[PATCH v2 1/2] mmc: atmel-mci: DMA can be used with other controller

Hein Tibosch hein_tibosch at yahoo.es
Thu Aug 30 12:34:38 EDT 2012


After the latest changes to atmel-mci, it could not be used with
DMA on the AVR32 platform. This patch will allow to use DMA again
and it will avoid access to MCI register ATMCI_DMA.

v2:
Even if the IP version is lower than v3xx and doesn't have the DMA
configuration register, DMA transfers can be used with a different
controller than the Atmel AHB DMA one. For instance, some AVR chips use 
the Synopsys DesignWare AHB DMA controller.

v2: in atmci_configure_dma: check both pdata and pdata->dma_slave


Signed-off-by: Hein Tibosch <hein_tibosch at yahoo.es>
Acked-by: Ludovic Desroches <ludovic.desroches at atmel.com>
---
 drivers/mmc/host/atmel-mci.c |   26 +++++++++++++-------------
 1 files changed, 13 insertions(+), 13 deletions(-)

diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c
index f2c115e..a6a5593 100644
--- a/drivers/mmc/host/atmel-mci.c
+++ b/drivers/mmc/host/atmel-mci.c
@@ -71,7 +71,7 @@ enum atmci_pdc_buf {
 };
 
 struct atmel_mci_caps {
-	bool    has_dma;
+	bool    has_dma_conf_reg;
 	bool    has_pdc;
 	bool    has_cfg_reg;
 	bool    has_cstor_reg;
@@ -411,7 +411,7 @@ static int atmci_regs_show(struct seq_file *s, void *v)
 	atmci_show_status_reg(s, "SR", buf[ATMCI_SR / 4]);
 	atmci_show_status_reg(s, "IMR", buf[ATMCI_IMR / 4]);
 
-	if (host->caps.has_dma) {
+	if (host->caps.has_dma_conf_reg) {
 		u32 val;
 
 		val = buf[ATMCI_DMA / 4];
@@ -767,7 +767,7 @@ static void atmci_dma_complete(void *arg)
 
 	dev_vdbg(&host->pdev->dev, "DMA complete\n");
 
-	if (host->caps.has_dma)
+	if (host->caps.has_dma_conf_reg)
 		/* Disable DMA hardware handshaking on MCI */
 		atmci_writel(host, ATMCI_DMA, atmci_readl(host, ATMCI_DMA) & ~ATMCI_DMAEN);
 
@@ -954,7 +954,9 @@ atmci_prepare_data_dma(struct atmel_mci *host, struct mmc_data *data)
 		maxburst = atmci_convert_chksize(host->dma_conf.dst_maxburst);
 	}
 
-	atmci_writel(host, ATMCI_DMA, ATMCI_DMA_CHKSIZE(maxburst) | ATMCI_DMAEN);
+	if (host->caps.has_dma_conf_reg)
+		atmci_writel(host, ATMCI_DMA, ATMCI_DMA_CHKSIZE(maxburst) |
+			ATMCI_DMAEN);
 
 	sglen = dma_map_sg(chan->device->dev, data->sg,
 			data->sg_len, direction);
@@ -2161,7 +2163,10 @@ static bool atmci_configure_dma(struct atmel_mci *host)
 
 	pdata = host->pdev->dev.platform_data;
 
-	if (pdata && find_slave_dev(pdata->dma_slave)) {
+	if (!pdata)
+		return false;
+
+	if (pdata->dma_slave && find_slave_dev(pdata->dma_slave)) {
 		dma_cap_mask_t mask;
 
 		/* Try to grab a DMA channel */
@@ -2202,7 +2207,7 @@ static void __init atmci_get_cap(struct atmel_mci *host)
 	dev_info(&host->pdev->dev,
 			"version: 0x%x\n", version);
 
-	host->caps.has_dma = 0;
+	host->caps.has_dma_conf_reg = 0;
 	host->caps.has_pdc = 1;
 	host->caps.has_cfg_reg = 0;
 	host->caps.has_cstor_reg = 0;
@@ -2219,12 +2224,7 @@ static void __init atmci_get_cap(struct atmel_mci *host)
 		host->caps.has_odd_clk_div = 1;
 	case 0x400:
 	case 0x300:
-#ifdef CONFIG_AT_HDMAC
-		host->caps.has_dma = 1;
-#else
-		dev_info(&host->pdev->dev,
-			"has dma capability but dma engine is not selected, then use pio\n");
-#endif
+		host->caps.has_dma_conf_reg = 1;
 		host->caps.has_pdc = 0;
 		host->caps.has_cfg_reg = 1;
 		host->caps.has_cstor_reg = 1;
@@ -2298,7 +2298,7 @@ static int __init atmci_probe(struct platform_device *pdev)
 
 	/* Get MCI capabilities and set operations according to it */
 	atmci_get_cap(host);
-	if (host->caps.has_dma && atmci_configure_dma(host)) {
+	if (atmci_configure_dma(host)) {
 		host->prepare_data = &atmci_prepare_data_dma;
 		host->submit_data = &atmci_submit_data_dma;
 		host->stop_transfer = &atmci_stop_transfer_dma;
-- 
1.7.8.0




More information about the linux-arm-kernel mailing list