I2C_RESET)
> +		cpu_relax();
> +	writel(SIRFSOC_I2C_CORE_EN | SIRFSOC_I2C_MASTER_MODE,
> +		siic->base + SIRFSOC_I2C_CTRL);
> +
> +	siic->clk = clk;
> +	siic->speed = SIRFSOC_I2C_DEFAULT_SPEED;
> +	if (siic->speed < 100000)
> +		regval =
> +			(2 * ctrl_speed) / (2 * siic->speed * 11);
> +	else
> +		regval = ctrl_speed / (siic->speed * 5);
> +
> +	writel(regval, siic->base + SIRFSOC_I2C_CLK_CTRL);
> +	if (regval > 0xFF)
> +		writel(0xFF, siic->base + SIRFSOC_I2C_SDA_DELAY);
> +	else
> +		writel(regval, siic->base + SIRFSOC_I2C_SDA_DELAY);
> +
> +	err = i2c_add_numbered_adapter(new_adapter);
> +	if (err < 0) {
> +		dev_err(&pdev->dev, "Can't add new i2c adapter\n");
> +		goto out;
> +	}
> +
> +	clk_disable(clk);
> +
> +	dev_info(&pdev->dev, " I2C adapter ready to operate\n");
> +
> +	return 0;
> +
> +out:
> +	clk_disable(clk);
> +err_clk_en:
> +	clk_unprepare(clk);
> +err_clk_prep:
> +	clk_put(clk);
> +err_get_clk:
> +	return err;
> +}
> +
> +static int __devexit i2c_sirfsoc_remove(struct platform_device *pdev)
> +{
> +	struct i2c_adapter *adapter = platform_get_drvdata(pdev);
> +	struct sirfsoc_i2c *siic = adapter->algo_data;
> +
> +	writel(SIRFSOC_I2C_RESET, siic->base + SIRFSOC_I2C_CTRL);
> +	i2c_del_adapter(adapter);
> +	clk_unprepare(siic->clk);
> +	clk_put(siic->clk);
> +	return 0;
> +}
> +
> +#ifdef CONFIG_PM
> +static int i2c_sirfsoc_suspend(struct device *dev)
> +{
> +	struct platform_device *pdev = to_platform_device(dev);
> +	struct i2c_adapter *adapter = platform_get_drvdata(pdev);
> +	struct sirfsoc_i2c *siic = adapter->algo_data;
> +
> +	clk_enable(siic->clk);
> +	siic->sda_delay = readl(siic->base + SIRFSOC_I2C_SDA_DELAY);
> +	siic->clk_div = readl(siic->base + SIRFSOC_I2C_CLK_CTRL);
> +	clk_disable(siic->clk);
> +	return 0;
> +}
> +
> +static int i2c_sirfsoc_resume(struct device *dev)
> +{
> +	struct platform_device *pdev = to_platform_device(dev);
> +	struct i2c_adapter *adapter = platform_get_drvdata(pdev);
> +	struct sirfsoc_i2c *siic = adapter->algo_data;
> +
> +	clk_enable(siic->clk);
> +	writel(SIRFSOC_I2C_RESET, siic->base + SIRFSOC_I2C_CTRL);
> +	writel(SIRFSOC_I2C_CORE_EN | SIRFSOC_I2C_MASTER_MODE,
> +		siic->base + SIRFSOC_I2C_CTRL);
> +	writel(siic->clk_div, siic->base + SIRFSOC_I2C_CLK_CTRL);
> +	writel(siic->sda_delay, siic->base + SIRFSOC_I2C_SDA_DELAY);
> +	clk_disable(siic->clk);
> +	return 0;
> +}
> +
> +static const struct dev_pm_ops i2c_sirfsoc_pm_ops = {
> +	.suspend = i2c_sirfsoc_suspend,
> +	.resume = i2c_sirfsoc_resume,
> +};
> +#endif
> +
> +static const struct of_device_id sirfsoc_i2c_of_match[] __devinitconst = {
> +	{ .compatible = "sirf,prima2-i2c", },
> +	{},
> +};

Is the binding documented?

> +MODULE_DEVICE_TABLE(of, sirfsoc_i2c_of_match);
> +
> +static struct platform_driver i2c_sirfsoc_driver = {
> +	.driver = {
> +		.name = "sirfsoc_i2c",
> +		.owner = THIS_MODULE,
> +#ifdef CONFIG_PM
> +		.pm = &i2c_sirfsoc_pm_ops,
> +#endif
> +		.of_match_table = sirfsoc_i2c_of_match,
> +	},
> +	.probe = i2c_sirfsoc_probe,
> +	.remove = __devexit_p(i2c_sirfsoc_remove),
> +};
> +
> +static int __init i2c_sirfsoc_init(void)
> +{
> +	return platform_driver_register(&i2c_sirfsoc_driver);
> +}
> +arch_initcall(i2c_sirfsoc_init);
> +
> +static void __exit i2c_sirfsoc_exit(void)
> +{
> +	platform_driver_unregister(&i2c_sirfsoc_driver);
> +}
> +module_exit(i2c_sirfsoc_exit);

module_platform_driver()

> +
> +MODULE_DESCRIPTION("SiRF SoC I2C master controller driver");
> +MODULE_AUTHOR("Zhiwu Song <Zhiwu.Song at csr.com>, "
> +	"Xiangzhen Ye <Xiangzhen.Ye at csr.com>");
> +MODULE_LICENSE("GPL v2");
> diff --git a/drivers/i2c/busses/i2c-sirf.h b/drivers/i2c/busses/i2c-sirf.h
> new file mode 100644
> index 0000000..28f4ada
> --- /dev/null
> +++ b/drivers/i2c/busses/i2c-sirf.h
> @@ -0,0 +1,61 @@
> +/*
> + * I2C bus drivers for CSR SiRFprimaII
> + *
> + * Copyright (c) 2011 Cambridge Silicon Radio Limited, a CSR plc group company.
> + *
> + * Licensed under GPLv2 or later.
> + */
> +
> +#ifndef _SIRFSOC_I2C_BUS_H_
> +#define _SIRFSOC_I2C_BUS_H_
> +
> +#include <linux/bitops.h>
> +
> +#define SIRFSOC_I2C_CLK_CTRL		0x00
> +#define SIRFSOC_I2C_STATUS		0x0C
> +#define SIRFSOC_I2C_CTRL		0x10
> +#define SIRFSOC_I2C_IO_CTRL		0x14
> +#define SIRFSOC_I2C_SDA_DELAY		0x18
> +#define SIRFSOC_I2C_CMD_START		0x1C
> +#define SIRFSOC_I2C_CMD_BUF		0x30
> +#define SIRFSOC_I2C_DATA_BUF		0x80
> +
> +#define SIRFSOC_I2C_CMD_BUF_MAX		16
> +#define SIRFSOC_I2C_DATA_BUF_MAX	16
> +
> +#define SIRFSOC_I2C_CMD(x)		(SIRFSOC_I2C_CMD_BUF + (x)*0x04)
> +#define SIRFSOC_I2C_DATA_MASK(x)        (0xFF<<(((x)&3)*8))
> +#define SIRFSOC_I2C_DATA_SHIFT(x)       (((x)&3)*8)
> +
> +#define SIRFSOC_I2C_DIV_MASK		(0xFFFF)
> +
> +/* I2C status flags */
> +#define SIRFSOC_I2C_STAT_BUSY		BIT(0)
> +#define SIRFSOC_I2C_STAT_TIP		BIT(1)
> +#define SIRFSOC_I2C_STAT_NACK		BIT(2)
> +#define SIRFSOC_I2C_STAT_TR_INT		BIT(4)
> +#define SIRFSOC_I2C_STAT_STOP		BIT(6)
> +#define SIRFSOC_I2C_STAT_CMD_DONE	BIT(8)
> +#define SIRFSOC_I2C_STAT_ERR		BIT(9)
> +#define SIRFSOC_I2C_CMD_INDEX		(0x1F<<16)
> +
> +/* I2C control flags */
> +#define SIRFSOC_I2C_RESET		BIT(0)
> +#define SIRFSOC_I2C_CORE_EN		BIT(1)
> +#define SIRFSOC_I2C_MASTER_MODE		BIT(2)
> +#define SIRFSOC_I2C_CMD_DONE_EN		BIT(11)
> +#define SIRFSOC_I2C_ERR_INT_EN		BIT(12)
> +
> +#define SIRFSOC_I2C_SDA_DELAY_MASK	(0xFF)
> +#define SIRFSOC_I2C_SCLF_FILTER		(3<<8)
> +
> +#define SIRFSOC_I2C_START_CMD		BIT(0)
> +
> +#define SIRFSOC_I2C_CMD_RP(x)		((x)&0x7)
> +#define SIRFSOC_I2C_NACK		BIT(3)
> +#define SIRFSOC_I2C_WRITE		BIT(4)
> +#define SIRFSOC_I2C_READ		BIT(5)
> +#define SIRFSOC_I2C_STOP		BIT(6)
> +#define SIRFSOC_I2C_START		BIT(7)
> +
> +#endif

Regards,

   Wolfram



More information about the linux-arm-kernel mailing list